• Journal of Power Electronics
• /
• v.13 no.5
• /
• pp.861-876
• /
• 2013

Instead of extracting every selected harmonic component, the current reference of selective active power filter (APF) can be also obtained by filtering out the fundamental component from distorted load current for computation efficiency. This type of mixed current reference contains kinds of harmonic components and easily involves noises. In this condition, selective harmonic compensation must be realized by the current controller. With regard that selectivity is the most significant feature of controller, this paper presents specific comparison analysis between two types of resonant controllers: proportional-resonant (PR) controller and vector-resonant (VR) controller. The comparison analysis covers the relations, performances, and stability of both controllers. Analysis results conclude that the poorer selectivity of the PR controller could be relatively improved, but limitations from system stability make the improvement hardly realized. By contrast, the VR controller exhibits excellent selectivity and is more suitable for selective APF with mixed current reference. Experimental results from laboratory prototype validate the reasonability of analysis. And the features of each resonant controller are concluded.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8C
• /
• pp.497-504
• /
• 2011

This paper presents an adaptive retinex algorithm, In order to solve typical problems of retinex algorithm such as expensive computational cost, halo artifact, and color distortion, a function of skewness that represents a statistical distribution of pixels is defined to compensate contrast and color distortion. The experimental results show that the proposed algorithm leads to subjectively better performance than typical retinex algorithm, and that the proposed algorithm has the capability to reduce approximately 40% computational cost than typical retinex algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.9
• /
• pp.1297-1305
• /
• 2015

This paper proposes a power feedforward technique for the performance improvement of DC-link voltage control in the dynamic voltage restorer (DVR). The DC-link Voltage is able to be unstable for an instant owing to any change in the load and voltage sag. The distortion of the DC-link voltage leads to the negative influence on the performance of DVR. To mitigate the distortion of the DC-link voltage, the power feedforward component is calculated by the load power and the grid voltage, and then it is added to the reference current of the conventional DC-link voltage controller. By including output power feedforward component on the DC-link controller, the DC-link voltage can settle down more quickly than when the conventional DC-link voltage controller applied. The proposed technique was validated through the simulation and experimental results.

• Journal of IKEEE
• /
• v.2 no.2 s.3
• /
• pp.285-293
• /
• 1998

This paper presents unequal error protection and error concealment techniques far robust H.263 video transmission over mobile channels. The proposed error protection scheme has three major features. First, it has the capability of preventing the loss of synchronization information in H.263 video stream as much as possible that the H.263 decoder can resynchronize at the next decoding point, if errors are occurred. Secondly, it employs an unequal error protection scheme to support variable coding rates using rate compatible punctured convolutional (RCPC) codes, dividing the encoded stream into two classes. Finally, a macroblock-interleaving scheme is employed in order to minimize the corruption of consecutive macroblocks due to burst errors, which can make a proper condition for error concealment. In addition, to minimize the spatial error propagations due to the variable length codes, a fast resynchronization scheme at the group of block layer is developed for recovering subsequent error-free macroblocks following the damaged macroblock. futhermore, error concealment techniques based on both side match criterion and overlapped block motion compensation (OBMC) are employed at the source decoder so that it can not only recover the lost macroblock more accurately, but also reduce blocking artifacts. Experimental results show that the proposed scheme can be an effective error protection scheme since proper video quality can be maintained under various channel bit error rates.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.379-388
• /
• 2002

In this paper, the real-time algorithm is proposed for automatic detection of the face and facial features. In the face region, we extracted eyes, nose, mouth and so forth. There are two methods to extract them; one is the method of using the location information of them, other is the method of using Gaussian second derivatives filters. This system have high speed and accuracy because the facial feature extraction is processed only by detected face region, not by whole image. There are some kinds of good experimental result for the proposed algorithm; high face detection rate of 95%, high speed of lower than 1sec. the reduction of illumination effect, and the compensation of face tilt.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.77-82
• /
• 2006

Analog channel selection filter is described which is designed for a direct-conversion receiver of a IEEE 802.11a wireless LAN. The channel selection filter is an active-RC fifth-order Chebyshev filter with 10MHz cut-off frequency. Two-stage operational amplifier of the filter employs a current re-using feedforward frequency compensation scheme to minimize the power consumption. The filter has been implemented in a 0.18mm CMOS technology and the experimental results show 20mW power consumption with 1.8V supply voltage and 19dB out-of-band iIP3.

• ETRI Journal
• /
• v.31 no.1
• /
• pp.21-30
• /
• 2009

In low bit-rate video transmission, the payload of a single packet can often contain a whole coded frame due to the high compression ratio in both spatial and temporal domains of most modern video coders. Thus, the loss of a single packet not only causes the loss of a whole frame, but also produces error propagation into subsequent frames. In this paper, we propose a novel whole frame error concealment algorithm which reconstructs the first of the subsequent frames instead of the current lost frame to suppress the effects of error propagation. In the proposed algorithm, we impose a constraint which uses side match distortion (SMD) and overlapped region difference (ORD) to estimate motion vectors between the target reconstructed frame and its reference frame. SMD measures the spatial smoothness connection between a block and its neighboring blocks. ORD is defined as the difference between the correlated pixels which are predicted from one reference pixel. Experimental results show that the proposed algorithm effectively suppresses error propagation and significantly outperforms other conventional techniques in terms of both peak signal-to-noise ratio performance and subjective visual quality.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.694-704
• /
• 1988

A recursive parameter estimation scheme utilizing the variance perturbation method is applied to the workpiece deflection model during CNC turning process, in order to improve the cylindricity of slender workpiece. It features that it is based on exponentially weighted recursive least squares method with post-process measurement of finish surfaces at two locations and it does not require a priori knowledge on the time varying deflection model parameter. The measurements of finish surfaces by using two proximity sensors mounted face to face enable one to identify the straightness, guide-way, run-out eccentricity errors. Preliminary cutting tests show that the straightness error of the finish surface due to workpiece deflection during cutting is most dominant. Identifying the errors and recursive updating the parameter, the off-line control is carried out to compensate the workpiece deflection error, through single pass cutting. Experimental results show that the proposed method is superior to the conventional multi-pass cutting and the direct compensation control in cutting accuracy and efficiency.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.10 no.1
• /
• pp.13-23
• /
• 2015

Recently, a few image-processing based mobile urine testers have actively been studied since the urine-analysis result can be available to the user in real time immediately after the test is done. However, the accuracy of test result can be severely degraded due to variable illumination environments and a variety of manners to capture the image with a camera embedded in the smartphone according to different users. This paper proposes the Check4Urine system, a novel smartphone-based portable urine-analysis tester and provides three techniques to improve such a performance degradation problem robust to various test environments and disturbances, which are the compensation algorithm to correct the varying illumination effect, an urine strip detection algorithm robust to edge loss of the object image, and the color decision algorithm based on the pre-processed reference table. Experimental results show that the proposed Check4Urine system increases the accuracy of urine-analysis by 20-50% at various test conditions, compared with the existing image-processing based mobile urine tester.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.5
• /
• pp.453-458
• /
• 2015

We presented a quad-rotor controlling algorithm design by using sensor fusion in this paper. The controller design technique was performed by a PD controller with a Kalman filter and compensation algorithm for increasing the stability and reliability of the quad-rotor attitude. In this paper, we propose an attitude estimation algorithm for quad-rotor based sensor fusion by using the Kalman filter. For this reason, firstly, we studied the platform configuration and principle of the quad-rotor. Secondly, the bias errors of a gyro sensor, acceleration and geomagnetic sensor are compensated. The measured values of each sensor are then fused via a Kalman filter. Finally, the performance of the proposed algorithm is evaluated through experimental data of attitude estimation. As a result, the proposed sensor fusion algorithm showed superior attitude estimation performance, and also proved that robust attitude estimation is possible even in disturbance.