• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.705-710
• /
• 2001

So for the quartz-glassy crucible wastes which was used for pulling up silicon-single-crystal ingot have simply reused for refractory raw-materials, or exhausted. This study is concerned on the advanced recycling-technology that is obtained by the proper micro-particle preparation process in order to fabricate fine amorphous silica filler for EMC (Epoxy Molding Compound). Therefore, this paper will deal with the physical, chemical and thermal pre-treatment process for efficient impurity removal and with the proper micro-particle process for producing the amorphous silicafiller. In view of the results, if the chemical, physical and thermal pre-treatment process for efficient elimination of impurity was passed, the purity of wasted fused glassy crucible is almost equal to the its of first anhydrous quartz glass. Thus, it was understood that this wasted fused glassy crucible was sufficient value of recycling, though it was damaged. When the ingot was fabricated, Phase transformation of crystallization by heat treatment (heat hysteresis phenomenon) was not changed. So, it was understood that as fused silica in the amorphous state, as It is, recycling possibility was very high

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.246-249
• /
• 2007

A triple-band antenna was developed and fabricated by LDS(Laser Direct Structuring) process. The effects of the plating rate and heat treatment condition were investigated and the gains of fabricated antennas were measured at various frequencies. The laser irradiated surface shows clearly that there are prominence and depression. It shows anchoring effect between a plating material and ablation surface. The plating rate was decreased when the plating material is exhausted in the solution. This solution needs to refreshed by the new aid solution. The copper plating thickness is decreased with the increase of heat treatment temperature in the same time but it does not change other condition. The gain of LDS antenna showed higher than the generally processed antenna. This result was related with practical use of the dimension and effective dielectric constant.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.116-124
• /
• 2007

An adsorption chiller is expected to have high energy-efficiency in utilizing the waste heat exhausted from a process. The objective of this paper is to investigate the performance of silica gel-water adsorption chiller from the cycle simulation and to provide a guideline for design of the adsorption chiller. The effect of cycle time, inlet temperature and water flow rate on the cooling capacity and COP is quantified during the cycle operation. It is found that the performance of adsorption chiller is more sensitive to the change of inlet water temperature rather than the water flow rate. It is concluded that the COP is 0.57 in the standard conditions(hot water $80^{\circ}C$, cooling water $30^{\circ}C$, chilled water inlet temperatures $14^{\circ}C$ and cycle time 420sec).

• 한국안전학회지
• /
• 제17권4호
• /
• pp.119-125
• /
• 2002

The concept of dwelling space is tend to be changed not only to have reasonable mobility but also to have high quality of indoor air with psychologicaa satisfaction and comfortable. Moreover, recent constructed buildings have a big problem because of exhausted pollution gas and particles from building materials. More serious problem occurs from its high air tightness reducing the ventilation for saving the energy and superior adiabatic insulators to have high heat efficiency. Indoor air quality in super high-rise dwelling house was investigated by measuring pollutants such as $CO_2,=;CO,\;MO_2,\;R_n,\;TSP,\;PM_{10}$, HCHO, Offensive ordor. Subjective evaluation of residential environment is processed for the inhabitants who live in research space by testing environmental load in accordance with environment morphology, exterior environmental factor and post occupancy correlation and influence of attention.

• 한국입자에어로졸학회지
• /
• 제9권3호
• /
• pp.163-171
• /
• 2013

Soot particles emitted from combustion processes are often coated by non-absorbing organic materials, which enhance the global warming effect of soot particles. It is of importance to study the condensation characteristics of soot particles experimentally and theoretically to reduce the uncertainty of the climate impact of soot particles. In this study, the condensational growth of soot particles in a tubular coater was modeled by a one-dimensional (1D) plug flow model and a two-dimensional (2D) laminar flow model. The effects of 2D heat and mass transports on the predicted particle growth were investigated. The temperature and coating material vapor concentration distributions in radial direction, which the 1D model could not accounted for, affected substantially the particle growth in the coater. Under the simulated conditions, the differences between the temperatures and vapor concentrations near the wall and at the tube center were large. The neglect of these variations by the 1D model resulted in a large error in modeling the mass transfer and aerosol dynamics occurring in the coater. The 1D model predicted the average temperature and vapor concentration quite accurately but overestimated the average diameter of the growing particles considerably. At the outermost grid, at which condensation begins earliest due to the lowest temperature and saturation vapor concentration, condensing vapor was exhausted rapidly because of the competition between condensations on the wall and on the particle surface, decreasing the growth rate. At the center of the tube, on the other hand, the growth rate was low due to high temperature and saturation vapor concentration. The effects of Brownian diffusion and thermophoresis were not high enough to transport the coating material vapor quickly from the tube center to the wall. The 1D model based on perfect radial mixing could not take into account this phenomenon, resulting in a much higher growth rate than what the 2D model predicted. The result of this study indicates that contrary to a previous report for a thermodenuder, 2D heat and mass transports must be taken into account to model accurately the condensational particle growth in a coater.

• 대기
• /
• 제22권4호
• /
• pp.465-472
• /
• 2012

Using various observed data, we examined the evolution of tropical Pacific sea surface temperature (SST) during 2011-2012, with focusing on the development of 2012 El Ni$\tilde{n}$o. It is observed that a La Ni$\tilde{n}$a event during 2011 was followed by a moderate El Ni$\tilde{n}$o during 2012 summer. The 2012 summer El Ni$\tilde{n}$o initiated near the west coast of South America on February 2012, and continued to expand westward till August. Given this evolutionary pattern, the 2012 summer El Ni$\tilde{n}$o can be categorized as 'Eastern Pacific (EP) El Ni$\tilde{n}$o' because Ni$\tilde{n}$o-3 index is greater than Ni$\tilde{n}$o-4 index, and it may be the first well-defined EP El Ni$\tilde{n}$o since 2001. On February 2012, this event was initiated mainly by the local air-sea interaction, and at the same time the ocean heat content was accumulated over the tropical western Pacific due to the easterly wind anomaly over the tropical western Pacific. Then, the accumulated heat content slowly propagates to the tropical eastern Pacific, which attributes to maintain El Ni$\tilde{n}$o state during 2012 summer. After August, the positive SST anomaly over the equatorial eastern Pacific decays possibly due to the exhausted heat content and the weakening of air-sea interaction, but the weak positive SST anomaly over the central Pacific remains till now (2012 November).

• 한국산학기술학회논문지
• /
• 제16권6호
• /
• pp.3672-3679
• /
• 2015

열차 운행에 따른 전장품들의 발열을 예측하기 위해 동력차 내 벽면온도 및 외부 유출 온도 및 풍속, 외부로부터 유입되는 유입 공기의 유입 온도 및 속도를 측정하였다. 이를 위하여 적외선카메라를 이용하여 고속열차 내부의 전장품 및 벽 표면의 온도를 측정하였다. 또한 전장품에서 발생하는 열은 고속열차 천장에 설치된 덕트를 통하여 외부로 배출된다. 배출되는 공기의 온도 및 속도를 측정하였고, 외부에서 동력차 내부로 들어오는 유입공기의 온도 및 속도도 측정하였다. 또한 부착형 온도센서를 이용하여 동력차 내부의 벽 및 전장품 표면에서의 온도를 측정하였다. 측정된 결과를 이용하여 열차 주행에 따른 전장품의 발열 특성을 분석하였다.

• 대한기계학회논문집B
• /
• 제37권1호
• /
• pp.81-86
• /
• 2013

소형디젤 발전기의 배기가스는 양적 및 질적 수준에서 유용하게 활용되기에는 부족한 폐열원으로 간주된다. 그러나 본 연구에서는 이러한 배기가스의 폐열을 히트파이프에 의해 회수하고 다중효용확산 증발에 의해 효율적으로 열을 이용하는 해수담수기를 제안하였다. 제안한 증류기는 $171^{\circ}C$의 배기가스에서 52 W 의 폐열을 회수할 수 있고, 이 회수 열량 중 약 85%가 약 70 g/h의 담수를 생산할 수 있는 유용한 열량으로 사용된다. 이 결과는 50cc, 4 행정 엔진을 가진 극소형 발전기의 폐열에 대하여 단효용 장치의 실험값이므로, 10 중효용으로 구성할 경우 약 500 g/h 의 성능을 가질 수 있는 것으로 계산되었다. 따라서 본 증류기는 전기와 담수가 동시에 부족한 지역에서 실제 필요한 식수량을 확보할 수 있는 소용량 담수화장치로 유용하게 활용될 수 있다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.124.2-124.2
• /
• 2010

Generally, a coolant of the nuclear power plant is manufactured by electrolyzing the sea water near the plant for making the sodium hypochlorite(NaOCl), which is used for sterilizing the bacteria and the shellfishes sticking to the drains or the pumps at the outlet of the cooling system due to $8-10^{\circ}C$ warmer temperature than the inlet sea water. During manufacturing the sodium hypochlorite, the hydrogen with the high purity is also produced at the anode side of the electrolyzer. This paper describes a novel power plant system combined with the polymer electrolyte membrane(PEM) fuel cell, the wasted hydrogen from the sea water electrolyzer and the wasted heat of the nuclear power plant. The present status over the exhausted hydrogen at twenty nuclear power plants in Korea was investigated in this study, from which an available power generation is estimated. Furthermore, the economic feasibility of the PEM fuel cell power plant is also evaluated by a current regulations over the power production and exchange using a renewable energy shown in Korea Power Exchange(KRX).

• 설비공학논문집
• /
• 제10권4호
• /
• pp.475-482
• /
• 1998

In this paper, an experimental study was conducted to investigate the performance of the spherical ice particle production system which uses the technology of water spray in a vacuum chamber for increasing the heat transfer area. As a result, following conclusions were obtained. The diffusion-controlled evaporation model agreed relatively well with experiments. The spray flow rate influences the performance of the system rather than any other factors, for example, the spray nozzle position, the nozzle number. As the spray rate increases, the system efficiency increases. It is due to the entrainment of small droplets among the spray with the exhausted vapor. Thus the system should be designed and operated to prevent the entrainment. Assuming the compressor efficiency to be 70%, the COP of the system reaches highly up to 6 at a maximum spray rate. Under the conditions, however, the rigid ice layer is obtained because ice particles bond together with increase of the spray rate. Therefore, the spray rate should be controlled properly to make the spherical ice particles.