• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2003년도 춘계 학술발표회논문집
• /
• pp.473-480
• /
• 2003

A new semiactive control strategy for seismic response reduction using a neuro-controller and a magnetorheological (MR) fluid damper is proposed. The proposed control system adopts a clipped algorithm which induces the MR damper to generate approximately the desired force. The improved neuro-controller, which was developed by employing the training algorithm based on a cost function and the sensitivity evaluation algorithm replacing an emulator neural network, produces the desired active control force, and then by using the clipped algorithm the appropriate command voltage is selected in order to cause the MR damper to generate the desired control force. The simulation results show that the proposed semiactive neuro-control algorithm is quite effective to reduce seismic responses. In addition, the semiactive control system using MR fluid dampers has many attractive features, such as bounded-input, bounded-output stability and small energy requirements. The results of this investigation, therefore, indicate that the proposed semiactive neuro-control strategy using MR fluid dampers could be effective used for control seismically excited structures.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.531-536
• /
• 2006

In four cylinder engine, the second order inertia force occurs due to the reciprocating parts of the cylinder. Because the magnitude of the inertia force is proportional to a square of the angular velocity of crank shaft, engine gets suffered from vibration excited by unbalanced inertia force in high speed. This vibration excited by the unbalanced inertia force can be canceled by applying a balance shaft. Balance shaft has one or more unbalance mass and rotates twice quickly than the crank shaft. In this paper, an unbalanced force caused by the rotating of unbalance mass of balance shafts was calculated. The directional equivalent stiffness and damping coefficients of the journal bearing of balance shafts was calculated. Equations of rotational vibration modes were derived using directional stiffness and damping coefficients. The dynamic stability of balance shafts was analyzed and evaluated for two type models using the equivalent stiffness and damping coefficients. An efficient procedure to he able to evaluate dynamic stability and design optimal balance shaft was proposed.

• 한국소음진동공학회논문집
• /
• 제11권6호
• /
• pp.181-192
• /
• 2001

The power flow analysis (PFA) has been performed to analyze the vibration of coupled plates excited by a point force in an arbitrary direction. The point force generates the out-of-plane vibration associated wish flexural waves and the in-plane vibration associated with longitudinal and shear waves. The energy governing equation for each type of waves was introduced and solved to Predict the vibrational energy density and intensity generated by the out-of-plane and in-plane components of the point force in an arbitrary direction. The wave transmission approach was used to consider the mode conversion at the joint of the coupled plates. Numerical results for vibrational energy density and intensity on the coupled plates were presented. Comparison of the results by PFA with exact results showed that PFA can be an effective tool to predict the spatial variation of the vibrational energy and intensity on the coupled plates at high frequencies.

• 한국지진공학회논문집
• /
• 제8권2호
• /
• pp.1-8
• /
• 2004

제어효과가 탁월한 능동제어알고리듬의 하나인 슬라이딩 모드제어(SMC)는 지진력을 받는 구조물의 제어를 위해 매우 큰 크기의 제어력을 요구한다. 따라서, SMC의 설계에 있어 제어기의 포화문제는 반드시 고려되어야 한다. 본 논문은 설계응답스펙트럼에 따른 구조율의 복원력을 이용하여 제어기의 최대 제어력을 결정하는 방법을 제안한다. 한 개 혹은 다수의 제어장치를 설치한 다층건물의 수치해석 결과는 제안된 방법이 지진하중을 받는 구조물의 포화 슬라이딩모드제어에 유효함을 보며준다.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.122-128
• /
• 1996

In high speed and high precision assembly systems such as a surface mounting device and robotend effector, the contact force control is required. As the operation repeats, the repetitive control is applied to reduce the periodic contact force errors. Since high order unmodelled dynamics are easily excited in contact force control, a Q filter was introduced and its robust stability was analyzed. Simulation and Experimental results show the effectiveness of the algorithm.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권1호
• /
• pp.16-23
• /
• 2004

Permanent magnet-excited transverse flux linear motor(TFLM) is known to have more excellent ratio of force to weight than any other linear motors. But, thrust generated by phase current is non-linear with regard to current and relative position like switched reluctance motor. This makes current and speed controller design difficult. This paper presents a method on minimization of thrust ripple of permanent magnet-excited transverse flux linear motor. Using genetic algorithm(GA), optimal current waveform can be found under the constraint conditions such as current limit, minimum of ohmic loss and limited rate of change of current etc. The effectiveness is verified through computer simulation and experimental test results.

• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.281-288
• /
• 2002

본 논문은 영구자석 여자 횡축형 선형 전동기(TFLM)를 이용한 가진기 제어 시스템을 구현하고자 한다. 제안된 가진기는 대상 물체에 정격 전류에서 최대 700[N]의 가진력과 넓은 변위 및 주파수 운전 범위를 갖는 진동운동을 제공한다. 또한 가진기에 적용된 TFLM은 구조적으로 높은 추력비(전동기 추력/전동기 중량=N/Kg)를 가지므로 전체 시스템의 부피가 감소된다. 따라서 기존의 유압식 가진기를 제안한 가진기로 대체할 경우 효율 및 유지, 관리면에서 많은 장점이 있다. 가진 제어를 위한 제어기의 입력은 가진 주파수와 변위이며 제어량은 이동자의 순시 위치와 속도이고 출력은 가진기에 인가되는 전류이다. 이 전류는 전압형 PWM 컨버터로 제어된다 우선 가진기 제어시스템의 제어 알고리즘과 운전 특성을 고찰하고 해석하기 위해 동적 시뮬레이션을 수행한 후 DSP 제어기와 IGBT PWM 컨버터를 구현하여 실제 실험 결과와 비친, 검토하였다.

• International Journal of Fluid Machinery and Systems
• /
• 제3권1호
• /
• pp.67-79
• /
• 2010

Severe flexural vibration of the rotor shaft of a Francis turbine runner was experienced in the past. It was shown that the vibration was caused by the fluid forces and moments on the backshroud of the runner associated with the leakage flow through the back chamber. The aim of the present paper is to study the self-excited rotor vibration caused by the fluid force moments on the backshroud of a Francis turbine runner. The rotor vibration includes two fundamental motions, one is a whirling motion which only has a linear displacement and the other is a precession motion which only has an angular displacement. Accordingly, two types of fluid force moment are exerted on the rotor, the moment due to whirl and the moment due to precession. The main focus of the present paper is to clarify the contribution of each moment to the self-excited vibration of an overhung rotor. The runner was modeled by a disk and the whirl and the precession moments on the backshroud of the runner caused by the leakage flow were evaluated from the results of model tests conducted before. A lumped parameter model of a cantilevered rotor was used for the vibration analysis. By examining the frequency, the damping rate, the amplitude ratio of lateral and angular displacements for the cases with longer and shorter overhung rotor, it was found that the precession moment is more important for smaller overhung rotors and the whirl moment is more important for larger overhung rotors, although both types of moment due to the leakage flow can cause self-excited vibration of an overhung rotor.

• Journal of Power Electronics
• /
• 제15권2호
• /
• pp.419-430
• /
• 2015

Flux estimation is a significant foundation of high-performance control for DC-excited synchronous motor. For almost all flux estimators, such as the flux estimator based on phase locked loop (PLL), DC drift causes fluctuations in flux magnitude. Furthermore, significant dynamic error may be introduced at transient conditions. To overcome these problems, this paper proposes an improved flux estimator for the PLL-based algorithm. Filters based on the generalized integrator are used to avoid flux fluctuation problems caused by the DC drift at the back electromotive force. Programmable low-pass filters are employed to improve the dynamic performance of the flux estimator, and the cutoff frequency of the filter is determined by the dynamic factor. The algorithm is verified by a 960V/1.6MW industrial prototype. Simulation and experimental results show that the proposed estimator can estimate the flux more accurately than the PLL-based algorithm in a cycloconverter-fed DC-excited synchronous machine vector control system.

• International Journal of Fluid Machinery and Systems
• /
• 제6권4호
• /
• pp.206-212
• /
• 2013

Self-excited pulse jet is a specific nozzle with a closed chamber which can change a continuous jet into a pulse one. Energy of the pulse jet can be output not only unevenly but also with multifrequency. With the peak pressure of pulse jet, the hitting power would be 2~2.5 times higher than that of continuous jet. In order to reveal the correlation between the self-excited pulse frequency and nozzle diameter ratio, nozzle spacing and operating pressure, the model of 3D unsteady cavitation model has been used. We found that with the same nozzle structure parameters and the different operating pressure, the self-excited frequency and the width of peak crest are different, but the wave profiles are similar. With FFT, we also found that the less bandwidth of amplitude in low frequency range will lead to the wider wave crest of outlet velocity in its time domain, and the larger force of the strike will be gained. By studying the St of self-excite nozzle, not only the frequency of a certain nozzle can be predicted, but also a nozzle structure with a certain frequency can be designed.