• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1355-1360
• /
• 2008

Stainless steel sheets are widely used as the structure material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. Gas welding is very important and useful technology in fabrication of an railroad car and vehicles structure. However fatigue strength of the gas welded joints is considerably lower than parent metal due to stress concentration at the weldment, fatigue strength evaluation of gas welded joints are very important to evaluate the reliability and durability of railroad cars and to establish a criterion of long life fatigue design. In this paper, ${\Delta}P-N_f$ curve were obtained by fatigue tests. Using these results, the accelerated life test (ALT) is conducted. From the experimental results, an acceleration model is derived and acceleration factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of plug and ring gas welded joints and data analysis by statistic reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.

• 보존과학연구
• /
• s.30
• /
• pp.125-136
• /
• 2009

Stone cultural heritages in Korea have a severe damages from chemical and biological weathering because most of them have been situated in outdoors without any suitable protection systems, and this in turn causes deformation and structural damage. To counteract these problems and increase durability, various kinds of conservation materials are used in the conservation and restoration treatments. However until now there are not many practical and technological experiments on this subject. This paper attempts quantitative evaluation of effectiveness about chemical of ethylsilicate based resin for sandstone in Yeongyang-gun. It takes a long time to evaluate durability and side effect after conservation materials treatment. So we use artificial weathering through freezing§ thawing experimental method. As a result of this experiment, porosity and absorptance increased, and elastic wave speed, elastic modules, unconfined compression strength and tensile strength decreased more than before. This study plans to make a scientific method study about weathering factor and mechanism, and to deduce correlation between artificial weathering and natural weathering.

• Ocean and Polar Research
• /
• v.32 no.4
• /
• pp.475-482
• /
• 2010

Hydrothermal deposits on deep-sea floors are expected to provide potential metal resources for future demands. Korea was recently granted a prospecting licence to undertake exploration for hydrothermal metal deposits in the exclusive economic zone (EEZ) of the Kingdom of Tonga in the Pacific Ocean. The Korean Deep Seabed Mining Group (KDSMG), which consists of four Korean companies involved in marine technologies, oil and gas shipping, and smelter industries, has conducted research to evaluate the region's resource potential in cooperation with the Ministry of Land, Transport and Maritime Affairs (MLTM) of Korea. Here we present and reflect on the exploration results of these companies and their strategic plans. We also evaluate Research and Development (R&D) progress for the commercial development of seafloor hydrothermal deposits. Our own strategies and prospects for the commercial development of this potential resource are also outlined. We do acknowledge that other potentially important information regarding the amount of ore body, the inside structure, and the metal yields have not yet been clarified sufficiently. As such it is necessary to address these problems through experimental R&D and surveys.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.77-85
• /
• 2010

Stainless steel sheets are widely used as the structure material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. Gas welding is very important and useful technology in fabrication of a railroad car and vehicles structure.However fatigue strength of the gas welded joints is considerably lower than parent metal due to stress concentration at the weld, fatigue strength evaluation of gas welded joints are very important to evaluate the reliability and durability of railroad cars and to establish a criterion of long life fatigue design. In this paper, $({\Delta}{\sigma}_a)_R-N_f$ curve were obtained by fatigue tests. Using these results, the accelerated life test(ALT) was conducted. From the experimental results, an acceleration model was derived and acceleration factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of plug and ring gas welded joints and data analysis by statistic reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.

• Journal of Korean Home Economics Education Association
• /
• v.12 no.3
• /
• pp.115-127
• /
• 2000

The purpose of this study is to develop lesson plans. teaching guide, and teaching materials applying practical reasoning teaching model in the area of ’human development and family relationship’in middle school home economics. The practical reasoning teaching model consists of five factors: Desired results, Awareness of context, Alternative approaches, Consequences of action, and Action. This study based on practical reasoning has following process: Curriculum development. Developing lesson pan, teaching material, an teaching guide, Experimental teaching and evaluation. Feedback, Production of CD-Rom. Teaching guide includes lesson plan, workbook multimedia materials and teaching resources. Especially teaching guide in CD-Rom can be used effectively in the actual teaching. In the classroom, this teaching model accomplished active and interesting participation of teachers and students. It is proposed that practical reasoning teaching model should be applied to other areas of home economics. In addition various teaching materials based on practical reasoning need to developed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.1-8
• /
• 2011

Stainless steel sheets are widely used as the structure material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. Gas welding is very important and useful technology in fabrication of an railroad car and vehicles structure. However fatigue strength of the gas welded joints is considerably lower than parent metal due to stress concentration at the weldment, fatigue strength evaluation of gas welded joints are very important to evaluate the reliability and durability of railroad cars and to establish a criterion of long life fatigue design. In this paper, ${\Delta}-N_f$ curve were obtained by fatigue tests. Using these results, the accelerated life test (ALT) is conducted. From the experimental results, an acceleration model is derived and acceleration factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of plug and ring gas welded joints and data analysis by statistical reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.

• Korea Journal of Hospital Management
• /
• no.spc
• /
• pp.1-13
• /
• 2016

In a situation where competition becomes intense, health care organizations constantly strive to provide more services with given personnel and time. While not only the 'quantity' of the services but also the 'quality' becomes increasingly important, various problems that can occur during the 'process' of service provision can be effectively managed by applying the methods of management science. In this study, we introduce the cases where the methods of management science can be applied for the management of health care organizations in Korea and abroad. There are many cases where various scenarios for improving the patients' accessibility to the services and for maximizing the efficient use of limited resources are established, and simulation or basic statistical analysis methods are used to solve the problems more systematically or to develop improvement plans. In this study, several exemplary cases, such as no-show of patients, crowding in the emergency room, prediction of the number of available beds in the intensive care units, nurse scheduling, delay of arrival of patients, and ordering of the proper amount of therapeutic materials, are introduced and discussed. From the perspective of administrators or clinicians, however, it may not be easy to master the methodology that requires considerable mathematical background or apply the theories to practice directly. Therefore, it is suggested that more practical and relatively simple analytical methods should be applied. Also, having a more positive attitude toward improving the current performance (e.g., a belief that 'we can always be better than now'), and paying attention to improving the job satisfaction by addressing problems, with experimental spirit and data-driven decision management.

• Smart Structures and Systems
• /
• v.12 no.5
• /
• pp.523-545
• /
• 2013

Piezoelectric and dielectric behaviors of a piezoceramic patch adhesively centered on a carbon composite plate are identified using a robust multi-objective optimization procedure. For this purpose, the patch piezoelectric stress coupling and blocked dielectric constants are automatically evaluated for a wide frequency range and for the different identifiable behaviors. Latters' symmetry conditions are coded in the design plans serving for response surface methodology-based sensitivity analysis and meta-modeling. The identified constants result from the measured and computed open-circuit frequencies deviations minimization by a genetic algorithm that uses meta-model estimated frequencies. Present investigations show that the bonded piezoceramic patch has effective three-dimensional (3D) orthotropic piezoelectric and dielectric behaviors. Besides, the sensitivity analysis indicates that four constants, from eight, dominate the 3D orthotropic behavior, and that the analyses can be reduced to the electromechanically coupled modes only; therefore, in this case, and if only the dominated parameters are optimized while the others keep their nominal values, the resulting piezoelectric and dielectric behaviors are found to be transverse-isotropic. These results can help designing piezoceramics smart composites for various applications like noise, vibration, shape, and health control.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.2
• /
• pp.155-162
• /
• 2009

In walking guide robot, a guide vehicle detects an obstacle distribution in the walking space using range sensors, and generates a 3D grid map to map the obstacle information and the tactile display. And the obstacle information is transferred to a blind pedestrian using tactile feedback. Based on the obstacle information a user plans a walking route and controls the guide vehicle. The algorithm for 3D detection of an obstacle distribution and the method of mapping the generated obstacle map and the tactile display device are proposed in this paper. The experiment for the 3D detection of an obstacle distribution using ultrasonic sensors is performed and estimated. The experimental system consisted of ultrasonic sensors and control system. In the experiment, the detection of fixed obstacles on the ground, the moving obstacle, and the detection of down-step are performed. The performance for the 3D detection of an obstacle distribution and space mapping is verified through the experiment.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.4
• /
• pp.309-314
• /
• 2010

Stainless steel stamping multistage pump has become the mainstream of civil multi-stage pump. Combined with the technological features of stamping and welding pump, the studies of design for hydraulic parts of pump were come out. An $L_{18}$（$3^7$）orthogonal experiment was designed with seven factors and three values including blade inlet angle, impeller outer diameter, guide vane blade number, etc. 18 plans were designed. The two stage of whole flow field on stainless steel stamping multistage pump at design point for design was simulated by CFD. According to the test result and optimization design with experimental research, the trends of main parameters which affect hydraulic performance were got. After being manufactured and tested, the efficiency of the optimal model pump reaches 61.36% and the single head is more than 4.8 m. Compared with the standard efficiency of 53%, the design of the stainless steel stamping pump is successful. The result would be instructive to the design of Stainless steel stamping multistage pump designed by the impeller head maximum approach.