• ETRI Journal
• /
• v.33 no.2
• /
• pp.176-183
• /
• 2011

This paper presents a new analytical approach and experimental verification for the improvement of noise performance in phased-array receivers. For analysis purposes, a multi-channel array system is converted into an equivalent single-channel system, such that the two presents the identical signal and noise powers at the output, respectively. We define an effective gain, noise figure, and signal-to-noise ratio in the equivalent system. Through the proposed approach, the noise performance of the array receiver is analyzed in a general and straightforward manner and then compared to that of each individual array channel. In addition, the phase noise of the array system is analyzed in a rigorous manner, showing its effective reduction by a factor of the array size. The predicted improvement of the noise performance is experimentally confirmed with a CMOS integrated phased-array receiver.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.243-246
• /
• 2004

The dynamic characteristic of a wrist power transmission examine closely with mass property, to present the model which induce the vibration is ultimately the purpose. A robot wrist power transmission for analysis model got the mass property through the approach to be the experimental. A bearing equivalent stiffness which supports the axis and a gear contact equivalent stiffness are determined by the simplicity analysis model compared the result of the experiment. We calculate the vibration tendency of the robot wrist power transmission by an analysis tool which is called the RecurDyn. We compared it with a signal analysis experiment's which a robot operation happens which is based on the ambient noise.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2003.11a
• /
• pp.95-100
• /
• 2003

The purpose of this study is to evaluate the noise environment of one-room type multi-family housing around the campus. The field measurements on equivalent noise level of indoor and outdoor were carried out in 6 subject house units during the 26th${\sim}$28th of November 2002. The results are as follows. 1) Outdoor noise levels of 6 subject buildings were distributed 52.8${\sim}$65.3dB(A) and were inappropriate to the standard for environmental noise, 55dB(A). 2) Indoor noise level of 6 subject house units were measured 27.5${\sim}$63.5dB(A). These values were higher than the indoor noise standard (40dB(A)) except subject house D(average 37.6dB(A)). 3) It was found that the differences of indoor noise levels between subject house units were caused by resident's living factor, characteristics of window, and existence of balcony.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.252-257
• /
• 2006

Low vibration characteristics of a vehicle are mainly influenced by the local stiffness of the joint structure beam section. The method of substituting equivalent beam element to spring element for the joint is presented. Formation process of the equivalent beam joint modeling is described in terms of key section properties. To get required dynamic characteristics section properties of the equivalent beam element are set to design variables. The study shows that the equivalent beam joint model can be effectively used for low frequency vibration analysis of a vehicle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.229-229
• /
• 2006

WECPNL(Weighted Equivalent Continuous Perceived Noise Level) which designated currently in Domestic 'The Stanrd Method of Measuring Noise and Vibration' is composed of different factor with WECPNL that published in ICAO. Domestic WECPNL is concerned in application of $L_{MAX}$ measurement. On the other hand, ICAO's WECPNL is based on EPNL that includes factors of the pure tone correction and the duration time. NNI and NEF also are each based on PNL and EPNL. Because a military aircraft noise, especially, has the pure tone of high frequency and the irregular duration, it seems to be undesirable to estimate aircraft noise for using Domestic WECPNL. Therefore, this study was performed to detect a flaw of Korean WECPNL, through comparison of the trend of each other aircraft noise index by using equivalent rawdata.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.3
• /
• pp.6-11
• /
• 1977

The noise behavior of the Schottky Barrier Gate FET has been investigated by the use of noise equivalent circuit. It has been found that an additional noise source has to be taken into account in the GaAs SBGFET's biased in the pinch-off region; the intervalley scattering noise and the hot electron noise. In this paper, a noise equivalent circuit has been used to determine the noise parameter which was taken into account influence of the saturation velocity of carrier and parasitic resistance.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.2
• /
• pp.60-65
• /
• 1992

The roll response of a ship to random beam seas is investigated in terms of the threshold crossing process. The non-white excitation process is modeled as an equivalent white-noise one based on the assumption that the upcrossing properties of the response can be approximately replaced by the excitation with a white noise process with a suitable intensity. Then the non-linear damping is reinstated. The reinstated equation of motion with the equivalent white-noise intensity is solved using the equivalent non-linear method to get the desired probability density function. The proposed scheme is tested extensively with varing coefficients.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.12
• /
• pp.43-49
• /
• 2012

Noise measurements were performed by distance for major construction equipment. especially, For construction equipment that large width of variations is depending on the type of work, noise measurements were performed by the detail type of work. For a time of quiescent and construction, "A" compensation equivalent noise level (Leq) were measured. Most of the construction equipment and the characteristics of the point source appears to be similar in analyzed noise measurement results.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.212-216
• /
• 2001

Because conventional switching converters have been usually using unbalanced circuit topologies, parasitic capacitance between the drain/collector of an active switch and the frame ground through its heat sink may generate the common-mode conducted noise. We have proposed a balanced switching converter circuit, which is an effective way to reduce the common-mode conducted noise. As an example, a boost converter version of the balanced switching converter was presented and the mechanism of the common-mode noise reduction was explained using equivalent circuits. This paper extends the concept of the balanced switching converter circuit and presents a buck-boost converter version of the balanced switching converter. The feature of common-mode noise reduction is confirmed by experimental results and the mechanism of the common-mode noise reduction is explained using equivalent circuits.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.973-979
• /
• 1995

The input equivalent noise charge (ENC) of hydrogenated amorphous silicon radiation detector diodes was measured and analyzed. The noise sources of amorphous silicon diodes were analyzed into three sources; shot noise, flicker noise and thermal noise from the contact resistance. By comparing the measured ENC with the calculated signal charge in uniform generation case, the signal-to-noise ratio (S/N) for the sample diodes is estimated as a function of the detector bias and the shaping time of Gaussian pulse shaper. The maximum S/N occurred at the bias level just above the full depletion voltage for shaping time of 2∼3 ${\mu}$sec. The developed method is useful in optimum design or amorphous silicon p-i-n diodes for charged particulate radiation spectroscopy.