• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.463-466
• /
• 2005

Restoring ductility or removing residual stresses is a necessary operation when a large amount of cold working is to be performed, such as in a cold-forging or warm forging process. The advantage of annealing temperatures was investigated. After Hydrostatic Extrusion process, extruded materials were annealed at $200^{\circ}C,\;350^{\circ}C,\;450^{\circ}C$ for 1 hour. Microstructure of the annealed material was observed to make an understand about the difference in mechanical properties.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.10
• /
• pp.180-187
• /
• 2004

Die design to minimize the die wear in the cold forging process is very important as it reduce the production cost and the increase of the production rate. The quantitative estimation fur the die wear is too hard because the die wear is caused by many process variables. So, in this paper, the optimal shape of the backward extrusion punch is newly designed through the FE-analysis considering the surface expansion and Archard wear model in order to reduce the rapid wear rate that is generated for the backward extruded products exceeding the forming limit. The main shape variables of the backward extrusion punch are the flat diameter, angle, and round of the punch nose part. As the flat diameter and angle of the punch nose are larger, the surface expansion is reduced and the wear rate is decreased according to the reduction of the punch round. These results obtained through this study can be applied to the real manufacturing process.

• Transactions of Materials Processing
• /
• v.1 no.1
• /
• pp.66-74
• /
• 1992

According to the variation of hydrostatic pressure on the central axis of deformable material, the V-shaped central bursting defect may be created in extrusion or drawing processes. The process factors which affect the generation of defects are semi-angle of die, reduction ratio of cross-sectional area, friction factor, material properties and so on. The combination of these factors can determine the possibility of defect creation and the shape of various round holes which have been created inside already. By the rigid plastic finite element method, this paper describes the observations of change in shape of round holes with process conditions such as semi-angle of die, reduction ratio of cross-sectional area and friction factor at the non-steady state of axisymmetrical extrusion process when the round hole is already existed inside the original billet. Also, the effects of process factors are investigated to prevent the possible defects.

• Design & Manufacturing
• /
• v.10 no.1
• /
• pp.12-18
• /
• 2016

Although magnesium alloy has received much attention to date for its lightweight and high specific strength, their applications are impeded by the low formability which is caused by the hexagonal crystal structure at room temperature. In general, equal-channel angular extrusion(ECAE) is recognized as one of the attractive severe plastic deformation techniques where the processed bulk metals generally achieve ultrafine-grained microstructure leading to improved physical characteristics and mechanical properties. ECAE process has several parameters such as angle of die, process temperature, process route and speed. During ECAE process of Mg alloy, these parameters has great influence on the extrudability and the mechanical properties of alloy. The aim of this study is to estimate the influences of process conditions on the formability of AZ31 and AZ31-CaO alloys. Mg alloys are processed through ECAE at elevated temperatures using three types of die with channel angle of $90^{\circ}$, $110^{\circ}$, $135^{\circ}$ using route $B_c$, respectively. This study discusses the feasibility of using ECAE to improve both formability and strength on magnesium alloys by comparative analyzing the mechanical properties and microstructural evolution in each condition.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.251-258
• /
• 2003

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. The paper discusses the influences of tool geometry such as punch nose angle, relative gap height, die comer radius on material flow and surface expansion into can and flange region. To analyze the process, numerical simulations by the FEM and experiment, an Al alloy as a model material have been performed. Based on the results, the influence of design parameters on the distribution of divided material flow and surface expansion are obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.80-87
• /
• 1996

The present paper will give some results of the fatigue behavior of typical axi-symmetric forward extrusion die. The extrusion process is analyzed by rigid-plastic FEM and the deformation analysis of extrusion die is conducted by elasto-plastic FEM. To approach the crack problem LEFM (Linear Elastic Fracture Mechanics) is introduced. Using special element in order to conside the sigularity of stress/ strain in the vicinity of the crack tip, stress intensity factor and the effective stress intensity factor is calculated. Applying proper fatigue crack propagation criterion such as Paris/Erdogan fatigue law and maximum principal criterion to these data, then, the angle and the direction of fatigue crack propagation is simulated. In result, it is proved that the simulated fatigue crack propagates in the zigzag path along the radial direction and fatigue life of the extrusion die is evaluated by using the computed crack growth rate.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.837-844
• /
• 1994

To investigate that the theoretical formulas for extrusion forces are applicable to the manufacturing plant, the maximum extrusion forces were calculated from Siebel's and Geleji's formulas and also measured using 550 ton extrusion press. Parameters such as flow stress, $K_f$, angle of dead metal zone, $\alpha$ were obtained experimentally in order to calculate the maximum extrusion forces by the the theoretical formulas, and it was showed that the results were reliable as the deformation efficient factor, $\eta _f$ was determined to be less than 0.5. The maximum extrusion forces calculated from Siebel's formula and Geleji's formula for the angle of dead metal zone, $\alpha = 50^{\circ}$ were approached to the experimental results. However, it was found that Siebel's formula is more useful to apply to the manufacturing plant.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.346-349
• /
• 2004

In the previous experimental study about extru-bending of angle product, the bending of extruded angle products with the '${\wedge}$' section and 'ㄱ' section can be abtained by the hot metal extru-bending machine with the two punches moving in the different velocity. The bending curvature can be controlled by the different velocity of billets through the two-hole container. This paper describes simulation of extru-bending process by the difference of punch velocities. The result of the forming simulation by $DEFORM^{TM}-3D$ shows that the bending phenomenon at the die exit during extrusion can be abtained by the two punches moving in the different velocity. And it is possible to design extrusion dies and to control the curvature of product through the simulation of extru-bending process by analysis

• Transactions of Materials Processing
• /
• v.10 no.4
• /
• pp.302-310
• /
• 2001

The twisting and extrusion process of the product with involute helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted inclined die surface connecting the die enterance section and the die exit section linearly. In the analysis, the internal shear surface is defined as the curved twisted plane from the twisting of die surface and the shear work is calculated by the consumption of shear energy. The increase rate of angular velocity is determined by the minimization of plastic work. The angular velocity of die exit can be controlled by the land length and the length of inclined die. The alular velocity assums to be increased linearly by the axial distance from the die enterance to the die exit. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction constant.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.42-47
• /
• 2012

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. We have discussed the influences of tool geometry such as punch nose angle, relative gap height, die corner radius on material flow and surface expansion into can and flange region. To analyse the process, numerical simulations by the FEM and experiment by physical modeling using Al alloy as a model material have been performed. Based on the results, the influence of fixed parameters on the distribution of divided material flow and surface expansion are obtained.