• Laser Solutions
• /
• v.13 no.3
• /
• pp.7-12
• /
• 2010

In this study, laser welding of aluminum AA5182 with AA5356 filler wire was carried out and the formability of the weld joint was evaluated through Erichsen test according to laser power, welding speed and wire feed rate. Fracture was occurred in both directions, perpendicular and parallel to the weld line at 0.75 of Erichsen ratio. Second order Regression model to estimate Erichsen ratio with experimental variables was proposed and the performance of model was evaluated with F-test and average error rate.

• Transactions of Materials Processing
• /
• v.9 no.5
• /
• pp.463-468
• /
• 2000

An experimental study has been performed to investigate the forming characteristics of pre-coated metals(PCMs) widely used in domestic appliances through Erichsen tests and deep drawing tests. Erichsen tests are performed to find out the forming limits of seven pre-coated metals in normal conditions. Rectangular deep-drawing tests are carried out to know the effects of die materials and blank metals on forming loads and surface defects of final PCM products. In the deep-drawing test, four die materials ［STD11(TiCN), STD11, STD11(TD), AMPCO] are used. In the Erichsen test, the forming limits of PCMs are obtained from flaking or crack of pre-coated films and lower than those of base metals. In respect of surface roughness and forming load, STD11(TD) and AMPCO materials are superior to my other die-materials used in the deep-drawing test.

• Transactions of Materials Processing
• /
• v.20 no.8
• /
• pp.568-574
• /
• 2011

The combination of tailor welded blank (TWB) and hot stamping often offers improved crash-worthiness and reduced mass of stamped parts in the automobile body. To investigate the formability of laser TWB and the reliability of weld line, the present study used 22MnB5 boron steel sheet of the same thickness and used the Erichsen cupping test at elevated temperatures. The effects of laser direction, die temperature, weld line positions and forming speed on formability(the limiting dome height) were studied and the results were compared with the formability of the base material.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.89-93
• /
• 2002

A study of noticeable improvement in welding speed in thin-plate Type 304 stainless steels gas tungsten arc (GTA) welding was investigated. The welding speeds were increased to more than 3m/min, up to 8m/min. During the welding, Direct Current Straight Polarity (DCSP) and pulsed current GTA welding processes were carried out, respectively. The appropriate high speed welding parameters were established while achieving a high quality weld. After this, Erichsen test and tensile test were performed. The results obtained wert summarized as following: ultra high speed welding for thin-plate Type 304 could be satisfactorily welded with high speed from 3m/min to 8m/min in both DCSP and pulsed GTA welding; Increasing welding speed was found to decrease the ductility, tensile strength md elongation of welded joint; The optimal frequency would be 200Hz-500Hz for high speed welding in pulsed current welding; DCSP welding could obtain the better results of Erichsen test and tensile test than those of pulsed current welding obtained.

• Transactions of Materials Processing
• /
• v.9 no.6
• /
• pp.582-589
• /
• 2000

In recent automotive industry, vehicle weight can be reduced by one-step forming of tailored blanks welded with two or more sheets of metal blanks. Mash seam welding shows an overlap joint, a much wider welding area, and heat affected zone(HAZ) than a laser welding. This paper deals with the forming characteristics of mash seam welded tailored blanks. Mash seam welded blanks of same or different thickness combinations were prepared, and tensile, hardness, erichsen, and dome stretching tests were done.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.138-140
• /
• 2007

This study aimed to evaluate the low temperature properties of the 18Cr ferritic stainless steel weld. Applied welding methods were LB(Laser Beam) and GTA(Gas Tungsten Arc) welding to compare the different low temperature properties of the welds. Low temperature properties were evaluated by the Charpy impact, Erichsen and Expansion test at low temperature. LB weld showed superior low temperature properties in the cases of the Charpy impact test and expansion test at low temperature, while GTA weld showed a superior low temperature property in the case of Erichsen test at low temperature. The different low temperature properties with test methods are still under analysis and may be due to different crack path depending on the microstructure, test speed and stress concentration during test.

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.23-28
• /
• 2003

The effect of the welding speeds on the weld bead shape, microstructure, and mechanical properties in type 304 austenitic stainless steels was investigated by microscopic test, Erichsen test and tensile test. In this study welds were produced using autogeneous Direct Current Straight Polarity (DCSP) and pulsed current GTA welding. This study shows the ferrite content, ductility, tensile strength and elongation of high speed welds are decreased with increasing welding speed. The high speed welds exhibits satisfactory tensile strength, though the ductility is not good as that of the base metal.

• Laser Solutions
• /
• v.2 no.1
• /
• pp.61-67
• /
• 1999

This study introduces the new concept in the evaluation criteria of the $CO_2$ laser Tailored Blank weldability, The materials used are 0.7mm, 1.5mm thick low carbon automotive galvanized steels. Welding tests were conducted for both similar thickness(0.7mm-0.7mm, 1.5mm-1.5mm) and dissimilar thickness(0.7mm-1.5mm) cases. The criteria developed for optimum welding conditions were based on relationship between results of die press forming test, weld transverse tensile test Erichsen test and weld penetration measurements. Application of the developed criteria(fracture ratio, strength ratio and D/To) in obtaining optimum welding condition revealed that a weld which satisfied any of the criteria did not fracture during actual die press test.

• Transactions of Materials Processing
• /
• v.21 no.4
• /
• pp.258-264
• /
• 2012

The forming failure of AZ31 alloy sheet during deep drawing processes was predicted by the FEM and ductile fracture criteria. Uniaxial tensile tests of round-notched specimens and FE simulations were performed to calculate the critical damage values for three ductile fracture criteria. The critical damage values for each criterion were expressed as a function of strain rate at various temperatures. In order to determine the best criterion for failure prediction, Erichsen cupping test under isothermal conditions at $250^{\circ}C$ were conducted. Based on the plastic deformation histories obtained from the FE analysis of the Erichsen cupping tests and the critical damage value curves, the initiation time and location of fracture were predicted under bi-axial tension deformation. The results indicate that the Cockcroft-Latham criterion had good agreement with the experimental data. In addition, the FE analysis combined with the criterion was applied to another deep drawing process using an irregular shaped blank and these additional results were verified with experimental tests.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.236-239
• /
• 2000

It is important to evaluate austenitic heat resistant stainless steel because of low weldability of austenitic heat resistant stainless steel containing high Si. This study took varestraint test for evaluation of solidification cracking sensitivity and Erichsen test for evaluation of weld metal ductility. As a result of tests, solidification crack sensitivity increased with adding $N_2$ to shielding gas, and W had detrimental effect on crack resistance, but Ce had beneficial effect on crack resistance. Under same heat input, ductility of weld metal increased with welding speed.