• Geophysics and Geophysical Exploration
• /
• v.20 no.2
• /
• pp.78-87
• /
• 2017

For efficient data processing, trace interpolation and regularization techniques should be antecedently applied to the seismic data which were irregularly sampled with missing traces. Among many interpolation techniques, MWNI (Minimum Weighted Norm Interpolation) technique is one of the most versatile techniques and widely used to regularize seismic data because of easy extension to the high-order module and low computational cost. However, since it is difficult to interpolate spatially aliased data using this technique, model-constrained MWNI was suggested to compensate for this problem. In this paper, conventional MWNI and model-constrained MWNI modules have been developed in order to analyze their performance using synthetic data and validate the applicability to the field data. The result by using model-constrained MWNI was better in spatially aliased data. In order to verify the applicability to the field data, interpolation and regularization were performed for two field data sets, respectively. Firstly, the seismic data acquired in Ulleung Basin gas hydrate field was interpolated. Even though the data has very chaotic feature and complex structure due to the chimney, the developed module showed fairly good interpolation result. Secondly, very irregularly sampled and widely missing seismic data was regularized and the connectivity of events was quite improved. According to these experiments, we can confirm that the developed module can successfully interpolate and regularize the irregularly sampled field data.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.21 no.6
• /
• pp.731-737
• /
• 1992

The specific attributes of aroma quality of canned tuna meat were investigated before and during refrigerated storage. Fresh, cooked tuna, beefy and meaty flavor notes of canned tuna meat were changed to card-boardy(1 week storage), oxidized fat-like(2 weeks storage), fatty acid-like and heavy oxidized fat-like(3 weeks storage), and then moldy and painty(4 weeks storage) flavor notes during storage in refrigerator at $4^{\circ}C.$ More than 126 peaks of volatile compounds collected from canned tuna meat were separated on Carbowax 20M capillary column of gas chromatographic analysis. Of the peaks, 54 compounds were identified by mass spectral data, matching $I_E$ values, and sniffing the effluent of each peak from GC detector. The contents of many low molecular weight compounds eluted with early retention times were decreased, whereas some other new compounds eluted with longer retention time were formed during storage. The compounds increased up to 3 weeks of storage and then decreased at extended storage time(4 weeks) were 1-penten-3-ol, 3-penten-2-ol, heptanal, limonene, 1-pentanol, octanal, 1-hexanol, nonanal, 2-octanone, 2-nonanone, 1-heptanol, benzaldehytde and some methyl substituted benzenes. p-Thiocresol, 2-chlorophenol, and 2-heptylthiophene were formed after 4 weeks of storage, but not detected in fresh canned tuna. Therefore, these compounds could be used as indicators for the quality changes during refrigerated storage.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.870-878
• /
• 2010

We investigated the concentration and the sources of ubiquitous persistent organic pollutants [i.e., 17 toxic polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), 12 coplanar polychlorinated biphenyls (Co-PCBs), and 16 priority polycyclic aromatic hydrocarbons (PAHs)] in waste papers and lumbers from industrial complexes. The total concentrations in waste papers and lumbers ranged from 9.69~176.77 pg/g-dry and 0.14~0.25 pg/g-dry for 17 PCDD/Fs, 109.95~4097.25 pg/g-dry and 28.23~59.88 pg/g-dry for 12 Co-PCBs and 9.30~52.18 ng/g-dry and 0.82~1.82 ng/g-dry for 16 PAHs respectively. Generally, the concentration of these pollutants in waste papers was higher than those in waste lumbers. OCDD was dominant in waste papers and lumbers and the PCDD/F patterns of these samples were similar with that of stack gas. The distribution patterns of Co-PCBs in wastes were related with commercial PCB products, indicating the effect of commercial PCB products on ubiquitous environment. The diagnostic ratios of several PAH compounds in waste paper showed that they were related with pyrogenic sources.

• Resources Recycling
• /
• v.8 no.4
• /
• pp.45-56
• /
• 1999

The purpose of tlus sludy was to preparc raw material powder for Mn-Zn iclrile, h m mined mill scale and fero-Mn, usins a co-spray roasting process The mill scale and ferra-Mn uscd in this raalins process was rcf~nedb y mesn-ns of a slxc~apl rxcss ~nvolvinm~a te~ialsc ontalning imp~u-ltleso r less than 100 pprn In this study an effeclive spray roaster system. wllich produces fme complex oxide powder, collects produccd ~owder.,m d prcvel~tse ~~llssiooifi HCI gas. was also manufactured. By means of spray~ngp urifcd raw malerial solu~lionl nln a manufacued high tcmpervture rumace. &-ferrite powder and a comnpleu o ~ d e powder of Fe,O; and M,x203 were manufactured. The chmcterlstics of the composllion. surface urca, and p'miicle size dismbulion or the produced powder were exmined. ptoduced powdcr was then ~ m e dwi tli ZnO powder. aid olher addilives of defined cornposnion, and Mn-Zn femite cares werc praiuccil by meuns of Sorlning and closely controlled sintering processes. The magpelic p~oprlieso f c olo~ss, initlal permeability. mauin~u~mnn agnehc flux. coz~civcr orcc and residual magnccic flux for the above cores we,= measured, and fmm Il~ase I-csulls the eflicacy of lhe co-spray roasling pncess to pl.ellare raw material powder lor Mn-Zn ferntc was established

• Journal of the Korean Magnetics Society
• /
• v.9 no.1
• /
• pp.35-40
• /
• 1999

Sr substituted materials for some barium in M-type barium ferrite powder and Co-Ti substituted Sr-Ba hexagonal ferrite powder were prepared by citrate sol-gel method and 2 MOE sol-gel method these hexaferrite particles were reduced for 1hr in the hydrogen gas. The reduction temperatures were varied in the range of 250 $^{\circ}C$ to 500 $^{\circ}C$. X-ray diffraction patterns were measured using diffractometer with Cu $K_{\Alhpa}$ radiation. Mossbauer absorption spectra were measured with a constant acceleration spectrometer. We have focused on studying the origin of increasing $M_s$ by M$\"{o}$ssbauer spectroscopy. Ferrite particles which were sintered at 105$0^{\circ}C$ were found to be typical magnetoplumbite structure and single phase. XRD patterns with varying the reduction temperatures in $Sr_{0.5}Ba_{0.5}Fe_{10}O_{19}$ indicates ferrites particles become composite hexaferrites containing $\alpha$-Fe at T_{red}=350 \;$^{\circ}C$$. On the otherhand, it was found that $Co^{2+}$ ions and $Ti^{4+}$ ions in $Sr_{0.7}Ba_{0.3}Fe_{10}CoTiO_{19}$ prevent from changing $Fe^{3+}$ ions to $\alpha$-Fe during the $H_2$ reduction. Comparing Mossbauer results with XRD results, we have determined most of $\alpha$-Fe are reduced from $4f_{vi}$ sites and 12k sites of $Fe^{3+}$ ions. These $\alpha$-Fe phase bring the induced anisotropy and increase saturation magnetization $M_s$.TEX>.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.45-57
• /
• 2002

In this paper, the results gained by applying many impingement models to the cylinder and flat plate were analyzed in comparison with the experimental data to study a spray/wall interaction phenomena. To begin with, the behavior of spray injected normal to the wall was analysed using three different impingement models ; Naber and Reitz model(NR model), Watkins and Wang model(WW model) and Park and Watkins model(PW model) in the present calculation. The results obtained from these models were compared with experimental data of Katsura et. al. The results indicated that PW model was in better agreement with experimental data than the NR and WW model. Also f3r spray injected at 30DEG , the result of three models were compared with experimental data of Fujimoto et. al. The results showed that m model overpredicted the penetration in the radial direction because this model was based on the inviscid jet analogy. WW model did not predicted the radius and height of the wall spray effectively. It might be thought that this discrepancy was due to the lack of consideration of spray film velocity occurred at impingement site. The result of PW model agrees with the experimental data as time goes on. In particular, a height of the spray droplets was predicted more closely to the experimental data than the other two models. The results of PW model in which the spray droplets were distributed densely around the edge of droplet distribution shaped in a circle had an agreement with the experimental data of Fujimoto et. al. Therefore, it was concluded that PW model performed better than M and WW model for prediction of spray behavior. The numerical calculation using PW model performed to the cylinder similar to the real shape of DI engine. The results showed that vortex strength near the wall in the cylinder was stronger than that in the case of flat plate. Contrary to the flat plat, an existence of the side wall in the cylinder caused the tangential velocity component to be reduced and the normal velocity component to be increased. The flow tends to rotate to the inside of cylinder going upward to the right side wall of cylinder gradually as time passes. Also, the results showed that as the spray angle increases, the gas velocity distribution and the tumble flow seemed to be formed widely.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.1-8
• /
• 2017

In this study, we applied microcellular foaming injection molding process to improve the performance of system air-conditioner drain fan which had been produced by injection molding process and studied the optimization of process conditions through 6-sigma process and response surface method (RSM) to reduce weight and deformation of products. Additive type, melt temperature, mold temperature, and injection screw shape were selected as the factor affecting the weight and deformation of the products by carrying out analysis of trivial many through ANOVA and design of experiment (DOE) method. Among the effect factor, we set the addictive type to Long G/F and screw shape to foaming screw which had the highest level of weight reduction and deformation reduction. The amount of foaming agent gas was set at 60 ml, which was the limit beyond which the weight of product did not decrease any more. For melt temperature and mold temperature, we studied the conditions where both weight and deformation were minimized using the RSM. As a result, we set the melt temperature to $250^{\circ}C$, fixed mold temperature to $20^{\circ}C$, and moving mold temperature to $40^{\circ}C$. The improvement effect was analyzed by appling the selected optimal conditions to the production process using the microcellular foaming injection molding. The results showed that the mean weight of product was measured to be 1,420g which was 19% lower than that measured in the current process. The standard deviations of the weights were found to be similar to those in the current process and it showed a low dispersion. The mean deformation was measured to be 0.9237mm, which represented a 57% reduction compared to the mean deformation in the current process, and the standard deviation decreased from 0.3298mm to 0.1398mm. Moreover, we analyzed the process capability for deformation, and the results showed that the short-term process capability increased from 2.73 to 6.60 which was even higher than targeted level of 6.0.

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.1-6
• /
• 2002

How is the flow in a rotating impeller. About 35 years have passed since one experimentalist rotating with the impeller. of a huge centrifugal blower made the flow measurements using a hot-wire anemometer (Fowler 1968). Optical measurement methods have great advantages over the intrusive methods especially for the flow measurement in a rotating impeller. One is the optical flow visualization (FV) technique (Senoo, et al., 1968) and the other is the application of laser velocimetry (LV) (Hah and Krain, 1990). Particle image velocimetries (PIVs) combine major features of both FV and LV, and are very attractive due to the feasibility of simultaneous and multi-points measurements (Hayami and Aramaki, 1999). A high-pressure-ratio transonic centrifugal compressor with a low-solidity cascade diffuser was tested in a closed loop with HFC134a gas at 18,000rpm (Hayami, 2000). Two kinds of measurement techniques by image processing were applied to visualize a flow in the compressor. One is a velocity field measurement at the inducer of the impeller using a PIV and the other is a pressure field measurement on the side wall of the cascade diffuser using a pressure sensitive paint (PSP) measurement technique. The PIV was successfully applied for visualization of an unsteady behavior of a shock wave based on the instantaneous velocity field measurement (Hayami, et al., 2002b) as well as a phase-averaged velocity vector field with a shock wave over one blade pitch (Hayami, et al., 2002a. b). A violent change in pressure was successfully visualized using a PSP measurement during a surge condition even though there are still some problems to be overcome (Hayami, et al., 2002c). Both PIV and PSP results are discussed in comparison with those of laser-2-focus (L2F) velocimetry and those of semiconductor pressure sensors. Experimental fluid dynamics (EFDs) are still growing up more and more both in hardware and in software. On the other hand, computational fluid dynamics (CFDs) are very attractive to understand the details of flow. A secondary flow on the side wall of the cascade diffuser was visualized based either steady or unsteady CFD calculations (Bonaiuti, et al.,2002). EFD and CFD methods will be combined to a hybrid method being complementary to each other. Measurement techniques by image processing as well as CFD calculations give a huge amount of data. Then, data mining technique will become more important to understand the flow mechanism both for EFD and CFD.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.4
• /
• pp.148-154
• /
• 2019

Vanadium oxide based materials have been studied as novel negative electrode materials in lithium-ion batteries (LIBs) because of their high specific capacity. In this study, potassium metavanadate ($KVO_3$) was synthesized and its electrochemical properties are evaluated as a negative electrode materials. The aqueous solution of $NH_4VO_3$ is mixed with a stoichiometric amount of KOH. The solution is boiled to remove $NH_3$ gas and dried to obtain a precipitate. The obtained $KVO_3$ powders are heat-treated at 300 and $500^{\circ}C$ for 8 h in air. As the heat treatment temperature increases, the initial reversible capacity decreases, but the cycle performance and Coulombic efficiency are improved slightly. On the contrary, the electrochemical performances of the $KVO_3$ electrodes are greatly improved when a polyacrylic acid (PAA) as binder was used instead of polyvinylidene fluoride (PVDF) and a fluoroethylene carbonate (FEC) was used as electrolyte additive. The initial reversible capacity of the $KVO_3$ is 1169 mAh/g and the Coulombic efficiency is improved to 76.3% with moderate cycle performance. The $KVO_3$ has the potential as a novel high-capacity negative electrode materials.

• Food Science and Preservation
• /
• v.6 no.4
• /
• pp.351-356
• /
• 1999

To develop and extend the shelf-life of vitamin C enriched fresh-cut apples using CA stored Fuji apples, dipping in 10% L-ascorbic acid and packaging with 0.03 mm LDPE, 0.04 mm PP and 0.08 mm Nylon/PE film(N$_2$displacement) were carried out. The changes of gas concentrations in the packaging and quality attributes of fresh-cut apples were examined during storage at 10$^{\circ}C$. The concentrations of O$_2$was maintained lower in Nylon/PE film than the other film, the level of O$_2$was in the range of 1∼3%. The increase of C$_2$H$_4$ concentrations in Nylon/PE film bag was more suppressed than the others. The vitamin C content of fresh-cut apples was enriched by dipping in L-ascorbic acid solution up to 241 mg$.$100 g-1 f.w., and the loss or that content was retarded differently by the package conditions of lower O$_2$level during storage. Browning in fresh-cut apples was shown after 6 days of storage in LDPE and PP film. but it was not shown by 14 days of storage in Nylon/PE film. Spoilage and off odor in fresh-cut apples were not detected up to 14 days of storage in Nylon/PE film. The results indicated that the vitamin C enriched fresh-cut apples can be processed from the long-term CA stored apples, and maintaining high quality of the products ill be possible in cases of the application of sealing packaging after O$_2$removal with film having low O$_2$permeability.