• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.268-273
• /
• 2001

A fundamental study on the harvest-type ice storage system applied ice making method in-water and its temperature characteristics in ice storage system was performed experimentally of the charge and discharge of cold. This paper is concerned with the development of a new method for making and separating ice and saving floated ice by installing an evaporation plate at in-water within a storage tank. In a conventional harvest-type ice storage system, a tank saves ice by separating a formed ice from an installed evaporation plate, which is located above an ice storage tank as an ice storage system. A new harvest-type method shows very good heat transfer efficiency than a convectional method. It is because the evaporation panel is directly contacted with water in a storage tank. Also, at a conventional system a circulating pump, a circulating water distributor and a piping are installed, but these components are not necessary in a new method. In this study two kinds of ice storage systems are experimentally investigated to study the thermal characteristics of ice storage tanks.

• Archives of Pharmacal Research
• /
• v.18 no.1
• /
• pp.22-26
• /
• 1995

The solubility and dissolution rate of naproxen (NPX) complexed with 2-hydroxypropyl-.betha.-cyc-lodextrin (2-HP.betha.CD) using coprecipitation, evaporation, freeze-drying and kneading method were investigated. Solubility of NPX linearly increased (correlation cefficient, 0.995) as $2-HP\betaCD$ concentraction increased, resutling in $A_l$ type phase solubility curve. Inclusion complexes prepared by four different methods were compared by different methods were compared by dfferential scanning calorimetry(DSC). The NPX showed sharp endothemic peak around $156^{\circ}C$ but inclusion complexes by evaporation, freeze-drying and kneading method showed very broad peak without distinct phase transtion temperature. In contrast, inclusion complex prepared by coprecipitation method resulted in detectable peak around $156^{\circ}C$ which is similar to NPX, suggesting incoplete formation of indusion co plex. Dissolution rate of inclusion complexes prepared by evaporation, frezz-drying and kneding except coprecipitation method was largely enhanced in the simultaed gastric and intestinal fluid when compared to NPX powder and commercial $NA-XEN^\registered$tablet. However, about 65% of NPX in gstric fluid. in case of inclusion complex prepared by coprecipitation method, formation of inclusion complex appeared to be incoplete, resulting in no marked enhancement of dissolution rate. From these findings, inclusion complexes of poorly water-soluble NPX with $2-HP\betaCD$ were useful to increase soubility and dissolution rate, resting in enhancement of bioavailability and minimization of gastrointestinal toxicity of drug upon oral administration of inclusion complex.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.1
• /
• pp.31-37
• /
• 2002

This paper is concerned with the development of a new method for making and separating ice and saving floated ice by installing an evaporation plate at in-water within a storage tank. In a conventional harvest-type ice storage system, a tank saves ice by separating a formed ice from an installed evaporation plate, which is located above an ice storage tank as an ice storage system. A new harvest-type method shows very good heat transfer efficiency than a convectional method. It is because the evaporation panel is directly contacted with water in a storage tank. Also, at a conventional system a circulating pump, a circulating water distributor and a piping are installed, but these components are not necessary in a new method. In this study two kinds of ice storage systems are experimentally investigated to study the thermal characteristics of ice storage tanks. The results showed discharge of cold capacity of new type indicated the high values about 30~40% based on five time of drive, the temperature difference of inlet/outlet occurred the big range about $1.3^{\circ}C$. So, the new type which makes ice in water showed superiorly.

• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.349-358
• /
• 1995

The ceramic composite membrane was synthesized by thermal oxidation after evaporation of Al on the support prepared by slip casting process. Oxidation was performed at $700^{\circ}C$ and 80$0^{\circ}C$ under dry oxygen atmosphere. It was considered as optimum oxidation condition that the membrane showed a knudsen behaviro. A further oxidation resulted in an increase of gas permeability because top layer became densified. Then, a multi-layered composite membrane was synthesized through a sol-gel method, evaporation and thermal oxidation of Al coating processes. While the membrane was thermally stable up to 80$0^{\circ}C$, gas permeability was rapidly decreased even at a slight amount of deposition of Al.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.74-80
• /
• 2002

In this study, a numerical method for fuel droplet evaporation in cylinder of S.I. engine is presented. This study was newly defined non-dimensional critical droplet lifetime and modeled heating and evaporation processes of fuel droplet during intake and compression stroke of gasoline engine. The simulation results show that simultaneous increase of gas temperature and pressure in compression stroke seems to have compensative effect on droplet gasification rate. The environment variations in cylinder have little effect on the fuel droplet gasification process. The droplet size for full evaporation at the end of compression stroke can be estimated using this program.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.59-64
• /
• 2001

The fluid flow, mass transfer and film thickness variation during a wafer spin coating process are numerically studied. Governing equations for the cylindrical coordinates are simplified using the similarity transformation and solved efficiently using the finite difference method. Concentration dependent viscosity and the binary diffusivity of the coating liquid are used in the analysis. The time variational velocity components of the coating liquid and the film thickness are analyzed according to the various spin speed. When the evaporation is considered, the flow decease in the early times due to the increase of the viscosity and the resultant flow resistance. Effects of the two film thinning mechanism, the flow-out and evaporation are also considered in the analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.591-596
• /
• 2001

The purpose of this paper Is to present and discuss some of evaporation and desiccation observed in laboratory experiments under controlled conditions, and is to improve PTM(Progressive Trenching Method) operating technique. PTM is the technically feasible and economically justifiable dewatering and desiccation technique for dredged material containment areas. A series of laboratory experiments with large model test were carried out to get evaporation rate and strength increase. Surface desiccation of dredged material is basically changed by evaporation characteristics which is controlled by weather and trench type, etc. This study shows that trench depth and rain fall are important factors in desiccation of dredged soft clay.

• Membrane and Water Treatment
• /
• v.4 no.4
• /
• pp.223-236
• /
• 2013

The paper presents an experimental set-up for osmotic membrane distillation, which can be operated continuously for several weeks. NaCl solutions were used as an osmotic solution. The influence of osmotic solution concentration on the obtained permeate flux is presented. The experimental set-up was equipped with a system for the regeneration of dilute brine. The regeneration was carried out using a method of natural evaporation to the air surrounding the installation. The evaporation area was created by the Białecki rings, assembled in the form of tower. The obtained evaporation rate was sufficient to maintain a constant NaCl concentration (over 300 g/L), for air with the relative humidity in the range of 30-80%. Accurel PP S6/2 hydrophobic polypropylene membranes were used in the study. The membranes exhibited 100% rejection for 600 h of the process duration.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.514-522
• /
• 1999

The laser-induced plasma affects greatly on the results of welding process. moreover selective evaporation loss of alloying elements leads to change in chemical composition of weld metal as well as the mechanical properties of welded joint. this study was undertaken to obtain a fundamental knowledge of pulsed laser welding phenomena especially evaporation mechanism of different aluminum alloys. The intensities of molecular spectra of AlO and MgO were different each other depeding on the power density of a laser beam Under the low power density condition the MgO band spectrum was predominant in intensity while the AlO spectra became much stronger with an increase in the power density. These behaviors have been attributed to the difference in evaporation phenomena of Al and Mg metals with different boiling points and latent heats of vaporization. The time-averaged plasma temperature and electron number density were determined by spectroscopic methods and consequently the obtained temperature was $3,280{\pm}150K$ and the electron number density was $1.85{\times}10^{19}\;l/m^3$.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1596-1599
• /
• 2010

Group method of data handling neural networks model (GMDH-NNM) is used to estimate daily pan evaporation (PE) using limited climatic variables such as max temperature ($T_{max}$), min temperature ($T_{min}$), mean wind speed ($W_{mean}$), mean relative humidity ($RH_{mean}$) and sunshine duration (SD). And, for the performances of GMDH-NNM, it is composed of training and test performances, respectively. The training and test performances are carried out using daily time series data, respectively. From this research, we evaluate the impact of GMDH-NNM for the modeling of the nonlinear time series data. We should, thus, construct the credible data of the daily PE data using GMDH-NNM, and can suggest the methodology for the irrigation and drainage networks system. Furthermore, this research represents that the strong nonlinear relationship such as pan evaporation modeling can be generalized using GMDH-NNM.