• Journal of Korean Association for Spatial Structures
• /
• v.19 no.2
• /
• pp.73-81
• /
• 2019

The high-temperature properties of mild steels were studied by comparing the test results of Kwon and the yield strength, tangent modulus predicted by the design provisions of ASCE and Eurocode(EC3). The column strengths for steel members at high temperatures were determined by the elastic and inelastic buckling strengths according to elevated temperatures. The material properties at high temperatures should be used in the strength evaluations of high temperature members. The buckling strengths obtained from the AISC, EC3 and approximate formula proposed by Takagi et al. were compared with ones calculated by the material nonlinear analysis using the EC3 material model. The newly simplified formulas for yield stress, tangent modulus, proportional limit and buckling strength which were proposed through a comparative study of the material properties and buckling strengths. The buckling strengths of proposed formulas were approximately equivalent to ones obtained from the formulas of Takagi et al. within 4%. They were corresponded to the lower bound values among the buckling strengths calculated by the design formulas and inelastic buckling analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.292-293
• /
• 2006

We have Investigated dielectric properties depending on bias voltage in organic lightemitting diodes using 8-hydroxyquinoline aluminum($Alq_3$) as an electron transport and emissive material. We analyzed the dielectric properties of organic light emitting diodes using impedance characteristics measurement by the auto-balancing bridge technique and equivalent cirrcuit of ITO/$Alq_3$/Al. Impedance characteristics was measured complex impedance Z and phase ${\theta}$ in the frequency range of 40 [Hz] to $10^8$ [Hz]. We obtained complex electrical conductivity, dielectric constant, and loss tangent ($tan{\delta}$) of the device at room temperature. From these analyses, we are able to interpret a conduction mechanism and dielectric properties contributed by an interfacial and orientational polarization.

• Journal of Welding and Joining
• /
• v.28 no.2
• /
• pp.39-46
• /
• 2010

IIn this study, used is the equivalent loading method based on the inherent strain to predict the welding deformation of panel members. Equivalent loads are computed from the inherent strain distribution around weld line, and then applied for the linear finite element analysis. Thermal deformation of panel members can be, of course, carried out through the rigorous thermal elasto-plastic analysis procedure but it is not practical in applying to predicting the welding deformation of large structures such as blocks found in a ship structure from view of computing time. The present equivalent load approach has been applied to flat plate model to verify the present approach, and to several curved plate models having the curvature in the welding direction to investigate the effect of the longitudinal curvature upon the weld-induced deformation. The results are compared with those by thermal elasto-plastic analysis. As far as the present results are concerned, it can be said that the present approach shows good agreement with the results by welding experiment and the rigorous thermal elasto-plastic analysis. The present approach has been also applied to predict the welding deformation of panel block as for application illustration to practical model.

• Structural Engineering and Mechanics
• /
• v.56 no.1
• /
• pp.137-156
• /
• 2015

In this paper, an analytical solution of displacement, strain and stress field for rotating thick-walled cylinder made of functionally graded material subjected to the uniform external magnetic field and thermal field in plane strain state has been studied. Stress, strain and displacement field as a function of radial coordinates considering magneto-thermo-elasticity are derived analytically. According to the Maxwell electro-dynamic equations, Lorentz force in term of displacement is obtained in cylindrical coordinates. Also, symmetric temperature distribution along the thickness of hollow cylinder is obtained by solving Fourier heat transfer equation in cylindrical coordinates. Using equation of equilibrium and thermo-mechanical constitutive equations associated with Lorentz force, a second-order inhomogeneous differential equation in term of displacement is obtained and will be solved analytically. Except Poisson's ratio, other mechanical properties such as elasticity modulus, density, magnetic permeability coefficient, heat conduction coefficient and thermal expansion coefficient are assumed to vary through the thickness according to a power law. In results analysis, non-homogeneity parameter has been chosen arbitrary and inner and outer surface of cylinder are assumed to be rich metal and rich ceramic, respectively. The effect of rotation, thermal, magnetic field and non-homogeneity parameter of functionally graded material which indicates percentages of cylinder's constituents are studied on displacement, Von Mises equivalent stress and Von Mises equivalent strain fields.

• Composites Research
• /
• v.18 no.5
• /
• pp.21-26
• /
• 2005

The validity of Eshelby-type model with Mori-Tanaka's mean field theory to predict the effective material properties of composites have been investigated in terms of filler size and its arrangement. The 2-dimensional plate composites including constant volume fraction of fillers are used as the model composite for the analytical studies, where the filler size and its arrangement are considered as parameters. The exact effective material properties of the composites are computed by finite element analysis(FEA), which are compared with effective material properties from the Eshelby-type model. Although the fillers are periodically or randomly arranged, the average Young's moduli by Eshelby-type model and FEA are in good agreement, specially for the ratio of specimen size to filler size being smaller than 0.03. However, Poisson's ratio of the composite by the Eshelby-type model is overestimated by $20\%$.

• Journal of the Korean Society of Radiology
• /
• v.17 no.6
• /
• pp.985-991
• /
• 2023

A tissue-equivalent phantom is necessary for quality control of hyperthermia therapy. However, since there is no phantom for this purpose, phantoms made from agar are being used in various studies. The tissue-equivalent properties of the agar phantom were confirmed by comparison with the tissue-equivalent material bolus in this study. CT images of the agar phantom and bolus were acquired, and tissue equivalent characteristics were analyzed with image analysis and dose calculation using a computerized radiation therapy planning system. The average pixel value was 96.960±10.999 in bolus, 108.559±8.233 in 3% agar phantom, and 111.844±8.651 in 4% agar phantom. Using the SSD technique, 100 cGy was prescribed at a depth of 1.5 cm and 6 MV X -ray was set to irradiated to 10x10 cm2, and the absorbed dose according to depth was calculated from the central axis of the beam. The intraclass correlation coefficient of dose distribution of bolus, 3% agar phantom, and 4% agar phantom was 0.979 (p<.001, 95%CI .957-.991). The density (g/cm3) at the point where the absorbed dose was calculated was 0.990±0.020 at the bolus, 1.018±0.020 at the 3% agar phantom, and 1.035±0.024 at the 4% agar phantom. In this study, the internal density distribution and uniformity of the agar phantom were confirmed to be appropriate as a tissue equivalent material by analysis of CT images and a computerized radiation therapy planning system.

• Advances in materials Research
• /
• v.3 no.2
• /
• pp.77-89
• /
• 2014

In the present article, the thermal buckling of zigzag single-walled carbon nanotubes (SWCNTs) is studied using a nonlocal refined shear deformation beam theory and Von-Karman geometric nonlinearity. The model developed simulates both small scale effects and higher-order variation of transverse shear strain through the depth of the nanobeam. Furthermore the present formulation also accommodates stress-free boundary conditions on the top and bottom surfaces of the nanobeam. A shear correction factor, therefore, is not required. The equivalent Young's modulus and shear modulus for zigzag SWCNTs are derived using an energy-equivalent model. The present study illustrates that the thermal buckling properties of SWCNTs are strongly dependent on the scale effect and additionally on the chirality of zigzag carbon nanotube. Some illustrative examples are also presented to verify the present formulation and solutions. Good agreement is observed.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.121-129
• /
• 1994

The Finite Element Method(FEM), which is existing stress analysis method, requires substantial amounts of efforts for analysis of perforated plates. An equivalent solid plate analysis method is developed in this paper. A perforated plate is assumed to be an equivalent solid plate in this method. Stress analysis is performed for this equivalent solid plate using effective material properties, and then these stresses are converted to the actual stresses of the original perforated plate. A case study is conducted for a rectangularly arrayed perforated plate using the proposed method in this paper. Compared and analyzed with respect to those calculated by the existing stress analysis method, the result seems to be satisfied in terms of its practicality and more conservative with respect to margin in design application.

• Journal of Applied Reliability
• /
• v.11 no.4
• /
• pp.357-369
• /
• 2011

Eco-robot for collecting recycling products is the machine which collects non-industrial wastes such as cans, PET bottles and etc. to reuse them as recycling resources. This eco-robot is operated in the condition that it should compress and hold various products without knowing their geometric shapes and material properties. For this reason reliability problems like malfunction or failure. comes to emerge, but the reliability test conditions to assess its performance and durability have not been founded yet. Therefore in this research failure mechanism of the eco-robot was analyzed and life test equipment which can reproduce actual usage conditions was developed. The compression levels in the life test were determined by measuring the crushing force acting on test products and Furthermore the test specimens which have equivalent shape and material properties with those of cans and PET bottles were proposed by simulating the deformation characteristics so that the actual compression conditions were set up in the test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.171-174
• /
• 1998

Quartz crystal in contact with viscoelastic medium is described directly in terms of the electrical equivalent circuit of the system. Stearic acid is used as viscoelastic medium and deposited on the surface of quartz crystal using the Langmuir-Blodgett(LB) method. Impedance properties of quartz crystal coated with LB films which were investigated and the possibility of applying the technique to chemical sensing introduced.