• Asian-Australasian Journal of Animal Sciences
• /
• 제14권10호
• /
• pp.1400-1404
• /
• 2001

$Holstein\;{\times}\;indigenous$ multiparous dairy cows were offered diets with increasing roughage neutral detergent fiber (NDF) contents to determine the effects on intake, milk yield and compositions. Roughage NDF contents were 15, 18, 21 and 24% dry matter (DM), and concentrate NDF content was 10% DM. Experimental treatments were isonitrogenous and isocaloric diets. Maximum and minimum temperature humidity index during the experimental period were 85.9 and 76, respectively. Intakes of DM, crude protein and net energy, 4% fat corrected milk, milk protein and average daily gain decreased with increasing roughage NDF contents (p<0.05). Intakes of ether extract (p<0.01) and dietary NDF (p>0.05) and milk fat (p<0.01) increased with increasing roughage NDF contents. The results support the conclusion that higher DM intake, optimal milk yield and compositions can be maintained with lower roughage NDF diets for dairy cows under tropical conditions.

• Journal of Astronomy and Space Sciences
• /
• 제14권2호
• /
• pp.269-274
• /
• 1997

Langmuir probe was housed in the sounding rocket to test the probe's performance and to find the environmental parameters at the F layer of the ionosphere. The gold plated cylindrical probe had a length of 14㎝ and a diameter of 0.096 ㎝. The applied voltage to the probe consisted of 0.9 sec fixed positive bias followed by 0.1 sec of down/up sweep. This ensured that the probe swept through the probe's current-voltage characteristic at least once during 1 second quiescent periods enabling the electron temperature to be measured during the undisturbed times of the flight. The experimental results showed good agreement of the temperature distribution with IRI model at the lower F layer. In the upper layer, the experimental temperatures were 100-200K lower than the IRI model's because of the different geomagnetic conditions: averaged conditions were used in IRI model and specific conditions were reflected in the experiment.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.115-119
• /
• 2008

Weld line in injection molded part is one of the defects in injection molding process. Weld line deteriorates not only appearance quality but mechanical property. In this study, ABS and PP were used as experimental materials. And weld line length, depth and strength have been examined according to the injection molding conditions. As the results of experimental studies, weld line length increased as flow rate increases for all materials. And the flow rate is most influenced to the creation of weld line length. Also weld line strength increased, as flow rate and melt temperature increase for all materials. The whole experiment results was similar to CAE analysis results.

• 설비공학논문집
• /
• 제3권1호
• /
• pp.78-85
• /
• 1991

An experimental result for heat transfer of pulsating turbulent pipe flow was presented under the condition of fully developed dynamic regime and uniform wall heat flux. Experiments were performed at following conditions ; Inlet time-averaged Reynolds number varied from 5000 to 11000; The peak pressure fluctuation were 1.3, 2.3 and 3.5 percent of the mean pressure; Pulsating frequency ranged from 53 Hz to 320 Hz The measurements showed that the effect of pulsation on local heat transfer is greater at downstream, in which pulsating source exists, than upstream and the heat transfer rate, averaged over the pipe length, was higher or lower than in an equivalent non-pulsating flow according to the pulsating conditions. In addition, the significant change of heat transfer rate was observed in acoustically resonant conditions, when the pulsating frequency of the flow corresponded to the pipe natural frequency.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.277-281
• /
• 2008

This paper presents the development of a high efficiency transport refrigeration system for sliced-raw fish transportation. The refrigeration system is equipped with heat storage for reverse cycle-hot gas defrost (the stored heat is used during defrost cycle of the system). System performance and container operating conditions are analyzed during experimental investigation on a $3,225{\times}1,740{\times}1,640\;mm$ full-scale refrigerated container under cooling and defrosting conditions. The prototype system indicates better performance in terms of shorter cooling-down time, shorter defrost time and smaller fluctuations of refrigerated container's temperature.

• 약학회지
• /
• 제45권1호
• /
• pp.23-28
• /
• 2001

Hydrotalcite was prepared by reacting with sodium carbonate, magnesium hydroxide and aluminum chloride solutions in this study. The optimum synthesis conditions based on the yield of the product were established by applying Box-Wilson experimental design. It was found that the optimum synthesis conditions of hydrotalcite were as follows ; reacting temperature : 63~9$0^{\circ}C$, concentration of reactant solution : 18.20~19.82%, molar concentration ratio of two reactants [Mg(OH)$_2$] / (AICl$_3$.6$H_2O$) : 6.0, temperature of washing water : 29.0-34.4$^{\circ}C$, drying temperature : 56-77.6$^{\circ}C$. The physicochemical properties of hydrotalcite as medicine were studied by use of chemical analysis, bulk volume test and acid consuming capacity measurements.

• 설비공학논문집
• /
• 제8권1호
• /
• pp.45-54
• /
• 1996

An experimental investigation on the two-phase flow through tube orifices was performed with the refrigerant mixture of R32/125/134a(30/10/60). A series of tests were conducted to generate wide range of data at varying operation conditions with four short tubes. The tests include both single and two-phase flow conditions at the inlet of the short tube with different oil concentrations. Experimental data were presented as a function of major operating parameters and short tube diameter. Based on test results and data analysis, a semi-empirical flow model was developed to predict the mass flow rate through short tube orifices with a given set of conditions. The flow model was formed to cover both single and two-phase flow at the inlet of short tube with considering the effects of oil concentration.

• International Journal of Concrete Structures and Materials
• /
• 제11권1호
• /
• pp.69-84
• /
• 2017

This paper presents results of an experimental investigation on the behaviour of bond between external glass fibre reinforced polymer reinforcement and concrete exposed to three different environmental conditions, namely, temperature cycles, wet-dry cycles and outdoor environment separately for extended durations. Single shear tests (pull-out test) were conducted to investigate bond strengths (pull-out strengths) of control (unexposed) and exposed specimens. Effect of the exposure conditions on the compressive strength of concrete were also investigated separately to understand the effect of changing concrete compressive strength on the pull-out strength. Based on the comparison of experimental results of exposed specimens to control specimens in terms of bond strengths, failure modes and strain profiles, the most significant degradation of pull-out strength was observed in specimens exposed to outdoor environment, whereas temperature cycles did not cause any deterioration of strength.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.124-129
• /
• 2001

The experimental study was the cutting characteristics of non-ferrous metals. The experimental apparatus was used the turning machine and diamond tool. This aimed at lading the optimal cutting conditions by measuring surface farm and roughness. Used non-ferrous metals were aluminum, brass and oxygen-free copper. As well, according to changing cutting conditions such as feed rate by measuring cutting farce and surface roughness and according to cutting conditions the non-ferrous metals studied about cutting properties.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.114-120
• /
• 2008

This study is to compare and analyze the material flow, deformation characteristics, and forming load of flange by means of similitude experimental method of model material using plasticine. In order to find optimal forming conditions, prototype experiments were designed to investigate forming characteristics of general-purpose flange under various working conditions. As a result of prototype experiments, billet thickness and gap-height ratio was found to be the most influential experimental parameter in flange forming. Forming loads from prototype experiments were compared to the results of finite element analysis after conducting estimation of forming loads of real material. Results of prototype experiments based on model material techniques are expected to be used as a basic data of die design f3r the development of products and process.