• Resources Recycling
• /
• v.31 no.6
• /
• pp.60-65
• /
• 2022

This study presents the carburization process for recycling sludge, which was formed during silicon wafer machining. The sludge used in the carburization process is a mixture of silicon and silicon carbide (SiC) with iron as an impurity, which originates from the machine. Additionally, the sludge contains cutting oil, a fluid with high viscosity. Therefore, the sludge was dried before carburization to remove organic matter. The dried sludge was washed by acid cleaning to remove the iron impurity and subsequently carburized by heat treatment under vacuum to form the SiC powder. The ratio of silicon to SiC in the sludge was varied depending on the sources and thus carbon content was adjusted by the ratio. With increasing SiC content, the carbon content required for SiC formation increased. It was demonstrated that substoichiometric SiC_x (x<1) was easily formed when the carbon content was insufficient. Therefore, excess carbon is required to obtain a pure SiC phase. Moreover, size reduction by high-energy milling had a beneficial effect on the suppression of SiC_x, forming the pure SiC phase.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.12 no.1
• /
• pp.7-11
• /
• 1983

The purpose of this study was to prepare low methoxyl pectins (LMPs) by pectinesterase (PE) using waste tangerine peels and to compare the chemical, physical and gelling properties of the prepared pectins with the commercial LMP. The LMPs were prepared by treating albedo with 0.25M $Na_2CO_3$ to activate the PE. PE was then inactivated by heating. The sample was centrifuged and the supernatant was collected. LMP was obtained as precipitate by adding alcohol to the collected supernatant. The amounts of extractible pectins in albedo were 12.71~12.98% on a dry weight basis. Methoxyl contents of LMPs prepared by treating albedo with PE at pH 7.5 for 10min, at pH 8.5 for 10min, 20min and 30min were 5.12%, 4.27%, 3.08%, 1.85% respectively, demonstrating that the methoxyl contents of the preparations decreased as the degree of treatment albedo with PE increased. The acetyl contents of the preparations ranged from 0.09% to 0.12%, the values of which do not interfere with gel formation. The anhydrouronic acid contents of the prepared pectins were in the range of 94.2%~94.8%. The values of viscosity and molecular weights of the prepared LMPs tent to decrease as the degree of PE action on albedo increased. The textural value of the prepared LMP gels determined by Consistometer, Ridgelimeter and Instron denonstrated that the excess treatment of albedo with PE significantly impaired the gelling properties of the preparations.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.438-442
• /
• 2005

Granule swelling is essential phenomenon of starch gelatinization in excess water, and characteristic of heated starch dispersion depends largely on size and distribution of swelled starch granule. Although swelling characteristic of starch granules depends on type of starch, heating rate, and moisture content, influence of heating rate on swelling phenomenon of starch granule has not been fully discussed, because constant heating rate of starch dispersion cannot be obtained by conventional heating method. Ohmic heating, electric-resistant heat generation method, applies alternative current to food materials, through which heating rate can be easily controlled precisely and conveniently at wide range of constant heating rates. Starch dispersion heated at low heating rates below $7.5^{\circ}C/min$ showed Newtonian fluid behavior, whereas showed pseudoplastic behavior at heating rates above $16.4^{\circ}C/min$. Apparent viscosity of starch dispersion increased linearly with increasing heating rate, and yield stress was dramatically increased at heating rates above $16.4^{\circ}C/min$. Average diameter of corn starch granules during ohmic heating was dramatically increased from $30.97\;to\;37.88\;{\mu}m$ by increasing heating rate from $0.6\;to\;16.4^{\circ}C/min$ (raw corn starch: $13.7\;{\mu}m$). Hardness of starch gel prepared with 15% corn starch dispersion after heating to $90^{\circ}C$ at different heating rates decreased gradually with increasing heating rate, then showed nearly constant value from $9.4\;to\;23.2^{\circ}C/min$. Hardness increased with increase of heating rate higher than $23.2^{\circ}C/min$.