• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1012-1016
• /
• 2004

In this paper, we propose a simple but optimized NC code generating technique for disk cams by means of tool path error control in a five-axis CNC machining center. Using the geometric theorem of the triangle made between manufacturing points and error checkpoint, the tool path error has been studied for disk cams profile generation and an improvement in the profile has been obtained. Then, based on the present manufacturing approach a computer program is developed on $C^{++}$ language to perform and to verify the shape design, the manufacturing simulation, and the optimized generation of the NC code.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2431-2433
• /
• 1999

Phase errors of arrayed waveguide degrade the performance of AWG router, especially for dense WDM system. So it is necessary to measure the phase error and to compensate. The analysis method of the interference signal from the low coherence interferometer to measure the path length difference phase error is studied. The interference signal generated assuming the intentional path length difference errors of 0.1$\sim$0.4${\mu}m$ are analyzed and the results show that the path length difference phase error of ${\Delta}L$ within ${\pm}14^{\circ}$ of sampling phase error can be accurately measured.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.58-58
• /
• 2001

This paper shows a practical approach that is robust to the errors causing path-delay in mobile wireless location, and analyzes its performance by comparing with other methods. NLOS(non-line-of-sight) error and multipath are two big sources of positioning error in wireless location. Contrary to GPS(global positioning system), they result from the terrestrial propagation of a signal. Especially, since LOS(line-of-sight) path between a transceiver and a receiver is blocked by intermediate buildings and topography, NLOS causes a signal to be reflected and diffracted. This path-delay error is very localized, and so, it is not easy to be estimated and mitigated. To treat such localized error, therefore ...

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.2
• /
• pp.211-217
• /
• 2014

This paper addresses an algorithm of path planning for autonomous driving of a ground vehicle in waypoint navigation. The proposed algorithm is flexible in utilization under a large GPS positioning error and generates collision-free multiple paths while pursuing minimum traveling time. An optimal path reduces inefficient steering by minimizing lateral changes in generated waypoints along a path. Simulation results compare the proposed algorithm with the A* algorithm by manipulation of the steering wheel and traveling time, and show that the proposed algorithm realizes real-time obstacle avoidance by quick processing of path generation, and minimum time traveling by producing paths with small lateral changes while overcoming the very irregular positioning error from the GPS.

• The Journal of Korea Robotics Society
• /
• v.16 no.3
• /
• pp.250-259
• /
• 2021

Path planning is one of the important technologies for automated parking. It requires to plan a collision-free path considering the vehicle's kinematic constraints such as minimum turning radius or steering velocity. In a complex parking lot, Rapidly-exploring Random Tree^* (RRT^*) can be used for planning a parking path, and Reeds-Shepp or Hybrid Curvature can be applied as a tree-extension method to consider the vehicle's constraints. In this case, each of these methods may affect the computation time of planning the parking path, path-tracking error, and parking success rate. Therefore, in this study, we conduct comparative analysis of two tree-extension functions: Reeds-Shepp (RS) and Hybrid Curvature (HC), and show that HC is a more appropriate tree-extension function for parking path planning. The differences between the two functions are introduced, and their performances are compared by applying them with RRT^*. They are tested at various parking scenarios in simulation, and their advantages and disadvantages are discussed by computation time, cross-track error while tracking the path, parking success rate, and alignment error at the target parking spot. These results show that HC generates the parking path that an autonomous vehicle can track without collisions and HC allows the vehicle to park with lower alignment error than those of RS.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.50-55
• /
• 2004

Because of the development in mold industries, the geometrical form accuracy of the milled surface is getting more and more important. It has been known that the geometrical form accuracy is affected by machine conditions, cutting conditions, tool conditions and tool path and so on. Among them, the tool approaching path causes the change in material removal per tooth at the end of each machining cycle. And, this change generates the geometrical form error around the region where the tool engages the workpiece initially. So, it is impossible to eliminate the geometrical error caused by the tool approaching path. Thus, characteristics of this geometrical error are studied analytically and experimentally to minimize this region.

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.485-493
• /
• 1998

Many of the adaptive noise control systems utilize a form of the least mean square (LMS) algorithms. In the active control of noise, it is common practice to locate an error microphone far from the control source to avoid the near-field effects by evanescent waves. Such a distance between the control source and the error microphone makes a certain level of time-delay inevitable and, hence, may yield undesirable effects on the convergence properties of control algorithms such as filtered-x LMS. This paper discusses the dependence of the convergence rate on the acoustic error path in these popularalgorithms and introduces new algorithms which increase the convergence region regardless of the time-delay in the acoustic error path. Performances of the new LMS algorithms are presented in comparison with those by the conventional algorithms based on computer simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.843-845
• /
• 1995

There are a variety of trajectory and control algorithms available for robot trajectory tracking. Before using the enhanced trajectory and control algorithms to reduce the tracking error, we introduce the new method which reduces the tracking error by clipping the joint velocity. A lot of robot trajectory tracking methods are proposed to enhance the robot tracking, but irregular tracking errors are always accompanied. Up to now, these irregular tracking errors are gradually but uniformly reduced by introducing more complicated control algorithms. It is intuitively obvious to reduce only the big errors selectively in the irregular ones for the better performance. By heuristic method, big tracking errors in these irregular ones are assumed mostly due to the fast moving of joint with respect to the same tracking and control method. So, in this paper, we introduce a new method which reduce the big tracking errors by clippings the joint velocity with the constraint of given path. Using this method, desired trajectory tracking is obtained within the far reduced error bound. Also, this method is successfully applied to generate the path-constrained error reducing trajectories for 2-axis SCARA type robot.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.22-28
• /
• 2019

This paper presents the monitoring method of machining error and quality check to improve the productivity of boring manufacturing process. Machining error usually appears as the offset of spatial location of actual cutting path compared to ideal cutting path. In order to monitor an error of workpiece, multiple factors affecting quality of boring, such as distortion of workpiece, clamping error, radial rotation error of the spindle and motion error of machine tools, were took into account. To verify the productive quality, we propose the quality check system. The system based on IT convergence analyzes the process error rate and saves the analyzed data in memory. Also, these play important roles in detecting an inferior production goods and can decrease the production cost and loss of bearing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1542-1551
• /
• 1990

This paper shown how to measure the machining error in diameter of cylindrical workpiece and compensate the measured machining error in NC turning. Machining error is measured by the electric micrometer mounted on the tool post with the NC part program for probe location path analyzed. Correct NC part program for finish turning is automatically generated to compensate the measured machining error. These concepts have been effectively introduced to a newly developed software for error compensation. In turning experiments with the developed error compensation system, machining error was almost within the specified tolerance, which reveals the effectiveness of the developed system.