• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.673-676
• /
• 2003

We have investigated $Al_{x}$ $Ga_{l-x}$ N/GaN epilayers (x = 0.08, 0.15) grown by metal organic vapor phase epitaxy on sapphire with photoluminescence(PL), and persistent photoconductivity(PPC) experiments. An anomalous S-shaped shift behavior of temperature dependencies of PL peak energy is observed for the x = 0.15 sample. In PPC measurement, showed that the dark current recovery time of $Al_{x}$$Ga_{l-x}$ N/GaN epilayers mainly depends on the Al content. These behaviors are usually attributed to the presence of carrier localization states. All these phenomena are explained based on the alloy compositional fluctuations in the $Al_{x}$ /$Ga_{l-x}$ N/ epilayers. The photocurrent quenching observed in PPC measurements for $Al_{x}$ $Ga_{l-x}$ N/ epilayers less than 0.2 $\mu\textrm{m}$ thickness indicates that the presence of metastable state in the bandgap of GaN layer, and that the excess holes in the valence band recombine with free electrons.

• Journal of Power System Engineering
• /
• v.12 no.4
• /
• pp.5-11
• /
• 2008

The RI gasoline engine haying a sub-chamber had a high cycle variation due to the difficulty of the residual gas scavenge in the sub-chamber. To solve this problem and improve the combustion performance of RI engine, we devised a method to inject directly CNG fuel into the sub-chamber. A DI diesel engine of single cylinder was converted into a RI-CNG engine and an electronic control unit for the engine was manufactured. In this study, the combustion characteristics of the RI-CNG engine were investigated with the injection timings and air excess ratios at the load conditions of 50% throttle open rate and 1700rpm. As the results from this study, the RI-CNG engine worked reliably under the condition of the ignitable lean limit of $\lambda=1.7$ by showing the $COV_{imep}$ below about 5%. And the highest thermal efficiency could be obtained in the injection timing that produced the high imep and the low $COV_{imep}$ at the same time. The CO emission concentration indicated very low values and the THC and $NO_x$ showed an opposite pattern. With a view to improving the thermal efficiency and reducing the harmful emissions, the proper control region of the ignition timing and the mixture ratio were nearly ATDC $20^{\circ}\sim50^{\circ}$ and $\lambda=1.4$ respectively.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.4
• /
• pp.719-741
• /
• 1997

This study was undertaken to compare by Atomic Force Microscope the effects of various finishing and polishing instruments on surface roughness of filling and veneering composite resins. Seven composite resins were studied : Silux Plus (3M Dental Products, U.S.A.), Charisma (Heraeus Kulzer, Germany), Prisma THP (L.D.Caulk, Dentsply, U.S.A.), Photoclearfil (Kuraray, Japan), Cesead (Kuraray, Japan), Thermoresin LC (GC, Japan), Artglass (Heraeus Kulzer, Germany). Samples were placed and polymerized in holes (2mm thick and 8.5mm in diameter) machined in Teflon mold under glass plate, ensuring excess of material and moulded to shape with polyester matrix strip. Except control group (Polyester matrix strip), all experimental groups were finished and polishied under manufacturer's instructions. The finishing and polishing procedure were : carbide bur (E.T carbide set 4159, Komet, Germany), diamond bur (composite resin polishing bur set, GC, Japan), aluminum-oxide disc (Sof-Lex Pop-On, 3M Dental Products, U.S.A.), diamond-particle disc (Dia-Finish, Renfert Germany), white stone bur & rubber point( composite finishing kit, EDENTA, Swiss), respectively. Each specimens were evaluated for the surface roughness with Atomic Force Microscope (AutoProbe CP, Park Scientific Instruments, U.S.A.) under contact mode and constant height mode. The results as follows : 1. Except Thermoresin LC, all experimental composite resin groups showed more rougher than control group after finishing and polishing(p<0.1). 2. A surface as smooth as control group was obtained by $Al_{2}O_{3}$ disc all filling composite resin groups except Charisma and all veneering composite resin groups except Thermoresin LC(p<0.05). 3. In case of Thermoresin LC, there were no statistically significant differences before and after finishing and polishing(p>0.1). 4. Carbide bur, diamond bur showed rough surfaces in all composite resin groups, so these were inappropriate for the final polishing instruments.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.4
• /
• pp.187-192
• /
• 2011

Photoelectrochemical performances of ZnO electrodes are enhanced by coupling with cobalt-based catalyst (CoPi) in phosphate electrolyte (pH 7). For this study, hexagonal pillar-shaped ZnO nanorods are grown on ZnO electrodes through a chemical bath deposition, onto which CoPi is deposited with different photodeposition times (10-30 min). A scanning electron microscopic study indicates that CoPi deposition does not induce any change of ZnO morphology and an energy-dispersive X-ray spectroscopic analysis shows that inorganic phosphate ions (Pi) exist on ZnO surface. Bare ZnO electrodes generate the current of ca. $0.36mA/cm^2$ at a bias potential of 0.5 V vs. SCE, whereas ZnO/CoPi (deposited for 10 min) has ca. 50%-enhanced current ($0.54mW/cm^2$) under irradiation of AM 1.5G-light ($400mW/cm^2$). The excess loading of CoPi on ZnO results in decrease of photocurrents as compared to bare ZnO likely due to limited electrolyte access to ZnO and/or CoPi-mediated recombination of photogenerated charge carriers. The primary role of CoPi is speculated to trap the photogenerated holes and thereby oxidize water into molecular oxygen via an intervalency cycle among Co(II), Co(III), and Co(IV).

• Design & Manufacturing
• /
• v.15 no.2
• /
• pp.30-35
• /
• 2021

The casting method uses a mold to solidify a liquid metal to make a solid metal. Since it uses a liquid metal with the least deformation resistance, it has the characteristic that it can easily manufacture even a complex shape. However, the process of solidifying a liquid metal into a solid metal inevitably involves a volume change and contains internal defects such as shrinkage holes. Therefore, in the design of the casting plan, an excess volume called a pressurization compensates for the volume shrinkage. in the product, and it induces the shrinkage hole defects to occur in parts other than the product1). In this study, casting analysis was performed using casting analysis software (anycasting) in order to optimize the design of the tilting gravity casting method for automobile brackets. In particular, the filling and solidification analysis according to the shape and volume of the pressurized metal was conducted, and applied to the actual product to study the effect of the pressurized metal on the shrinkage defect. Through this study, it is possible to understand the effect of the pressure metal on shrinkage defects in the actual product and propose a design of the pressure metal that improves reliability and productivity.

• Nuclear Engineering and Technology
• /
• v.13 no.4
• /
• pp.264-276
• /
• 1981

A simulation procedure which can represent time-dependent nuclear characteristics of TRIGA Mark-III reactor is developed. CITATION, a multi-group diffusion-depletion program, has been utilized as calculational tool. The group structure employed in this study consists of 7 groups: -3-fast and 4-thermal-which is conventionally utilized in TRIGA type reactor analysis. Three-dimensional nuclear characteristics are synthesized by combining results from two-dimensional plane calculation and two-dimensional cylinder calculation, since direct three-dimensional approach is not yet possible. An effort ia made to develope a method which can extract effective zone and group dependent bucklings by neutron diffusion theory rather than conventional zone and/or group independent Ducklings by neutron transport theory, since neutron leakage is quite high for small core such as research reactors. It is turned out that the method developed in this study gives satisfactory results. The calculation is performed under assumptions that all control rods are fully withdrawn, that no samples are inserted in the irradiation holes and that the core is located in the center of the reactor pool. Burnup-dependent variation of core excess reactivity, time dependent change of Xe-135 poisoning and reactivity worth of rotary specimen rack are calculated and compared with operation records. Neutron flux and power distribution as well as neutron spectrum in each irradiation .facility are presented.

• Journal of Acupuncture Research
• /
• v.20 no.1
• /
• pp.131-143
• /
• 2003

Objective : The purpose of this study is to arrange the literature about acupuncture therapy on the hemorrhoids and hemorrhoid complicated by anal fistula. Methods : We arrange Huang Di Nei Jing and fifteen kinds of literature about the hemorrhoids and hemorrhoid complicated by anal fistula. Results : 1. The cause of hemorrhoids are overfatigue, overeating, imbalance of stool(const-ipation or diarrhea), uncontrol sexual excess or abstinence, pathgenic factors of wetness, heat, wind, dry, fire, chronical hemorrhoids that has not been treated, and general weakness. 2. Symptom of hemorrhoids is that skin is projected form the nine holes or varicose extension to become hemorrhoid. Hemorrhoids is small nodosity that projected on the anal inter or outer region, and hemorrhoid complicated by anal fistula is pus which comes out form one or some fistula on the anal around inter and outer region. 3. Therapy method of hemorrhoid and hemorrhoid complicated by anal fistula are elimination pathological heat from blood, promote blood flow to remove blood stasis, cold in nature and purge away fire, remove heat form the blood, promote blood flow to remove blood stasis, cold in nature and purge away fire, remove heat from the blood and eliminate dampness, tonify the spleen and replenish Ki, dispel wind and alleviate pain and so forth. Therapy method of hemorrhoid is to give the first consideration to relieve blood: eliminating pathological heat form blood complicated by anal fistula is to tonify the blood first, than after that eliminating pathological heat form blood. About external method are method of fumigation, method of ointment, method of close with medicine, necrotizing method and also operation(injection, bind etc.)was used for treatment. 4. The prescription are Gurgak-hwan, Wypi-hwan, Gunggyi-tang, Jingyochangchul-tang, Jingyobangpung-tang, Mokhyangbinrang-hwan, Ochi-san, Gamihyanso-san, Jojang-hwan, Sinyung-hwan used frequently. 5. food taboo on patient's diet of the hemorrhoid and hemorrhoid complicated by anal fistula are raw grain, cold or dampness food, alcohol, hot food, Singiberis rhizoma recens, Cinnamomi ramulus. 6. Acupuncture therapy on the hemorrhoid and hemorrhoid complicated by anal fistula are, in the first stage eliminating pathological heat form blood and eliminate dampness, and in the long term eliminate dampness, promote and remove meridian energy, remove that form the intestines, dispel channels and collaterals. 7. Acupuncture points at B2, CV1, B58, B36, B56, Sp5, S30, B25, B54, GV1, GV20, L6, B40 used frequently for the acupuncture therapy, and acupuncture point at GV4, GV1, B30, hemorrhoidal point used form moxibustion. Reduction blood at B40 and blue capillary of Sp9 and acupuncture Chungbaek, Ki-gack, Ki-jung, Ki-mun(Dongsh Kihyel) makes the treatment very effective.

• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.83-90
• /
• 1990

The semiconducting $(Pb_1\;_xSn_x)_1$ $_yTe_y$, one of the low - temperature thermoelectric materials, has been prepared and its chemical composition and nonstoichiometry has been analyzed. The content of Pb in the specimens was determined by the complexometric back - titration method with EDTA and Pb(II) standard solutions. Te - content was analyzed with the redox titration method. The electrical conductivity and the thermoelectric power have also been measured by the DC 4 - probe and the heat-pulse technique, respectively. All of the specimens showed a nonstoichiometric behavior in their chemical compositions (Te excess), thus gave rise to a p - type semiconducting property, and the nonstoichoimetry became bigger as the Sn - content increased. The thermoelectric power vs. temperature results have been analyzed upon the basis of the Fermi level vs. temperature profiles in the saturation regime. The specimen of x=0.1 evolved a transition from p - to n - type property at about 670K, which has been explained by the fact that the mobility of electrons is bigger than that of holes in the temperature range of the intrinsic regime.

• Journal of Biosystems Engineering
• /
• v.5 no.1
• /
• pp.1-14
• /
• 1980

Threshing operation may be one of the most important processes in the paddy post-production system as far as the grain loss and labor requirement are concerned . head-feeding type threshers commercially available now in Korea originally were developed for threshing dry paddy in the range of 15 to 17 % in wet basis. However, threshing wet-paddy with the grain moisture content above 20 % has been strongly recommended, especially for new high-yielding Indica -type varieties ; (1) to reduce high grain loss incurred due to the handling operations, and (2) to prevent the quantitative and qualitative loss of milled -rice when unthreshed grains are rewetted due to the rainfall. The objective of this study were to investigate the adaptability of both a head-feeding type thresher and a throw-in type thresher to wet-paddy , and to find out the possiblilities of improving the components of these threshers threshing. Four varieties, Suweon 264 and Milyang 24 as Tongil sister line varieties, minehikari and Jinhueng as Japonica-type varieties, were used at the different levels of the moisture content of grains. Both the feed rate and the cylinder speed were varied for each material and each machine. The thresher output quality , composition of tailing return, and separating loss were analyzed from the sampels taken at each treatment. A separate experiment for measurement opf the power requirement of the head-feeding type thresher was also performed. The results are summarized as follows : 1. There was a difference in the thresher output quality between rice varieties. In case of wet-paddy threshing at 550 rpm , grains with branchlet and torn heads for the Suweon 264 were 12 % and 7 % of the total output in weight, respectively, and for the Minehikari 4.5 % and 2 % respectively. In case of dry paddy threshing , those for the Suweon 264 were 8 % and 5% , and for the Minehikari 4% and 1% respectively. However, those for the Milyang 23 , which is highly susceptable to shattering, were much lower with 1 % and 0.5% respectively, regardless of the moisture content of the paddy. Therefore, it is desirable to breed rice varieties of the same physical properties as well as to improve a thresher adaptable to all the varieties. Torn heads, which increased with the moisture content of rall the varieties except the Milyang 23 , decreased as the cylinder speed increased, but grains with branchlet didnt decrease. The damaged kernels increased with the cylinder speed. 3. The thresher output quality was not affected much by the feed rate. But grains with branchlet and torn heads increased slightly with the feed rate for the head-feeding type thresher since higher resistance lowered at the cylinder speed. 4. In order to reduce grains with branchlet and torn heads in wet-paddy threshing , it is desirable to improve the head-feeding type thresher by developing a new type of cylinder which to not give excess impact on kernels or a concave which has differenct sizes of holes at different locations along the cylinder. 5. For the head-feeding type thresher, there was a difference in separating loss between the varieties. At the cylinder speed of 600 rpm the separating losses for the Minehikari and the Suweon 264 were 1.2% and 0.6% respectively. The separating loss of the head-feeding type thresher was not affected by the moisture content of paddy while that of the Mini-aged thresher increased with the moisture content. 6. From the analysis of the tailings return , to appeared that the tailings return mechanism didn't function properly because lots of single grains and rubbishes were unnecessarily returned. 7. Adding a vibrating sieve to the head-feeding type thresher could increase the efficiency of separation. Consequently , the tailing return mechanism would function properly since unnecessary return could be educed greatly. 8. The power required for the head-feeding type thresher was not affected by the moisture content of paddy, but the average power increased linearly with the feed rate. The power also increased with the cylinder speed.