• Journal of Korean Society of Forest Science
• /
• v.30 no.1
• /
• pp.19-29
• /
• 1976

The fiberboard and paper mills in this country are much affected by the price hikes and shortage of phenolic resins, since phenolic acid as a raw material depends on imported good. It is prerequisite to fiberboard industry to help replace with other sized and stabilize the prices and supply of them, improving the quality of boards. Thus, the present study was carried out to examine the effect of strength increasing sized such as urea formaldehyde resin (anion and cation type) and urea melamine copolymer resin, on the quality of the wet forming hardboard, and comparing them with two types of proprietary modified melamine resins, and ordinary size, phenol resin. The Asplund pulp was prepared from wood wastes mixed with 20 percent of lauan and 80 percent of pines as a fibrous material. After sizing agents were added at a pH of 4.5 for 10 minutes with alum in the beater, the stock was made in the form of wet sheet, prepared, and then performed by hot pressing cycle: $180^{\circ}C$, $50-6-5kg/cm^2$, 1-2-7 minutes. The properties of hardboard were examined after air conditioning. The results obtained are summarized as follows: 1. There is a significant difference in specific gravity among hardboards that were treated with strength increasing resins, but no difference is effected by the increase in the resin content. In the case of modified melamine resin, its specific gravity is highest. The middle group comprises cation type of urea resin, anion type of urea resin, and acid colloid of urea-melamine copolymer resin. The lowest is phenolic resin. 2. The difference of the moisture content of hardboard both by the resins and by the amount of each resin applied is significant. The moisture content of hardboard becomes lower along with the increase of each resin content, but there is no difference between 2 and 3 percent. 3. For water absorption, there is a significant difference both in the adhesives used and in the amount of paraffin wax emulsion. The water resistance becomes higher inn proportion to the content of the paraffin wax emulsion. To satisfy KS F standards of the water resistance, a proprietary modified melamine resin (p-6100) and modified cation type of urea resin (p-1500) do not require any paraffin wax emulsion, but in the case of anion type of urea resin, cation type of urea resin, and urea-melamine copolymer resin, 1 percent of paraffin wax emulsion is needed, and 2 percent of paraffin wax emulsion in the case of phenolic resin. 4. The difference of flexural strength of hardboard both by the resins and by the amount of each resin is significant. Modified melamine resin shows the highest degree of flexural strength. Among the middle group are urea-melamine copolymer resin, p-1500, anion type of urea resin, and cation type of urea resin. Phenolic resin is the lowest. The cause may be attributable to factors combined with the pressing temperature, sizing effect, and thermal efficiency of press platens heated electrically. 5. Considering the economic advantages and properties of hardboard, it is proposed that urea-melamine copolymer resin and cation type of urea resin be used for the development of the fiberboard industry. It is desirable to further develop the modified urea-melamine copolymer resin and cation type of urea resin through continuous study.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.4
• /
• pp.605-616
• /
• 2004

Subinhibitory concentrations (sub-MICs) refer to concentrations below minimum inhibitory concentrations (MICs). The antimicrobial agents may be present at relatively high concentration, at least higher than bacterial MIC and thereafter be deserted off a surface and function at sub-MICs, perhaps by interfering with bacterial metabolism. Consequently, the aim of this study was to determine the effects of growth, in the presence of sub-MICs of antimicrobial agents, on the cell surface properties and virulence factors of mutans streptococci and to investigate the efficacy of a chemical approach in vitro. Streptococcus mutans Ingbritt and Streptococcus sobrinus 6715-7 were used. Eight antimicrobial agents (Sanguinaria extract;SG, Chlorhexidine digluconate;CHX, Fluoride;F, Propolis;PP, Hydrogen peroxide;HP, Triclosan;TC, Sodium dodecyl sulfate;SDS Cetylpyridinium chloride; CC) were diluted serially in broth to determine MICs and to compare the growth rate, acid production, hydrophobicity, adhesion activity to saliva coated hydroxyapatite, glucan synthesis and cellular aggregation of experiment groups (in the presence of sub-MICs) with those of control (in the absence of antimicrobial agents). Sub-MICs of antimicrobial agents affected the growth of cells, hydrophobicity, and adhesion of bacteria to saliva coated hydroxyapatite and glucan synthesis. They also resulted in a significant reduction in pH after 12 hours (p<0.05). By cells pretreated with proteinase K, either the aggregation induced by antimicrobial agents was completely inhibited or the aggregation titers were markedly increased. According to the results of the present study, each antimicrobial agent at sub-MICs could affect similar as its known action mechanism and could continually inhibit cariogenic bacteria at such concentrations. Thus, the use of these antimicrobial agents would be one of the effective methods to prevent dental caries.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.36 no.3
• /
• pp.100-114
• /
• 2018

Nationally designated Cultural Properties 'Scenic site No.12 Maisan Mountain, Jinan' designated areas and some protected areas, and taking into account the dynamics of naturalized plants causing problems, we will restore the original vegetation scenery of Mt. Maisan. The results of this study are as follows. A total of 76 families, 192 genera, 286 taxa, and inland and inhabited areas, 76 and 138 genera and 163 taxa were identified in the areas of Ammaibong. The total number of naturalized plants identified in this study area is 28 taxa total, which corresponds to 7.1% naturalization rate(NR) among the vascular plants of all 395 taxa, and the urbanization index(UI) corresponds to 8.4% of the 333 taxa of Korean naturalized plants. Ecosystem disturbance plants identified in the survey area were Ambrosia artemisiifolia 1 taxa. The naturalized plants controlled and managed by separate anthropogenic vegetation management within the designation and protection area of Maisan scenic place are three species of herbaceous Rumex acetosella, A. artemisiifolia and Festuca arundinacea. It was identified as a breed. Indigofera bungeana and F. arundinacea communities around the stairway and Amorpha fruticosa, I. bungeana, A. artemisiifolia and Amaranthus patulus of the top of Am-Maibong were selected as the first priority sites for exclusion of exotic species in Maisan area and target naturalized plants species to the Ammaibong peak. In addition, R. acetosella community around the temple was suggested to be removed first to preserve endemic species. For the restoration of vegetation, we suggest that Stephanandra incisa, Spiraea blumei, Weigela subsessilis, etc. should be planted after removal of I. bungeana, and F. arundinacea, C. lanceolata, Carex callitrichos var. nana.

• Tuberculosis and Respiratory Diseases
• /
• v.64 no.3
• /
• pp.194-199
• /
• 2008

Background: Early identification of pathogens can improve the prognosis of patients with ventilator associated pneumonia (VAP). In the present study, we evaluated the feasibility of performing multiplex PCR for endotracheal aspirates to detect three important pathogens (P. aeruginosa, K. pneumoniae and MRSA) in patients with VAP. Methods: The endotracheal aspirates of 24 patients were collected within 24 hours of the diagnosis of VAP for performing multiplex PCR. Forward and reverse primers were designed to target the specific site of each pathogen (the oprL gene for P. aeruginosa, 16S rRNA for K. pneumoniae and the mec gene for MRSA). We analyzed the clinical data of the VAP patients, including the culture reports for the endotracheal aspirates. Results: Twenty-four patients (M:F=18:6, mean age=$70{\pm}11$) with VAP were enrolled. Pathogens were isolated from 11 patients (P. aeruginosa in 2, K. pneumoniae in 1, MRSA in 2, other enteric Gram negative bacilli in 3, S. pneumoniae in 2 and mixed infection in 1). Multiplex PCR detected three cases of P.aeruginosa (2 cases coincided with the culture reports) and four cases of K. pneumoniae (1 matched with the culture report). PCR detected two MRSA cases, which did not coincide with the culture reports. Conclusion: Multiplex PCR of the endotracheal aspirate showed some ability to detect Gram negative bacilli, although caution is required when interpreting the results.

• Journal of Korean Society of Forest Science
• /
• v.106 no.3
• /
• pp.275-287
• /
• 2017

The purpose of this study was to analyze forest vegetation type classification and relationships between the type and environment factor in Mt. Dutasan. Data were collected by total of forty six plots using Z-M phytosociological method from June to October, 2016, and analyzed by vegetation classification, canopy layer structure and relationships between vegetation unit and environment factor using coincidence methods. As a result of vegetation type classification, Quercus mongolica community group was classified at a top level of vegetation hierarchy that was classified into Rhododendron schlippenbachii community and Betula costata community. R. schlippenbachii community was divided into Lychnis cognata group and R. schlippenbachii typical group. L. cognata group was subdivided into Veratrum oxysepalum subgroup and L. cognata typical subgroup. B. costata community was divided into Fraxinus mandshurica group and Betula schmidtii group. F. mandshurica group was subdivided into Weigela subsessilis subgroup and Cimicifuga heracleifolia subgroup. Therefore the forest vegetation was composed of six vegetation units with two kinds of bisected species groups and fourteen species groups. As the result of an analysis of canopy layer structure, there were two kinds of structures with monotonous structures V. oxysepalum subgroup (vegetation units 1), L. cognata typical subgroup (vegetation units 2), W. subsessilis subgroup (vegetation units 4) and complicated structures R. schlippenbachii typical group (vegetation units 3), C. heracleifolia subgroup (vegetation units 5), Betula schmidtii group (vegetation units 6). The vertical layer structure of vegetation unit 5 was the most developed and vegetation unit 6 had the lowest coverage of herb layer. According to the correlation between vegetation unit and environmental factor, R. schlippenbachii community (vegetation units 1~3) and B. costata community (vegetation units 4~6) were classified based on 1,100 m of altitude, middle slope, twenty of slope degree, twenty percents of bare rock and thirty centimeters of DBH in tree layer. R. schlippenbachii community (vegetation units 1~3) showed positive correlation with altitude, topography and B. costata community (vegetation units 4~6) showed negative correlation tendency with them.

• Korean Journal of Ecology and Environment
• /
• v.44 no.2
• /
• pp.239-251
• /
• 2011

To compare the different water environments in the Jigsaw stream (st. 1, 2) and Jujin stream (st. 3, 4) crossing over the Byeonsan-Bando and Seonunsan parklands, the physico-chemical factors and the species compositions of epilithic diatoms were analyzed from March 2009 to February 2010. The mean values of conductivity (681.1 ${\mu}S\;cm^{-1}$), suspended solids (27.83 mg $L^{-1}$), biological oxygen demand (3.15 mg $L^{-1}$), total nitrogen (3.24 mg $L^{-1}$), total phosphorus (0.24 mg $L^{-1}$) and chlorophyll-${\alpha}$ (12.99 mg $m^{-3}$ ) in Jujin stream were significantly higher than each element in Jigsaw stream. Eighty taxa were classified into 73 species and seven varieties belonging to 24 genera, eight families, three suborders and two orders in Jigsaw stream. Eighty eight taxa were classified into 81 species and seven varieties belonging to 22 genera, seven families, three suborders and two orders in Jujin stream. Biological water quality assessments revealed that Jigsaw stream was ${\beta}$~${\alpha}$-oligosaprobic and Jujin stream was ${\beta}$-mesosaprobic. Dominant and diversity indices were indicated from 0.25~0.81 and from 1.73~4.14 in Jigsaw stream, respectively, and from 0.29~0.64 and from 2.72~4.02 in Jujin stream, respectively. Jujin stream was more eutrophic than those of Jigsaw stream. The different water environments between the two streams could be due to the different ecosystems of the neighboring basins of each stream crossing over in the mountain. Further studies should investigate the water environments of two streams by continuous and regular monitoring to analyze the different ecosystem mechanisms.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1572-1578
• /
• 2007

The specified wastes consist of waste acid, waste alkali, waste oil, waste organic solvent, waste resin, dust, sludge, infectious waste, and others. Among these specified wastes, a great portion is liquid phase wastes. The purpose of this study is to develop the high temperature and high pressure (HTHP) treatment system for decomposition of the liquid phase specified waste (LPSW). For this, we analyzed the physical and chemical properties of the LPSW such as density, proximate analysis, ultimate analysis, heating values, and designed 0.3 ton/day HTHP treatment system. The LPSW tested in this experiment were prepared by adding TCE(trichloroethylene) and toluene to liquid phase waste which was brought into the commercial waste treatment company. The average density of waste oil (25 samples), waste resin (5 samples), and waste solvent (12 samples) was 0.99 g/mL, 0.91 g/mL, and 0.93 g/mL, respectively. And the average lower heating value of waste oil, waste resin, and waste solvent was 8,294 kcal/kg, 5,809 kcal/kg, and 7,462 kcal/kg, respectively. The DRE (Destruction & Removal Efficiency) of TCE and toluene were 99.95% and 99.73% at atmospheric pressure conditions and that were 99.99% and 99.82% at pressurized conditions, respectively. These results showed that TCE/toluene mixtures were properly decomposed over about 99.73% of DRE by the HTHP treatment system and pressurized conditions were more effective to destroy those pollutants than atmospheric pressure conditions. Also these systems could be directly applied to industries which try to treat the liquid phase specified waste within the regulation limit.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.1049-1057
• /
• 2012

The study investigated the biochemical methane potential (BMP) assay of pig slurry supplemented with mixed methanogens and cellulolytic bacteria to improve anaerobic digestion for methane production. For the BMP assay, 7 different microbial supplementation groups consisted of the cultures of mixed methanogens (M), Fibrobacter succinogenes (FS), Ruminococcus flavefaciensn (RF), R. albus (RA), RA+FS, M+RA+FS, and control. The cultures were added in the batch reactors with the increasing dose levels of 1% (0.5 mL), 3% (1.5 mL) and 5% (2.5 mL). Incubation for the BMP assay was carried out for 60 days at $38^{\circ}C$ using anaerobic digestate obtained from an anaerobic digester with pig slurry as inoculum. In results, 5% RF and RA+FS increased total biogas up to 8.1 and 8.4%, respectively, compared with that of control (p<0.05). All 5% microbial culture supplements significantly increased methane production up to 12.1~17.9% compared with that of control (p<0.05). Total solid (TS) and volatile solid (VS) digestion efficiencies showed no relationship to the increased supplementation levels of microbial cultures. After incubation, pH values in all treatment groups ranged between 7.527 and 7.657 indicating that methanogensis was not inhibited during the incubation. In conclusion, the results indicated that both hydrolysis and methanogenesis stages for methane production in anaerobic batch reactors were influenced by the supplemented microorganisms due to the chemical characteristics of pig slurry, but only the 5% supplementation level of all microbial culture supplements used in the experiment affected methane production.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.107-108
• /
• 2008

The spectacular development of AMLCDs, been made possible by a-Si:H technology, still faces two major drawbacks due to the intrinsic structure of a-Si:H, namely a low mobility and most important a shift of the transfer characteristics of the TFTs when submitted to bias stress. This has lead to strong research in the crystallization of a-Si:H films by laser and furnace annealing to produce polycrystalline silicon TFTs. While these devices show improved mobility and stability, they suffer from uniformity over large areas and increased cost. In the last decade we have focused on microcrystalline silicon (${\mu}c$-Si:H) for bottom gate TFTs, which can hopefully meet all the requirements for mass production of large area AMOLED displays [1,2]. In this presentation we will focus on the transfer of a deposition process based on the use of $SiF_4$-Ar-$H_2$ mixtures from a small area research laboratory reactor into an industrial gen 1 AKT reactor. We will first discuss on the optimization of the process conditions leading to fully crystallized films without any amorphous incubation layer, suitable for bottom gate TFTS, as well as on the use of plasma diagnostics to increase the deposition rate up to 0.5 nm/s [3]. The use of silicon nanocrystals appears as an elegant way to circumvent the opposite requirements of a high deposition rate and a fully crystallized interface [4]. The optimized process conditions are transferred to large area substrates in an industrial environment, on which some process adjustment was required to reproduce the material properties achieved in the laboratory scale reactor. For optimized process conditions, the homogeneity of the optical and electronic properties of the ${\mu}c$-Si:H films deposited on $300{\times}400\;mm$ substrates was checked by a set of complementary techniques. Spectroscopic ellipsometry, Raman spectroscopy, dark conductivity, time resolved microwave conductivity and hydrogen evolution measurements allowed demonstrating an excellent homogeneity in the structure and transport properties of the films. On the basis of these results, optimized process conditions were applied to TFTs, for which both bottom gate and top gate structures were studied aiming to achieve characteristics suitable for driving AMOLED displays. Results on the homogeneity of the TFT characteristics over the large area substrates and stability will be presented, as well as their application as a backplane for an AMOLED display.

• Clinical and Experimental Reproductive Medicine
• /
• v.21 no.2
• /
• pp.165-176
• /
• 1994

This study was carried out to investigate the effect of the timing and dose of human chorionic gonadotropin(hCG) on oocyte recovery, in vitro fertilization, and preimplantation development in superovulation of mouse. F1 hybrid($C57BL{\times}CBA$) mice were obtained and superovulation was induced in female mice by sequential intraperitoneal injection of PMSG and hCG. In the first series of experiments, mice received 5 IU of PMSG given intraperitoneally, and 48 hours later were injected 1 IU, 5 IU, or 10 IU of hCG respectively. In the second series of experiments, mice received 5 IU of PMSG given intraperitoneally and were injected 5IU of hCG 36, 48, or 60 hours later respectively. 1. When the mice received 5 IU of PMSG given intraperitoneally and 48 hours later were injected 1 ItT, 5 IU, or 10 IU of hCG respectively, there were no differences in the total number of the oocytes obtained from the three experimental groups. When the cultures were examined 48 hrs after the termination of insemination the proportion of unfragmented oocytes which had developed over two-cell stage was observer to be lowest in 10 IU hCG group. When the cultrues were examined 120 hour after termination of insemination the proportion of embryos which had developed to the blastocyst stage was observed to be significantly higher in 10IU hCG group than 5IU hCG group(p<0.05), but there was no difference between 10 IU hCG group and 1IU hCG group. 2. When the mice received 5 IU of PMSG and were injected 5 IU of hCG 36, 48, or 60 hours later respectively, there were no differences in the total number of oocytes obtained from the three experimental groups. When cultures were examined 48 hour after the termination of insemination the proportion of unfragmented oocytes which had developed over two-cell stage was observed to be significantly lower in 36 hour interval group than 48 hour interval and 60 hour interval group(p<0.05). When the cultures were examined 120 hour after termination of insemination the proportion of embryos which had developed to the blastocyst stage was found to be higher in 60 hour interval group than 36 interval or 48 hour interval group (P<0.05), and the proportion of hatching blastocyst was found to be higher in 60 hour interval group as well. In this study, it was concluded that the administration of adequate dose of hCG, and long (60 hour) PMSG-hCG interval were necessary in superovulation of mice($C57BL{\times}CBA$) in order to get a large number of oocytes which had an early oocytes which had an early embryonic developmental capability when fertilized in vitro, and especially it had better have been avoided to administer a large dose of hCG.