• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.61-68
• /
• 2019

Only the power is converted from AC to DC, in accordance with IEC 60587 based test method, in order to develop the LSR(Liquid Silicone Rubber) insulator material for HVDC, the experiment of Inclined Plate Tracking and Erosion Resistance was conducted. A contaminant (2.5 mS/cm: ammonium chloride) was applied at a rate of 0.3 ml/min and a voltage of ${\pm}3.5kV$, and was evaluated on the basis of 60 mA/2s. The samples were prepared by dispersing LSR/Nano silica_25wt% Composites in LSR. The erosion phenomena of surface discharge and tracking due to DC polarity and negative polarity were measured by image, leakage current maximum and thermal camera. The thermal imaging camera measured the surface temperature generated by the joule heat of the leakage current due to the drying discharge and the conductive current. After the measurement, the tracking and erosion mechanisms were evaluated for erosion weight, erosion depth and erosion length. Positive and negative polarity of LSR/Nano Silica_25wt% composite Tracking and erosion results show that positive polarity is more severe than negative polarity.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.2
• /
• pp.196-200
• /
• 1999

In the case that erosion and corrosion occurs in machinery and structure at the same time, the synergy effect by erosion-corrosion affects fatal effect to durability of machinery and structure. Therefore, in machinery and structure which use corrosion liquid, the study of the synergy effect of erosion-corrosion which affects metal material is requested. In this paper. the flow corrosion experiment about the effect of temperature change and liquid velocity change in sea water was carried out to study the characteristics of erosion-corrosion for tube material Cu heat exchanger The main results obtained are as follows. (1) Damage appearance of tube outside by erosion-corrosion becomes dull because electrode potentials of Cu tube is higher than electrode potential of STPG38 shell. (2) In the cooling system by sea water, the weight loss rate of Cu at tube outside liquid temperature of $70^{\circ}C$ is higher than that of temperature of $20^{\circ}C$. (3) In cooling system by sea water, the weight loss rate of Cu at liquid velocity of 5.1m/s is higher than that of velocity of 1.47m/s. But as the testing time passed, the weight loss rate of Cu at velocity of 5.1m/s is almost steady and becomes dull at velocity of 1.47m/s.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.218-224
• /
• 2006

The sludge oils were produced necessarily in the ships operation, so that it will be the best way to manage the sludge oils inside ship itself from a viewpoint of the prevention of marine oil pollution. The ultra-sonic breaking system which recycle the sludge oil from ship into usable oil to be brunt is recognized as a most possible recycling device. In this regards, the purpose of this study is to examine erosion damage,on the SS400 specimen by cavitation and the effect of impact pressure generated from the demolition of the cavity of ultrasonic vibration in the marine sludge oil environment.. The erosion damage of specimen was investigated mainly on weight loss, weight loss rate and maximum erosion rate with variation of the oil temperature as well as the change of space between transducer hem and specimen. The experimental results showed that as the space between ultrasonic vibrator horn and specimen disk increased, the weight loss and weight loss rate decreased and the values were larger in SFO than in SLO. The experimental results can be useful to the development of sludge oil disposing systems and to consider a countermeasure for the prevention of erosion damages by cavitation.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.7 no.3
• /
• pp.75-84
• /
• 2001

Ultrasonic vibrator is an equipment which atomizes and homogenizes the oils by breaking the oil particles with ultrasonic vibration cavity, and possibly improves the properties. There are various parameters on the effect of ultrasonic irradiation. Especially, this study intended to investigate the matrix structure of sludge oils and the erosion damages for horn disc SS41 according to the variation of the oil temperature and the immersing depth of horn disc. Sludge oils were irradiated with ultrasonic vibration and then observed the aspects of the change of oil particles. From these, the recycling feasibility of sludge oil for useable oil to be burnt was determined. The erosion damages for horn disc SS41 were examined with weight loss, weight loss rate and the irradiation time to max. erosion rate. These data will be useful to the development of ultrasonic breaking systems to recycle sludge oil and to consider a countermeasure for the prevention of erosion damages.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.4
• /
• pp.295-297
• /
• 2000

A new method to evaluate erosion of biodegradable polymer, polyanhydrides, was developed. The polymer devices were prepared with the melt-casting method and weight loss was accurately measured after agitating the devices in buffers (pH 1-9), and removing the device at selected time intervals and freeze-drying the device. The erosion rate was estimated from the plot of the weight loss(%) of device as a function of time. The freeze-drying technique used in this study is particularly useful for estimating the erosion rate of biodegradable polymer.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.4
• /
• pp.287-299
• /
• 2016

In China, agricultural irrigation water often contains a lot of suspended sediment which may cause the nozzle wear. In this study, a new numerical simulation combing the Discrete Phase Model and a remeshing algorithm was conducted. The geometric boundary deformation caused by the erosion wear, was considered. The weight loss of the nozzle, the node displacement and the flow field were investigated and discussed. The timestep sensitivity analysis showed that the timestep is very critical in the erosion modeling due to the randomness and the discreteness of the erosion behavior. Based on the simulation results, the major deformation of the boundary wall due to the erosion was found at the corners between outlet portion and contraction portion. Based on this remeshing algorithm, the simulated erosion weight loss of the nozzle is 4.62% less compared with the case without boundary deformation. The boundary deformation changes the pressure and velocity distribution, and eventually changes the sediment distribution inside the nozzle. The average turbulence kinetic energy at the outlet orifice is found to decrease with the erosion time, which is believed to change the nozzle's spray performance eventually.

• Journal of Fisheries and Marine Sciences Education
• /
• v.11 no.2
• /
• pp.139-149
• /
• 1999

Thermal sprayed Ni-Cr alloy coating on the carbon steel was carried out erosion-corrosion test and electrochemical corrosion test in the marine environment. The erosion-corrosion behavior and electrochemical corrosion characteristics of substrate(SS400) and thermal sprayed Ni-Cr coating was investigated. The erosion-corrosion control efficiency of Ni-Cr coating to substrate was also estimated quantitatively. The main results obtained are as follows : 1) The weight loss rate of Ni-Cr coating layer by the erosion-corrosion compared with substrate was smaller. With the lapse of time, the weight loss rate of substrate was linearly increased in $25{\Omega}{\cdot}cm$ solution, but that of Ni-Cr coating became stable. 2) The corrosion potential of substrate became less noble than that of Ni-Cr coating layer, and the corrosion current density of Ni-Cr coating became lower than that of substrate. 3) The control efficiency of erosion-corrosion of Ni-Cr coating compared to substrate became more dull than that of corrosion in $25{\Omega}{\cdot}cm$ and $5000{\Omega}{\cdot}cm$ solution.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.3
• /
• pp.42-49
• /
• 1993

Recently, because the lubricating oil showed a tendency to be emulsified and oxidized by high speed, high output and the extension of maintenance & conservation of marine engine, the cavitation erosion-corrosion at such an environment became a big problem on effective performance of engine. Therefore, there was a need to study the behavior and protection of erosion-corrosion damage, and then applied inhibitor to a protective method of cavitation erosion- corrosion damage. At this time, test environments were marine lubricating oil & various emulsified oil that mixed distilled water and sea water etc., and also used 20KHz, 24.mu.m piezoelectric vibrator as an experimental apparatus of cavitation erosion. With this apparatus, we investigated an influence of the emulsified oil on characteristics of erosion-corrosion and protection for erosion-corrosion by inhibitor at slide bearing metals.

• Journal of Welding and Joining
• /
• v.5 no.2
• /
• pp.27-34
• /
• 1987

The characteristics of arc sprayed layer were studied with hardness test and microstructural observation. The erosion resistance of arc sprayed layer was also evaluated using a method of steel ball blasting test which was proposed in this study as a test method for measuring the erosion properties in the impact wear condition. By an impact of the molten droplets on the redeposited substrate, lamella structure was formed which contains laminated oxide layers, fissures, and porosities. As a result of mechanical tests, it was shown that the sprayed specimen showed higher hardness than the substrate, but it resulted in higher erosion rate than the substrate. The poor erosion property obtained with a sprayed coating was considered to be attributable to easy flaking off the the layers laminated with brittle oxide layers.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.2
• /
• pp.11-17
• /
• 1990

The erosion characteristice of plasma-sprayed tungsten carbide chromium carbide coatings were investigated. Erosion tests were perfomed at room temperature by using Al2O3 and SiC particles accleerated in air stream. Weight losses of the coatings were measured over a range of paricle velocities and impingement angle. It was found that, for both of this coatings, the maximum erosion occurrd at a normal angle of impact, and the erosion rate at this impact angle was a power function of pparticle velocity. The values of the velocty emponent were between 3.07 and 3.50 Erosion value of chromium carbide coating was higher than that of tungsten carbide coating.