• 한국지반공학회지:지반
• /
• 제6권4호
• /
• pp.33-42
• /
• 1990

정적관입저항 또는 선단지지말뚝의 선단지지력을 해석함에 있어서는 유효수직응력이 기준음력으로 사용되어 왔다. 그러나 정적관입저항은 유효수직응력보다 원위치 유효수평응력에 관계된다는 것이 많은 실험연구결과로부터 보고 되었다. 이와같은 문제점을 규명하기 위하여 기 보고된 실험결과를 다시 분석하였으며 실험실에서의 관입시험이 실시되었다. 연구결과 정적관입저항은 유효수직 응력과 유효수평응력 모두에 영향을 받는 것으로 나타나고 있으며 해석시에는 평균주응력이 기준응력으로 사용되어야 함을 결론 지을 수 있었다.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.203-209
• /
• 2018

Reliable estimation of compressive as well as tensile in-situ stresses is critical in the design and analysis of underground structures and openings in rocks. Kaiser effect technique, which uses acoustic emission from rock specimens under cyclic load, is well established for the estimation of in-situ compressive stresses. This paper investigates the Kaiser effect on marble specimens under cyclic uniaxial compressive as well as cyclic uniaxial tensile conditions. The tensile behavior was studied by means of Brazilian tests. Each specimen was tested by applying the load in four loading cycles having magnitudes of 40%, 60%, 80% and 100% of the peak stress. The experimental results confirm the presence of Kaiser effect in marble specimens under both compressive and tensile loading conditions. Kaiser effect was found to be more dominant in the first two loading cycles and started disappearing as the applied stress approached the peak stress, where felicity effect became dominant instead. This behavior was observed to be consistent under both compressive and tensile loading conditions and can be applied for the estimation of in-situ rock stresses as a function of peak rock stress. At a micromechanical level, Kaiser effect is evident when the pre-existing stress is smaller than the crack damage stress and ambiguous when pre-existing stress exceeds the crack damage stress. Upon reaching the crack damage stress, the cracks begin to propagate and coalesce in an unstable manner. Hence acoustic emission observations through Kaiser effect analysis can help to estimate the crack damage stresses reliably thereby improving the efficiency of design parameters.

• Structural Engineering and Mechanics
• /
• 제18권5호
• /
• pp.541-563
• /
• 2004

For reaching large inelastic deformations without a substantial loss in strength, the potential plastic hinge regions of the reinforced concrete structural members should be confined by adequate transverse reinforcement. Therefore, simple and realistic representation of confined concrete behaviour is needed for inelastic analysis of reinforced concrete structures. In this study, a trilinear stress-strain model is proposed for the axial behaviour of confined concrete. The model is based on experimental work that was carried out on nearly full size specimens. During the interpretation of experimental data, the buckling and strain hardening of the longitudinal reinforcement are also taken into account. The proposed model is used for predicting the stress-strain relationships of confined concrete specimens tested by other researchers. Although the proposed model is simpler than most of the available models, the comparisons between the predicted results and experimental data indicate that it can represent the stress-strain relationship of confined concrete quite realistically.

• International Journal of Safety
• /
• 제2권1호
• /
• pp.23-27
• /
• 2003

Recently, continuous fiber reinforced ceramic composite(CFCC) has attracted attention to a number of engineers because of its significant benefit for several industrial area. This work was conducted to provide a basic characteristic of CFCC for tensile loading condition. The numerical analysis by general purpose finite element program was accomplished and compared with an experimental tensile test. The stress strain curves were expressed well by the numerical analysis and the first matrix cracking stress was in accordance with that of the experimental result. Moreover, fracture pattern was shown by kill command graphically.

• Structural Engineering and Mechanics
• /
• 제58권2호
• /
• pp.217-230
• /
• 2016

Effects of temperature dependent material properties on mixed mode fracture parameters of functionally graded materials subjected to thermal loading are investigated. A domain form of the $J_k$-integral method including temperature-dependent material properties and its numerical implementation using finite element analysis is presented. Temperature and displacement fields are calculated using finite element analysis and are used to compute mixed mode stress intensity factors using the $J_k$-integral. Numerical results indicate that temperature-dependency of material properties has considerable effect on the mixed-mode stress intensity factors of cracked functionally graded structures.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.123-128
• /
• 1998

In fracture problems, stress intensity factors obtained theoretically and experimentally have been effectively utilized in the analytical evaluation of the cracks effect. The effect of surface crack of a cylindrical and a hollow cylindrical bar is investigated, as well as the effect of the thickness of a hollow cylindrical bar and inclined crack of a hollow cylinder subjected to torsion moment. In this study, stress intensity factor Km of mode III which expresses the stress state in the neighborhood of a crack tip is used. Stress analysis was conducted of the inside of a hollow cylinder in the axial direction of three dimensional crack tip subjected to torsion moment by combining the caustics method and the stress freezing method.

• 한국생산제조학회지
• /
• 제7권5호
• /
• pp.46-52
• /
• 1998

In fracture problems, stress intensity factors obtained theoretically and experimentally have been effectively utilized in the analytical evolution of the cracks effect. The effect of surface crack of a cylindrical and a hollow cylindrical bar is investigated, as well as the effect of the thickness of a hollow cylindrical bar and inclined crack of a hollow cylinder subjected to torsion moment. In this study, stress intensity factor Km of mode III which expresses the stress state in the neighborhood of a crack tip is used. stress analysis was conducted on the inside of hollow cylinder inthe axial direction of three dimensional crack tip subjected to torsion moment by combining the caustics method and the stress freezing method.

• 한국해양공학회지
• /
• 제17권6호
• /
• pp.65-71
• /
• 2003

Since the preflex beam is fabricated through welding, the pre-compressive stresses that should occur over the concrete pier are diminished by the welding residual stresses. Therefore welding residual stresses must be relieved during the fabrication. Therefore, the analysis and examination of the accurate welding residual stress distribution characteristics are necessary. In this study, accurate distribution of welding residual stress of the preflex beam is analyzed by the finite element method, using 2 dimensional and 3 dimensional elements. Further, the thermo-mechanical behavior of the preflex beam is also studied. After the finite element analysis, real distribution of welding residual stress is measured using the sectioning method, and then is compared with the simulation results. The distribution of welding residual stress by finite analysis agreed well with the experimental results.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.233-236
• /
• 1999

The welding residual stress should be considered in fatigue stress analysis because it develope during the process of the electric resistance spot welding and it causes bad affect on the fatigue crack initiation and growth at nugget edge of spot welded points. Therefore the accurate estimation of residual stress is crucial. In this study, nonlinear finite element analysis on welding residual stress generated during the process of the spot welding was conducted, and their results were compared with the experimental data measured by X-ray diffraction method. From the results, it was found that welding residual stress existed as tension in the nugget center and as compression around the nugget edge.

• Journal of Mechanical Science and Technology
• /
• 제14권4호
• /
• pp.401-407
• /
• 2000

An elastic-plastic finite element analysis is performed to investigate detailed closure behavior of fatigue cracks and the numerical results are compared with experimental results. The finite element analysis performed under plane stress using 4-node isoparametric elements can predict fatigue crack closure behavior. The mesh of constant element size along crack surface can not predict the opening level of fatigue crack. The crack opening level for the constant mesh size increases linearly from initial crack growth. The crack opening level for variable mesh size, is almost flat after crack tip has passed the monotonic plastic zone. The prediction of crack opening level using the variable mesh size proportioning the reversed plastic zone size with the opening stress intensity factors presents a good agreement with the experimental data regardless of stress ratios.