• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.49-61
• /
• 1983

U shape multitube heat exchanger was equipped in the flue to recover the exhaust heat from the boiler system. The fluids of the exhaust heat recovery equipment were the flue gas as the hot fluid, and the water as the cold fluid. The flow geometry of the fluids was cross flow - two pass, the hot fluid being mixed and the cold fluid unmixed. The results of the theoretical and the experimental analysis and the economic evaluation are summarized as follows. 1) The heat exchanger effectiveness and the temperature efficiency of the hot fluid were about 35% when the fuel consumption rate was 140 - 150 L/15min. The temperature efficiency for the cold fluid ranged from 3.0% to 4.5%. The insulation efficiency ranged from 85% to 98%, which was better than the KS air preheater insulation efficiency of 90%. 2) The relationship between the fuel consumption rate, F, and the outlet temperature, $T_{h2}$, of the flue gas from the heat exchanger was $T_{h2}$ = 0.927F + 110. In order to prevent the low temperature corrosion from the coagulation of $SO_3$, it is necessary to maintain the fuel consumption rate above 82 L/15min. 3) The ratio of the exhaust heat from the boiler system to the total energy consumption was about 14.5%. With the installation of the exhaust heat recovery equipment, the energy recovery ratio to the exhaust heat was about 25%. Accordingly, about 3.6% of the total fuel consumption was estimated to be saved. 4) Economic analysis indicated that the installation of the exhaust heat recovery equipment was feasible to save the energy, because the capital reocvery period was only 10 months when the fuel consumption rate was 80 L/15min. 4 months when it was 160 L/15min. 5) Based on the theoretical and the experimental analysis, it was estimated to save the energy of about 18 million Won per year, if four heat exchangers are installed in a factory. 6) A further study is recommended to identify the relationship among the flow rate of the exhaust gas, the size of the heat exchanger and the capacity of the air preheater. For a maximum heat recovery from the exhaust gas an automatic control system is required to control the flow rate of the cold fluid depending on the boiler load.

• 한국가스학회지
• /
• 제19권2호
• /
• pp.66-73
• /
• 2015

가솔린 엔진에서 개조된 가스 엔진에서 발생하는 냉각수와 배기가스를 분석하여 복합발전 시스템에서 활용 가능한 폐열의 양과 질을 확인하였다. 엔진 배기가스의 온도는 $573.8^{\circ}C$이고, 엔진 출구 냉각수의 온도는 $85.7^{\circ}C$이고, 폐열의 양은 엔진 냉각수가 배기가스에 비교하여 두 배 수준이었다. 두 가지 폐열의 상이한 온도와 양에 대응하는 유기랭킨사이클 (Organic Rankine Cycle: ORC) 발전시스템을 설계하고 열역학적 분석을 수행하였다.

• 한국해양공학회지
• /
• 제33권5호
• /
• pp.479-485
• /
• 2019

As exhaust gas systems of ships become more complicated, it is necessary to calculate an accurate pressure loss at their design stage. If the dynamic loss coefficients of non-standard fittings mainly used in exhaust gas pipe (EGP) are well-documented, it would be possible to calculate precise pressure loss more readily than using the conventional method that analyzes the entire system. In the case of a ship's EGP, the flow rates and temperatures of exhaust gas are determined by engine specifications, and the range of the flow rate and temperature is limited according to operating conditions. In addition, as it is possible to define non-standard fittings frequently used in an EGP, a database can be easily constructed and effective. This paper illustrates effective parameters and analysis cases of several types of non-standard fittings mounted in ship EGPs. The analysis procedure proposed in this paper is verified using existing research results on HVAC fittings. The numerical procedure, which is minimally affected by manpower and grid, is established such that it can be applied at the industry level.

• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.205-212
• /
• 1998

Experiments were conducted to investigate the temperature profile and the emissions conversion efficiency of catalytic converters for natural gas vehicles. Two types of the catalyst structure and several transient engine operating conditions were used. The dual-bed catalyst effectively reduced the emissions in a transient period due to the low heat capacity of the front bed. The lanthanoid additives were effective in improving catalyst durability. When the natural gas fueled engine were operated outside of a very narrow window of excess air ratio (from 0.993 to 1.004), the HC and NOx conversion efficiency dropped off. The drop-off were especially fast on the lean side of the window.

• 한국가스학회지
• /
• 제21권3호
• /
• pp.53-60
• /
• 2017

연소로에서 질소산화물을 저감하기 위하여 여러 가지 방법으로 연구가 진행되어 오고 있는데 그 중에 배기가스를 재순환하여 저감하는 방법이 있다. 본 연구는 배기가스를 재순환하는 방법으로 연소로 외부에 코안다 노즐을 이용하여 배기가스를 재순환 유입하는 방법을 사용하였다. 코안다 노즐을 이용하여 배기가스를 재순환하고 혼합가스는 연소로 접선 방향으로 투입하여 선회유동을 유발하는 특징을 가지는 배기가스 재순환 버너이다. 이러한 버너에서 연소로 내의 선회 유동 특성을 살펴보고 온도와 반응속도 분포를 살펴봄으로써 코안다 노즐을 이용한 재순환 버너의 연소 유동 특성을 규명하였다. 과잉공기계수와 코안다 노즐 간격을 변화하여 배기가스 재순환 유입량 특성을 살펴보았으며 과잉공기계수를 증가하면 재순환 유입량비가 증가하였고 코안다 노즐 간격을 증가하면 코안다 노즐 공기 출구에서 속도가 낮아져서 재순환 유입량이 감소한다는 특성을 알았다. 배기가스 출구에서 평균온도는 코안다 노즐 간격 변화에 거의 무관하며 과잉공기계수 증가에 따라 감소하는 것을 알았다. 이러한 특성으로 배기가스 출구에서 NOx 농도는 과잉공기계수 증가에 따라 현저히 감소하고 코안다 노즐 간격에는 상대적으로 영향이 적은 것으로 나타났다.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.95-103
• /
• 1999

Experimental study on combustion characteristics of a regenerative combustor has performed. High-temperature air combustion in the regenerative combustor is obtained through heat recovery from exhaust gas flow by porous ceramic materials and through alternation of air flow direction through the combustor. Temperature field, CO and NOx emission with respect to the frequency of alternation are measured. It is found that at initial stage of the alternation, temperature of inlet section of main combustion chamber is increased sharply since both high temperature air preheated by the ceramics and prompt fuel injection results in rapid combustion. Following this initial stage, combustion temperature is reduced as the preheated air temperature is reduced. However peak temperature in the chamber and exhaust gas temperature are decreased as the alternation period is reduced, increased temperature of ceramic is observed. CO and NOx emission with respect to the alternation period is also examined. It is found that there exists a range of optimum alternating period for CO and NOx emission characteristics.

• 농업과학연구
• /
• 제37권3호
• /
• pp.501-508
• /
• 2010

A swirl chamber type diesel engine attachable to 18 kW agricultural tractors was improved to reduce exhaust emissions. Compression ratio and throat area ratio of the combustion chamber were varied to determine optimum combustion conditions. Tests were composed of full load and 8-mode emission tests. Compression ratio was fixed as 21, but the swirl chamber volume was increased by 3.8%. Output power, torque, specific fuel consumption, exhaust gas temperature, and smoke level were not considerably different for compression ratios of 21.5 (reference condition) and 21 (test condition), while NOx, HC, CO and PM levels for the compression ratio of 21 were decreased by 11%, 46%, 28%, 11%, respectively, from those for the compression ratio of 21.5. The tests were also conducted with a compression ratio of 22 and 4.3% increased chamber volume. Output power, torque, exhaust gas temperature and smoke level were greater, while specific fuel consumption was less for the compression ratio of 22 than those for the compression ratio of 21.5. Increase of compression ratio decreased HC and CO levels by 24%, 39%, but increased NOx and PM levels by 24%, 39%. Based on these results, a compression ratio of 21 was selected as an optimum value. Then, full load tests with the selected compression ratio of 21 were carried out for different throat ratios of 1.0%, 1.1%, 1.2%. Output power and torque were greatest and smoke was lowest when throat area ratio was 1.1%, which satisfied the target values of specific fuel consumption (less than 272 g/$kW{\cdot}h$) and exhaust gas temperature (less than $550^{\circ}C$). Therefore, a throat area ratio of 1.1% was selected as an optimum value.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.365-370
• /
• 2000

This study represents effect to attain to the exhaust gas and the exhaust noise by the inner shapes of automobile muffler, and obtained optimization-data for the inner muffler shapes by the temperature variation of the exhaust gas in muffler. The results of noise show to decrease in order of model-1, 2 and 3 under that the engine speed is 3500 R.P.M and similar values beyond it. CO represented good the model-2 at low engine speed and model-1 at high engine speed. The model-3 was show to tiny variation difference by the variables. HC decrease mostly by increase of the engine speed and expressed low values the model-2 at 3,000 R.P.M and the model-1 at high speed. Wholly, the model-2 expressed stable results. The temperature distributions expressed high distributions by increase of the engine speed, and the model-3 was express most good among three models.

• 한국화재소방학회논문지
• /
• 제31권4호
• /
• pp.1-6
• /
• 2017

국내 건축물에 사용되는 내화도료는 품질시험을 통하여 내화구조로 인정받아야 사용할 수 있다. 품질시험은 내화시험 및 부가시험이며 내화도료의 부가시험 항목은 가스유해성과 부착강도이다. 이중 가스유해성의 경우 관련 KS 등에 따라 동물실험을 하며 매건 16마리의 살아있는 쥐가 희생된다. 이에 실험자는 윤리적 부담을 느끼게 되며 실험기관은 관련 법률에 따른 실험동물운영위원회 운영 등 행정적 부담을 지게 된다. 이에 연소 가스의 성분 분석을 통한 유해성 측정 등 상기 동물실험을 대체하려는 연구와 노력이 지속되고 있으나 현재까지는 동물실험이 유지되고 있다. 연소가스의 유해성 평가 시 시험체 가열에 따라 발생하는 배기온도가 측정되는데 특정 타입 내화도료에 대한 배기온도를 분석하여 유의한 초기 반응 양상을 파악할 수 있다면 동물실험 대체에 기여할 수 있을 것이라 사료된다. 이에 본 논문을 통하여 가스유해성 시험 시 쥐의 행동정지시간과 배기온도와의 관계를 파악하여 현 동물실험의 개선점을 찾아보고자 하였다.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.18-28
• /
• 1994

An exhaust-heated gas turbine cycle equipped with a waste heat recovery boiler and ammonia absorption-type refrigerator using waste heat is newly devised and analyzed. The general performance of this cycle is compared with that of the conventional gas turbine cycle. This cycle shows a potential high efficiency. When 1500K of gas turbine inlet temperature the efficiency is 53 percent as compared to 45 percent for a conventional combined cycle. Suction cooling of this cycle leads to improve the thermal efficiency and the specific output.