• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.2
• /
• pp.102-107
• /
• 2014

The engine excitation forces are considered as major vibration source for the forklift truck, especially in small class. Even though the current engine mounting system designs are acceptable for vibration isolation, the performance of the engine mounting system is still required for the tendency of light weight, higher power and driver's higher vibration requirement. In this paper vibration reduction technique of forklift engine which is supported on rubber mounts is presented. Based on the dynamic model of resilient engine mounting system, design evaluation program is established. The design optimization technique and evaluation method of system properties are discussed. Effects of optimal design are validated through comparison with test results.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.9
• /
• pp.470-474
• /
• 2004

Both ratio error and phase angle error in voltage transformer(VT) depend on values of burden of VT used. A method of evaluation for linearity of ratio error and phase angle error in VT measurement equipment have been developed using the standard resistance burdens, with negligible AC-DC resistance difference less than $10^-6$. These burden consists of five standard resistors, with nominal resistance of 100 $\Omega$, 1 k$\Omega$, 10 k$\Omega$, 100 k$\Omega$, and 1 M$\Omega$. The developed method has been applied in VT measurement equipment of industry and the validity of the developed method has been verified by showing the consistency of the result of linearity obtained using VT with wide ratio error.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.97-102
• /
• 2011

The size of TV and TFT-LCD are bigger and bigger for the next generation exposure equipment install that existing fab are getting a lot of additions. When the new fab build an extension that the shortening of the construction and non-vibration are use cast in place concrete pile method. In this study when lay the foundation of existing fab adjoin use vibration monitoring system are rotator type all casing method among cast in place concrete pile method. The evaluation of ground vibration of rotator type all casing method effect to precision equipment and vibration area of influence.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.227-230
• /
• 2009

Currently the country's foreign energy dependence reaches approximately 97% and the total energy consumption percentage of buildings(commercial and domestic parts) reaches approximately 24%. Building energy saving by enhanced insulation will be very important issue. Therefore, the solution is required to reduce energy loss and increasing displeasure caused by excessive influx of solar energy through windows, to solve the problems like decoloration on indoor furniture an clothes by harmful ultraviolet rays, air conditioning and increased cost. This research used for commercialization and ills semination by basic information through a evaluation on insulation performance of the window of high efficiency energy equipment which can improve the insulation performance.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.1488-1494
• /
• 2006

The most important thing to secure safety and reliability of railway vehicles is to verify performance characteristics of equipments, and related companies or research institutes had many efforts to verify performances and functions of equipments synthetically and efficiently. KHST(Korean High Speed Train) has been developed by KRRI(Korea Railroad Research Institute). An electric railway system is composed of high-tech subsystems, among which main electric equipment such as transformers and converter are critical components determining the performance of rolling stock. We developed a measurement system for on-line test and evaluation of performances of KHST. The measurement system is composed of software part and hardware part. Perfect interface between multi-users is possible. A new method to measure temperature was applied to the measurement system. By using the system, fault diagnosis and performance evaluation of electric equipment in Korean High Speed Train was conducted during test running.

• Magazine of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.10-12
• /
• 2013

• Ocean Systems Engineering
• /
• v.10 no.2
• /
• pp.163-179
• /
• 2020

Considering the huge demand of several types of subsea equipment, as Christmas Trees, PLEMs (Pipeline End Manifolds), PLETs (Pipeline End Terminations) and manifolds for instance, a critical phase is its installation, especially when the equipment goes down through the water, crossing the splash zone. In this phase, the equipment is subject to slamming loads, which can induce impulsive loads in the installation wires and lead to their rupture. Slamming loads assessment formulation can be found in many references, like the Recommended Practice RP-N103 from DNV-GL (2011), a useful guide to evaluate installation loads. Regarding to the slamming loads, RP-N103 adopt some simplifying assumptions, as considering small dimensions for the equipment in relation to wave length, in order to estimate the slamming coefficient C_S used in load estimation. In this article, an experimental investigation based on typical subsea structure dimensions was performed to assess the slamming coefficient evaluation, considering a more specific scenario in terms of application, and some reduction of the slamming coefficient is achieved for higher velocities, with positive impact on operability.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.302-307
• /
• 1998

In the production of semiconductor wafer, optical and electron microscopes, ion-beam, laser device must maintain their alignments within a sub-micrometer. This equipment requires a vibration free environment to provide its proper function. Especially, lithography and inspection devices, which have sub-nanometer class high accuracy and resolution, have come to necessity for producing more improved giga and tera class semiconductor wafers. This high technology equipments require very strict environmental vibration standard, vibration criteria, in proportion to the accuracy of the manufacturing, inspecting devices. The vibration criteria of high sensitive equipment should be represented in the form of exactness and accuracy, because this is used as basic data for the design of building structure and structural dynamics of equipment. The study on the evaluation of the factors affecting the permissible vibration criteria is required to design the efficient isolation system of the semiconductor manufacturing of equipment. This paper deals with the properties of the effected factor for vibration criteria of high sensitive equipment.

• Journal of Korean Institute of Industrial Engineers
• /
• v.27 no.3
• /
• pp.297-304
• /
• 2001

Procurement decisions for inspection equipment are often made heavily based on the initial purchase price instead of the effects of inspection cost, equipment calibration and utilization over the lifetime. Cost of ownership(COO) models that take into account all of these cost factors together have been developed focusing on a single quality characteristic. In modern manufacturing environment, inspection equipment often can deal with more than one quality characteristic simultaneously. In this paper, we propose the revised COO model for the economic evaluation of the inspection equipment that can accommodate multiple quality characteristics. We also employ an engineering economy model to compare equipments with different life span. Software is developed for handy comparison of the COO of alternative equipments along with sensitivity analysis far the optimal procurement decision.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.569-574
• /
• 2008

Nowadays, the equipment for a semiconductor process is required to raise accuracy and productivity. Therefore, the natural frequency of the equipment has been lowered because it has been precise, rapid, large, and light. In order to improve the efficiency of production, it is necessary for the equipment to increase the operation speed, which causes inevitable vibration problems. In this paper, influence analysis of ball-screw in the equipment and evaluation method for the vibration on the base are presented based on the analyses of dynamic characteristics for the mechanical structure through the modal test.