• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.166-173
• /
• 2006

This study investigates a heavy duty diesel engine with swept vol. 12.6L, 4cycle-OHC type to verify the effects of the performance and exhaust gas emission according to the variable specifications of both swirl ratio and flow coefficient in inlet port, combustion bowl and fuel injection system. To meet the high BMEP and stringent exhaust emission standard, a turbocharger with wastegate and an intercooler were installed in the engine. Helical port, major design parameters for combustion chamber and electronic fuel injection pump with 1,000bar were reviewed and applied. Confirmation tests were also performed to meet the target value, $NO_x$ 5.0g/kWh and PM 0.1g/kWh of Euro3 exhaust emission legislation. The results of this study show that not only is it effective to use a relatively bigger bowl size for controlling rapid burning condition due to the decreased in-bowl swirl, but also to use a concave cam with double injection rates to decrease $NO_x$.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권3호
• /
• pp.180-184
• /
• 2016

국제기구 및 각국의 정부는 인간의 건강 및 환경을 보호하기 위해 선박의 배기가스 규제를 엄격히 적용하고 있다. 함정은 이러한 배기가스 규제 적용 대상에서 제외되고 있지만 최근 미국, 영국 등 일부 선진국에서는 함정으로 야기되는 대기환경오염을 방지하기 위해 전기추진체계 시스템을 도입하는 등 다양한 개선 방법을 적용하고 있다. 본 연구에서는 함정용 디젤엔진의 매연 발생 문제 해결을 위해 노즐 직경을 축소 변화시키고 분사압력을 증가시켜 배기가스 발생량 측정과 오염물질조사 방법론을 이용해 저부하시 매연 문제가 개선된 것을 확인하였다. 동시에 그 영향을 유량방정식과 함정시험평가서를 통해 노즐 직경 축소 결과 연료 소비량이 감소되는 것을 확인하였다.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.159-164
• /
• 2007

The purpose of this study is to reduce harmful emission gases in the range of stable combustion without loss of a thermal efficiency. Therefore, effects of both exhaust gas recirculation(EGR) and synthetic gas addition on engine performance and emission were investigated in a gasoline engine. Synthetic gas(syngas), which is in general prepared from reforming gasoline, was utilized in order to promote stable combustion. The major components of syngas are H2, CO and $N_2$ gases. The percentage of syngas addition was changed from 0 to 30% in energy fraction and EGR rate was varied up to 30%. As a result, $COV_{IMEP}$ as a parameter of combustion stability was decreased and THC/$NO_X$ emissions were reduced with the increase of syngas addition. And $COV_{IMEP}$ was increased with the increase of EGR but $NO_X$ emission was greatly reduced. In addition, under the region where the EGR rate is around 20%, thermal efficiency was improved.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.64-70
• /
• 2007

Raising exhaust gas temperature during cold-start period is very crucial to improve emission performance of SI engines because it enhances the performance of catalyst in the early stage of engine start. In this study, control variables such as ignition timing, idle speed actuator(ISA) opening and fuel injection duration were extensively investigated to analyze variations in exhaust gas temperature and engine stability during cranking period. Experimental results showed that spark timing affected engine stability and exhaust gas temperature but the effects were small. On the other hand, shortened injection duration and increased ISA opening led to a significant increase in exhaust gas temperature. Under such conditions, increase in cranking time was also observed, showing that it becomes harder to start the engine. Based on these observations, a pseudo fuel-air ratio, defined as a ratio of fuel injection time to degree of ISA opening, was introduced to analyze the experimental results. In general, decrease in pseudo fuel-air ratio raised exhaust gas temperature with the cost of stable and fast cranking. On the contrary, an optimal range of the pseudo fuel-air ratio was found to be between 0.3 to 0.5 where higher exhaust gas temperatures can be obtained without sacrificing the engine stability.

• 동력기계공학회지
• /
• 제19권6호
• /
• pp.47-53
• /
• 2015

Korea is the geographic location during the summer, the temperature rising to $35^{\circ}C$ and winter temperature is $-15^{\circ}C$ to reduce the air temperature changes, such as relatively large compared to other countries. This increase or decrease of the harmful exhaust gas discharged from automobile substantially inconvenience a significant impact on the active side of the car engine temperature and exhaust gas reducing device receives a large impact on the atmospheric temperature is regulation to be different. However, domestic vehicle emissions test temperature of $20{\sim}30^{\circ}C$ is it does not reflect this situation the actual test temperature to accurately measure the exhaust gas volume of the vehicle is difficult. In this study, domestic automobile exhaust gas test conditions of a test temperature $20{\sim}30^{\circ}C$ various temperatures, including (35, 25, 0, -7, -15, $-25^{\circ}C$) under the two vehicles (2.0L MPI, 2.4 L GDI) as was discussed with respect to the exhaust gas characteristics of the vehicle according to the ambient temperature gas. As a result, domestic emissions test temperature of $25^{\circ}C$ than average conditions were temperature decreases greenhouse gas emissions and increase overall increased by up to 15 times higher. Air temperature and the engine exhaust gas inconvenience a direct effect on the activation temperature required in the reduction unit is determined to be an increase of emissions and greenhouse gases, and also an increase in the variety of lubricants based lubricating and viscosity reduction, such as the engine oil due to the low temperature of these result It is considered that shows the.

• 한국가스학회지
• /
• 제18권6호
• /
• pp.7-13
• /
• 2014

국내 외에서 대기 오염에 대한 관심은 높은 편이며, 자동차 및 연료 연구자들은 깨끗한 (친환경 대체연료) 연료와 연료 품질에 맞춘 새로운 엔진 설계의 구성, 혁신적인 후처리 시스템 등의 접근을 통하여 차량의 배기가스 배출을 줄이려고 노력하고 있다. 이러한 연구는 다음과 같은 다양한 주요 이슈를 가져오게 된다. PM 배출량이 디젤과 가솔린 차량에 대해 규제해야 하는지 여부와 가솔린 및 LPG 차량이 PM 배출가스 규제에서 무시될 수 있는지 여부이다. 마지막으로 온실 가스 (C$CO_2$, $CH_4$, $N_2O$) 규제가 자동차 배출 규제를 포함하여 논의 것 등이다. 자동차의 온실 가스 및 배출가스(PM)는 환경오염, 건강 악영향 등의 원인으로 많은 문제점을 일으키게 된다. 본 논문에서는 자동차 저온 시동성 및 배출가스에 대해 LPG 연료의 영향을 논의하였다. 또한 본 논문은 시험 온도에 대한 배출가스 특성을 평가하였다. 이때의 시험온도는 시험모드 상의 온도와 국내 겨울철 최저온도를 기준으로 나누어서 실시하였다. 본 연구를 통해 시동성 및 배출가스, 온실가스 배출의 상관관계를 분석하고자 하였다.

• 동력기계공학회지
• /
• 제18권4호
• /
• pp.52-59
• /
• 2014

The purpose of this study is to evaluate the performance of after-treatment equipment and thermal storage devices for a heat recovery and combustor-type $CO_2$ generator fuelled a kerosene. To reduce the levels of harmful exhaust gases produced by a $CO_2$ generator, a catalyzed particulate filter(CPF) has been selected as an after-treatment device, by considering back pressure and exhaust gas temperature. The CO conversions of the catalyzed SiC filter(full plugging) were 92%, and the concentration of PM(particulate matter) was near ambient. A thermal recovery device was used to recover 13% of the heat energy from the exhaust gas through heat exchangers installed on the exhaust line of the $CO_2$ generator. 69% of the moisture within the exhaust gases was removed by condensing water, in order to minimize excessive humidity within the greenhouse.

• 도시과학
• /
• 제11권2호
• /
• pp.45-54
• /
• 2022

Recently, regulations on automobile exhaust gas emission are being strengthened. Accordingly, automobile exhaust gas emissions are expected to decrease and continue to decrease. On the other hand, many countries do not yet consider the emission of non-exhaust air pollutants from automobiles as important. Automobile non-exhaust substances are classified into three categories: tire dust emissions, brake wear emissions, and road scattering dust. In particular, in the case of tire dust, research results exist that pollutant emissions increase as the weight of a vehicle increases. Since the weight of trucks varies according to the load and the load along the axles is also different, it can be expected that the emission of PM10 from the tire dust will be different depending on the loading method. Therefore, this study was conducted on the amount of PM10 generated in tire dust considering the axle load of the truck according to the loading method. However, it was confirmed that the total amount of PM10 was less than that all loads are loaded in the front or rear when the load was evenly distributed in the front and rear of the cargo compartment. In particular, if the load is distributed evenly in the front and back of the cargo compartment and the load in the front part is divided into 2 to 6 and loaded, as the number of divided loading increases the amount of PM10 generated decreases. And when the load is divided into 6 pieces, the total amount of PM10 generated is 0.3952g, the minimum value. If the load is divided into 6 or more and loaded evenly, the total PM10 generated continuously increases and converges to about 0.3964g.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.84-89
• /
• 2014

Not only the emission regulation of on-road vehicle engine, but also emission regulation of off-road engine have been reinforced. It is the reason of wide application of emission reduction technology for off-road engines. In this study, optimization of engine parameters (Injector hole number, Injection timing and EGR rate) for reduction of NOx and smoke emissions were conducted by using the analysis of sensitivity and S/N ratio of Taguchi method(DOE). As results, this paper shows optimum value of the parameters for NOx and smoke emission reduction. From the result of reproducibility verification, it is final that the prediction value of NOx and smoke has the error of below 10%. Consequently, the method and results of this study will be used for quantitative reference to EGR control mapping in next study.

• 한국기계가공학회지
• /
• 제18권8호
• /
• pp.74-81
• /
• 2019

Cars are inspected in the transport sector for their ability to achieve the greenhouse gas reduction targets. A vehicle (automobile) inspection broadly consists of regular and total checks, and both the safety level and the amount of exhaust gas are checked simultaneously during a vehicle inspection. This study deals with the efficiency of a soot probe to measure soot emissions from diesel vehicles. When the vehicle exhaust gas measurement is performed, there may be a difference between the exhaust gas temperature and the soot suction amount because of the different shape and angle of the exhaust port for each vehicle type. This may result in some incidents where the correct inspection nonconforming vehicle is not selected. Therefore, in this study, the shape of the probe was improved to increase the soot measurement efficiency under the condition of the exhaust pipe angle change.