• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.7
• /
• pp.462-469
• /
• 2008

A regenerative evaporative cooler has been fabricated and tested for the evaluation of cooling performance. The regenerative evaporative cooler is a kind of indirect evaporative cooler comprised of multiple pairs of dry and wet channels. The air flowing through the dry channels is cooled without any change in the humidity and at the outlet of the dry channel a part of air is redirected to the wet channel where the evaporative cooling takes place. The regenerative evaporative cooler fabricated in this study consists of the multiple pairs of finned channels in counterflow arrangement. The fins and heat transfer plates were made of aluminum and brazed for good thermal connection. Thin porous layer coating was applied to the internal surface of the wet channel to improve surface wettability. The regenerative evaporative cooler was placed in a climate chamber and tested at various operation condition. The cooling performance is found greatly influenced by the evaporation water flow rate. To improve the cooling performance, the evaporation water flow rate needs to be minimized as far as the even distribution of the evaporation water is secured. At the inlet condition of $32^{\circ}C$ and 50%RH, the outlet temperature was measured at $22^{\circ}C$ which is well below the inlet wet-bulb temperature of $23.7^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.23 no.4
• /
• pp.437-441
• /
• 1991

During the evaporation of garlic juice by centrifugal thin film evaporator (Centri-Therm, CT-1B), the effect of feeding rate was investigated for its operation properties. On the process condition of feeding rate of 25 to 125 kg/h, theoretical average thickness of the garlic juice film on the rotating cone and residence time of the juice in the evaporator varied in the range of 0.52 to 0.89 mm and 1.77 to 6.75 second, respectively. And the flow of garlic juice was considered as a streamline flow by Reynolds number. At constant temperatures of steam and juice evaporation, concentration ratio decreased with the increase of the feeding rate. But the evapoartion rate and overall heat transfer coefficient increased with the increase of the feeding rate until the feeding rate reached a certain value and then decreased. On the conditions of $25{\leq}$feeding rate ${\leq}125\;kg/h$, evaporation temperature of $40^{\circ}C$, $95{\leq}steam$ $temperature≤120^{\circ}C$ and initial feed concentration of $32^{\circ}Brix$, concentration ratio and overall heat transfer coefficient were $1.04{\sim}2.04\;and\;3,074.33{\sim}17,614.70kJ/m^{2}{\cdot}h{\cdot}^{\circ}C$.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.1
• /
• pp.72-79
• /
• 1998

Journal of the Korean Society of Clothing and Textiles Vol. 22, No. 1 (1998) p. 72∼79 The purpose of this study was to investigate the effects of geometrical structure and fiber type on the water vapor transport properties of nonwoven batting materials. Two types of fiber were used such as polyester and wool. Correlation between physical properties of nonwovens and water vapor transport rate was analyzed by Pearson Correlation. Steady and dynamic state water vapor transport properties were measured by absorption, evaporation and cobaltots chloride method respectively. The results were as follows: 1) In geometrical structure, thickness of nonwovens was effected on absorption and evaporation rate and air permeability was more influencing factor on water vapor transport rate than porosity. There were no decreasing of water vapor transport rate in hydrophilic fiber at high relative humudity. 2) The hydrophilicity of fiber affected steady and dynamic state water vapor permeabilities and wool nonwoven showed higher water vapor transport rate than polyester at high relative humidity. 3) Thickness showed higher correlation coefficient with water vapor transport rate than other physical properties of nonwovens.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.2
• /
• pp.55-63
• /
• 1985

This study is focused on deposition process leading to inefficiency and hot corrosion in fossil fuel-fired furnaces and engines. An improved understanding of the coupled thermodynamics, kinetics, and transport processes governing the deposition rate of inorganic oxides and salts from hot gases containing these compounds can suggest more efficient test strategies and control measures. Accordingly, an optical re-evaporation method for accurately measuring the growth rate of deposits under laboratory burner conditions has been developed. To demonstrate the technique and provide data suitable for theoretical model development, a deliberately simple chemical system and target geometry are used. Potassium sulfate(K$_{2}$SO$_{4}$)is introduced into a premixed propane-air flat flame at atmospheric pressure. The growth rate of $K_{2}$SO$_{4}$ on an electrically heated Pt ribbon is measured by re-evaporation technique.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.2-2
• /
• 1998

고체 추진제의 연소율(burning rate)은 연소의 동적 기동을 이해할 수 있을 뿐 아니라 추진제의 성능을 판단할 수 있는 중요한 수단이기 때문에 많은 연구가 진행되어 왔다. 특히 AP계의 고체추진제 표면에서는 발열반응인 분해반응(decomposition) 이외에도 기체로 증발되는 증발되는(evaporation or sublimation)이 존재한다. 증발반응으로 인하여 연소율은 외부압력의 변화에 대하여 반응하게 되며 실험적으로 $r_{b}$= a $p^n$의 관계를 보여주고 있다. 즉, 연소율(burning rate)은 연소실 압력 P의 n승에 비례하며 여기서 n은 실험적으로 결정되는 지수이다. 그러나 압력지수 n은 일반적으로 온도와 압력의 함수이기 때문에 실험적으로 이 측정하기는 매우 어려운 일이다. 또한 QSHOD 가정을 사용하여 고체 추진제의 연소 응답함을 해석하기 위해서 추진제의 민감계수(sensitivity parameters)에 관한 관계식이 필요하며 이러한 관계식은 추진제의 정상연소율에 관한 관계식으로부터 얻을 수 있다.다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.264-266
• /
• 2005

Manufacture of OLED device used thermal evaporation method. However thermal evaporation method has many defect as thermal damage of substrate, difficult of dopant rate control and low utilization of organic materials. so we suggest PLD(Pulsed Laser Deposition) method that solution of these problems. PLD method has many advantage as without thermal damage, easy indicate of deposition rate per one pulse and good utilization of organic materials. In this paper we apply the PLD method for manufacture of device so we present high efficiency device manufacture using PLD method that has good deposition uniformity, surface rough and deposition rate.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.2
• /
• pp.57-62
• /
• 2005

Using intense pulsed ion beam evaporation technique, we have succeeded in the preparation of poly crystalline silicon thin films without impurities on silicon substrate. Good crystallinity and high deposition rate have been achieved without heating the substrate by using lEE. The crystallinity of poly-Si film has been improved with the high density of the ablation plasma. The intense diffraction peaks of poly-Si thin films could be obtained by using the substrate bias system. The crystallinity and the deposition rate of poly-Si thin films were increased by applying (-) bias voltage for the substrate.

• Journal of the Korean Institute of Gas
• /
• v.5 no.2 s.14
• /
• pp.22-29
• /
• 2001

The number of gas containers and the period of exchanging gas containers are vsy important in designing liquefied petroleum gas(LPG) supply system for small capacity domain. And also the evaluation of remaining LPG in containers to be exchanged is very useful information in commerce. However seldon has been studied on calculating method about those with respect to gas consumption pattern. In this study, a simulation method was developed to estimate the evaporation capacity of LPG container, the mass gas flow rate from LPG container, the temperature and vapor pressure of LPG, and the remained LPG at containers to be exchange by using LPG property equations, mass balance equation, and heat balance equation. The simulation results were correlated well with experimental data. The overall heat transfer coefficient from air to LPG is approximately $9{\~}13 kcal/m^2{\cdot}hr{\cdot}^{\circ}C$ and does not strongly affect on the evaporation capacity of LPG container. The mass gas flow rate from LPG container is constant when the vapor pressure of LPG is within pressure regulator's control range. While, out of range, it suddenly reduce to a evaporation rate which is balanced with heat transfer from air. The evaporation capacity of LPG container increased with surrounding temperature and the composition of propane, and decreased drastically with continuous gas consumption. The number of gas containers divided the number of houses using gas supply system was reduced by using automatic gas feeding device.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.402-410
• /
• 2000

As the combustion process of CWM consists of the water evaporation, the release and combustion of volatile matter, and the combustion of char for every particle, it is more complex than that of existent liquid fuel. Though the many studies on CWM combustion have been carried out by the single droplet using hanging methods or the multiple droplet using atomization methods, any report don't presents definite solution about the effects by the initial water evaporation and combustion of volatile. When CWM is suddenly exposed in the high temperature surroundings, the internal water evaporates and then each droplet builds up pores. Besides, porosity rate changes along the temperature of surroundings, the composition ratio of CWM, and the initial diameter of droplet. In result, because it affects the whole combustion rate, the combustion of CWM has complex mechanism as compared with the combustion of liquid or gas fuel. Therefore, concentrating on porous structure of CWM, this study has proceeded to acquire the basic data on the CWM injection combustion and closely examines the effects of the first stage combustion on the whole combustion by measuring the diameter variations, pore rate, mass fraction burned, and the internal temperature changes of CWM droplet. The results demonstrate that $60{\sim}70%$ of initial mass is reduced during water evaporation and volatile combustion period, and swelling rate, mass faction burned, and density variation are greatly concerned with atomization of CWM etc.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.3
• /
• pp.105-109
• /
• 2008

Electrical characteristics of organic light-emitting diodes were investigated by varying a hole-size in evaporation boat in the device structure of ITO/tris(8-hydroxyquinoline) aluminum$(Alq_3)$/Al. The device was manufactured using a thermal evaporation under a base pressure of $5{\times}10^{-6}$ Torr. The $Alq_3$ emitting organics were evaporated to be a thickness of 100 nm at a deposition rate of $1.5{\AA}/s$. A cylindrical-shaped evaporation boat was made out of stainless steel with a small size of hole on top of the boat. Several evaporation boats were made having a different hole size on top; 0.8 mm, 1.0 mm, 1.5 mm, and 3.0 mm. We found that when the hole size on top of the evaporation boat is 1.0 mm, the average roughness is rather smoother compared to the other ones. Also, luminance and external quantum efficiency are superior to the others. Compared to the ones from the devices made with the hole-size of 0.8 mm boat. The luminance and external quantum efficiency of the device made with the hole-size of 1.0 mm boat were improved by a factor of seventy and thirty three, respectively. Also operating voltage is reduced to 2 V.