• 수산해양교육연구
• /
• 제28권5호
• /
• pp.1470-1477
• /
• 2016

This study has designed and evaluated the safety of watertight damper for Offshore Rigs. The watertight damper is an improved design for conventional DN 350 butterfly valve. Numerical analysis has been performed to investigate the safety factor and seat leakage of the designed 3-type disk dampers. The structure analysis results present the deformations, the equivalent stresses and the safety factor. It was confirmed that the designed disk, rib-disk and streamlined disk of watertight damper are safe enough in maximum operating pressure of 0.98MPa. The results show that the disk damper had the smallest maximum deformations and stress among 3-type disk dampers and the safety factor was 4.3. Therefore it is confirmed that the disk damper has the most excellent strength. Also linear static structural analysis was individually conducted for disk and body. The results show that the maximum disk deformation was larger than the body deformation, Therefore the disk damper is causes no seat leakage.

• 한국방재학회 논문집
• /
• 제8권2호
• /
• pp.45-49
• /
• 2008

본 논문에서는 미국 AISC-LRFD기준에서 제시하고 있는 웨브 변단면 I형 보의 탄성 좌굴강도 산정식을 고찰하였다. 미국 AISC-LRFD 기준의 기본 개념은 웨브 변단면 보를 가장 작은 단면과 동일한 크기를 가지면서 길이가 다른 등가 일정단면보로 대치하는 것이다. 또한 비지지 구간에 작용하는 응력 구배와 이웃한 보의 횡방향 구속효과를 고려하기 위하여 수정계수(B)를 적용하고 있다. AISC-LRFD 기준에 제시된 수정계수(B)와 유한요소해석결과와의 비교를 통해 본 논문에서는 수정계수(B)를 산정하기 위한 재 정의된 방법을 제안하였다.

• Steel and Composite Structures
• /
• 제36권3호
• /
• pp.339-353
• /
• 2020

This study investigates the seismic performance of steel reinforced concrete (SRC) T-shaped columns under low cyclic loading tests. Based on test results of ten half-scale column specimens, failure patterns, hysteretic behavior, skeleton curves, ultimate strength, ductility, stiffness degradation and energy dissipation capacity were analyzed. The main variables included loading angles, axial compression ratios and steel ratios. The test results show that the average values of the ductility factor and the equivalent viscous damping coefficient with respect to the failure of the columns were 5.23 and 0.373, respectively, reflecting good seismic performance. The ductility decreased and the initial stiffness increased as the axial compression ratio of the columns increased. The strength increased with increasing steel ratio, as expected. The columns displaced along the web had higher strength and initial stiffness, while the columns displaced along the flange had better ductility and energy dissipation capacity. Based on the test and analysis results, a formula is proposed to calculate the effective stiffness of SRC T-shaped columns.

• 한국지반환경공학회 논문집
• /
• 제20권5호
• /
• pp.13-21
• /
• 2019

급경사($65^{\circ}{\sim}85^{\circ}$)로 자연환경에서 장기간 안정한 상태로 유지되고 있는 깎기 또는 자연 상태의 암반사면이 다수 존재한다. 설계 실무측면에서 이와 유사한 암반상태 및 지질구조로 이루어진 지반을 양호한 연속체 암반사면으로 정의하고 있으며, 이 암반사면의 경사 결정 과정 중에 설계 및 시공 초기 단계의 안정해석 절차 단계에서 연속체 암반의 지반특성 평가방법을 수립하는 것이 중요하게 될 것이다. 이 연구에서는 급경사로 설계 가능한 양호한 연속체 암반사면의 안정해석 과정에서 지반정수 적용에 필요한 강도정수를 Hoek-Brown 파괴기준을 활용하여 실무적으로 산정하는 방안을 제안하고 이와 함께 급경사 암반사면의 안정해석을 통해 설계 적용성을 평가하였다. 기존 강도정수 산정방법은 작은 구속응력 변화에도 H-B파괴 포락선에 상응하는 등가 M-C강도정수가 민감하게 변화하므로 설계에서 실무적으로 활용하기가 부적합하였다. 이 문제점을 보완하기 위해 등각분할법으로 등가 M-C강도정수를 산정하는 방안을 제시하였다. 등각분할법의 설계 적용성을 확인하기 위해 기존 실시설계 현장에서 조성된 깎기 사면의 경사 변화에 따른 안전율 및 변위 결과를 검토하였다. 안전율은 1:0.5 사면에서 Fs=16~59이고, 1:0.3 사면에서 Fs=12~52이며, 대부분 10~12%의 감소를 보인다. 변위는 1:0.5 사면에서 0.126~0.975mm이고, 1:0.3 사면에서 0.152~1.158mm이며, 10~15%의 증가를 나타낸다. 이는 정규 비례의 미미한 변화이며, 안정성 측면에서는 양호한 상태이다. 설계 실무측면에서, H-B파괴기준에서 유도된 등각분할법으로 산정한 강도정수를 연구대상 암반사면과 유사한 양호한 암반에 대해 범용적인 강도정수로 적용하여도 안정적이고 경제적인 결과를 도출할 수 있다는 것을 확인하였다. 암반사면에 영향을 미치는 단층이 분포하지 않는 지반에서는 한계평형해석(LEM)과 유한요소해석(FEM)으로 안정해석하는 절차도 실무적으로 무난한 것으로 검토되었다. 연구대상 사면을 양호한 상태의 암반조건으로 선정하여 연구를 수행하였으나 좀 더 다양한 암반조건(터널 포함)에 보편적으로 적용할 수 있는지에 대한 검증 작업은 추후 연구과제가 될 것이다.

• Earthquakes and Structures
• /
• 제14권5호
• /
• pp.411-424
• /
• 2018

This study explores the inelastic behavior of systems with flexible base. The use of a single degree of freedom system (ESDOF) with equivalent ductility to represent the response of flexible base systems is discussed. Two different equations to compute equivalent ductility are proposed, one which includes the contribution of rigid body components, and other based on the overstrength of the structure. In order to asses the accuracy of ESDOF approach with the proposed equations, the behavior of a 10-story regular building with reinforced concrete (RC) moment resisting frames is studied. Local and global ductility capacity and demands are used to study the modifications introduced by base flexibility. Three soil types are considered with shear wave velocities of 70, 100 and 250 m/s. Soil-foundation stiffness is included with a set of springs on the base (impedance functions). Capacity curves of the building are computed with pushover analysis. In addition, non linear time history analysis are used to asses the ductility demands. Results show that ductility capacity of the soil-structure system including rigid body components is reduced. Base flexibility does not modify neither yield and maximum base shear. Equivalent ductility estimated with the proposed equations is fits better the results of the numerical model than the one considering elastoplastic behavior. Modification of beams ductility demand due to base flexibility are not constant within the structure. Some elements experience reduced ductility demands while other elements experience increments when flexible base is considered. Soil structure interaction produces changes in the relation between yield strength reduction factor and structure ductility demand. These changes are dependent on the spectral shape and the period of the system with fixed and flexible base.

• 동력기계공학회지
• /
• 제16권5호
• /
• pp.76-82
• /
• 2012

Duplex stainless steels have the dual microstructure of austenite and ferrite phases. This steel exhibits generally a high corrosion resistance and higher mechanical strength compared with austenitic stainless steels. The steels used in the investigation have the chemical composition of Fe-22Cr-xNi-yMn-0.2N in which the contents of Ni and Mn were varied with maintaining the equal [Ni/Cr] equivalent. The fraction of ferrite phase was increased with the increase of annealing temperature. The impact factor of Mn element on the [Ni] equivalent was amended on the basis of the results of the investigation. 4Mn-2Ni alloy showed the highest pitting corrosion resistance. The fraction ratio, grain size and misorientation angle between grains were measured, and the correlation with pitting potential was investigated.

• Earthquakes and Structures
• /
• 제22권6호
• /
• pp.585-595
• /
• 2022

Using the nonlinear static procedures has become very common in seismic codes to achieve the nonlinear response of the structure during an earthquake. The capacity spectrum method (CSM) adopted in ATC-40 is considered as one of the most known and useful procedures. For this procedure the seismic demand can be approximated from the maximum deformation of an equivalent linear elastic Single-Degree-of-Freedom system (SDOF) that has an equivalent damping ratio and period by using an iterative procedure. Data from the results of this procedure are plotted in acceleration- displacement response spectrum (ADRS) format. Different improvements have been made in order to have more accurate results compared to the Non Linear Time History Analysis (NL-THA). A new procedure is presented in this paper where the iteration process shall not be required. This will be done by estimation the ductility demand response spectrum (DDRS) and the corresponding effective damping of the bilinear system based on a new parameter of control, called normalized yield strength coefficient (η), while retaining the attraction of graphical implementation of the improved procedure of the FEMA-440. The proposed procedure accuracy should be verified with the NL-THA analysis results as a first implementation. The comparison shows that the new procedure provided a good estimation of the nonlinear response of the structure compared with those obtained when using the NL-THA analysis.

• 대한토목학회논문집
• /
• 제38권1호
• /
• pp.19-28
• /
• 2018

거푸집의 탈형 시기는 콘크리트 구조물의 품질과 공사기간, 공사비에 영향을 주는 직접적인 요인으로 콘크리트 구조물의 안전성과 경제성을 확보하는데 중요한 요소이다. 국내 규정에서 거푸집 존치에 대한 규정을 제시하고 있으나 조기에 거푸집을 해체하여 콘크리트의 품질이 저하되고 있다. 이는 양생조건에 대한 이해가 부족하고 공사기간이 단축되길 원하기 때문이다. 따라서 본 연구에서는 콘크리트의 거푸집 탈형시기에 따른 양생조건이 압축강도에 미치는 영향을 시험을 통하여 평가하였다. 연구 결과 거푸집의 12시간 후 조기 탈형은 콘크리트의 28일 압축강도를 최대 약 40% 정도까지 저하시켰으며, 거푸집을 28일 동안 장기간 존치할 경우에는 28일 표준압축강도 대비 약 7%의 강도저하를 가져왔다. 결론으로 본 논문에서는 양생온도를 등가재령으로 고려하여 거푸집 해체 시기에 따른 콘크리트의 압축강도 추정식을 제안하였다. 이 제안식은 현장에서 거푸집 제거 후의 콘크리트 압축강도 평가에 활용될 수 있다.

• Earthquakes and Structures
• /
• 제11권3호
• /
• pp.461-481
• /
• 2016

The research described in this paper investigates the seismic behaviour of lightly reinforced concrete (RC) bearing sandwich panels, heavily conditioned by shear deformation. A numerical model has been prepared, within an open source finite element (FE) platform, to simulate the experimental response of this emerging structural system, whose squat-type geometry affects performance and failure mode. Calibration of this equivalent mechanical model, consisting of a group of regularly spaced vertical elements in combination with a layer of nonlinear springs, which represent the cyclic behaviour of concrete and steel, has been conducted by means of a series of pseudo-static cyclic tests performed on single full-scale prototypes with or without openings. Both cantilevered and fixed-end shear walls have been analyzed. After validation, this numerical procedure, including cyclic-related mechanisms, such as buckling and subsequent slippage of reinforcing re-bars, as well as concrete crushing at the base of the wall, has been used to assess the capacity of two- and three-dimensional low- to mid-rise box-type buildings and, hence, to estimate their strength reduction factors, on the basis of conventional pushover analyses.

• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.654-661
• /
• 2001

In this study, fatigue growth behavior of the transverse crack, which was the most dangerous damage among the various types of rail defects, was investigated using the notched keyhole specimen under constant amplitude loadings. Fatigue limit of smooth specimen in rail steel at R=0 was 110MPa, and the fatigue crack initiation life in the region of the low stress amplitude (ie. long life) occupied the major portion of the total fatigue life. The fatigue strength under variable amplitude loading was converted to the equivalent fatigue strength based upon. Miners rule, which was estimated approximately 9% lower than that under constant amplitude loading. Also, in the low ΔK(sub)rms region ($\leq$21MPa√m), fatigue crack growth rate (da/dN) under constant amplitude loading was higher than that under variable amplitude loading, whereas the tendency was reversed in the high ΔK(sub)rms region. It is believed that this behavior is due to the transition of fracture appearance.