• 한국기계가공학회지
• /
• 제17권2호
• /
• pp.54-59
• /
• 2018

In this study, the durability due to the fork shape of excavator bucket is investigated. The analysis is carried out by modelling the fork shape used in general. As the analysis condition, the pin is constrained as fixed support at the bucket and the load of 12000N is applied at the fork. As the study result, the maximum equivalent stresses at models 1 and 2 are shown as 56.895MPa and 54.722MPa respectively. Model 1 is shown to have the most deformation of 5.6686 mm among four models. Model 3 has the least deformation among four models and the maximum deformation of model 3 is shown as 4.948mm. The fatigue analyses are also carried out with three models. Each model shows the same fatigue lives under the identical fatigue loads. The damage part at each model is shown at the bucket pork or the pin connected with bucket. As this study result, the data is thought to contribute to the safety design at excavator bucket.

• 한국기계가공학회지
• /
• 제12권5호
• /
• pp.57-66
• /
• 2013

This study investigates structural and vibration analyses due to the change of bolt Numbers on models 1 and 2 of flange couplings connected with both sides of axis. As maximum equivalent stresses of models 1 and 2 are 122.05 and 102.3 MPa respectively by the basis of bolt, these stresses are within the allowable stress of this model and the safety of bolt design is verified. As maximum equivalent stresses of models 1 and 2 are 196.2 and 196.4 MPa respectively by the basis of body, these stresses are within the allowable stress of this model and the safety of body design is verified. Through natural frequency analysis, maximum displacements of model 1 and 2 are shown at the frequencies of 6565.1 and 6614.9 Hz respectively. Maximum displacements in cases of models 1 and 2 are shown at harmonic frequencies of 7760 and 7840 Hz at real loading conditions. By putting these study results together, the durability of vibration at model 2 with bolt numbers of 8 becomes better than model 1 with bolt numbers of 6. These study results can be effectively utilized with the design on flange coupling by anticipating and investigating prevention and durability against its damage.

• Journal of Welding and Joining
• /
• 제29권2호
• /
• pp.94-101
• /
• 2011

A lumped mass damped vibratory model was proposed for quantitative understanding of welding machine characteristics. An experimental setup was developed to determine the mechanical parameters (moving mass m, equivalent stiffness k and damping c) which govern the dynamic mechanical response of the resistance spot welding machine. During the test, acceleration of the electrodes for each level of applied load was measured by accelerometer, filtered and numerically integrated to find the corresponding velocity and displacement. The machine dynamic parameters were determined by finding the unknowns of the proposed model with experimental data. A Simulink model was proposed to investigate the influence of these mechanical parameters on the welding process. The electrode response was simulated by changing values of stiffness and damping. It was observed that both of the machine parameters(c, k) have significant effect on the response of electrode head.

• Journal of Welding and Joining
• /
• 제34권5호
• /
• pp.1-5
• /
• 2016

The hardness of laser weldments has been predicted by using several carbon equivalent equations and estimation models. In this study, authors extended the model to boron steel sheets which are adopted for the hot press forming process. four kinds of boron steels with the strengths from 1500 MPa to 1900 MPa were considered and the hardness profiles of weldments was measured from the experiments of this study and the references. The traditional "Kaizu" equation could predict the hardness with an accuracy of -4.9% error although the Kaizu equation does not consider the boron content. Modified carbon equivalents were suggested by adding a term as like 5B or 14B into the Kaizu equation, and it could improve the accuracy of the prediction model.

• 대한기계학회논문집A
• /
• 제36권7호
• /
• pp.731-738
• /
• 2012

본 논문은 상용 유한요소코드인 ANSYS Workbench 12.1과 CFX 12.1을 이용하여 NREL Phase VI Rotor에 대한 공력특성을 입구풍속 7m/s 경우에 대해 연구하였다. 공탄성 효과를 고려하기 위해 약결합 양방향 유체구조 연성기법을 사용하여 타워구조를 제외한 로터파트에 대해서 해석이 수행되었다. 블레이드 끝단의 초기 피치각은 $3^{\circ}$로 설정하였고, 구조해석모델은 등가강성기법을 적용하였다. 신뢰성 있는 수렴판정 결과의 확보를 위해 블레이드 루터부의 굽힘모멘트를 실시간으로 모니터링 하였다. 해석의 신뢰성을 검증하기 위하여 해석결과를 NREL/NASA Ames 풍동 실험결과와 비교 분석하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.432-437
• /
• 2000

The purpose of this paper is to determine a two dimensional axisymmetric model through a comparative study between a three dimensional and an axisymmetric finite element analysis of the reactor coolant piping nozzle subject to internal pressure. The finite element analysis results show that the stress adopting the axisymmetric model with the radius of equivalent spherical vessel are well agree with that adopting the three dimensional model. The the radii of equivalent spherical vessel are 3.5 times and 7.3 times of the radius of the reactor coolant piping for the safety injection nozzle and for the residual heat removal nozzle, respectively.

• 대한기계학회논문집A
• /
• 제33권11호
• /
• pp.1187-1194
• /
• 2009

During the last decade, possibility of flaw occurrences has been rapidly increased world-widely as the increase of operating times of petro-chemical facilities. For instance, from a recent in-service inspection, three different sized surface cracks were detected in welding parts of a spherical oxygen holder in Korea. While API579 code provides corresponding engineering assessment procedures to determine crack driving forces, in the present work, numerical analyses are carried out for the cracked oxygen holder to investigate effects of complex geometry, analysis model and residual stress. With regard to the detailed finite element analysis, stress intensity factors are determined from both the full three-dimensional model and equivalent plate model. Also, as an alternative, stress intensity factors are calculated for equivalent plate model by employing the noted influence stress function technique. Finally, parametric structural integrity evaluation of the cracked oxygen holder is conducted in use of failure assessment diagram method, J/T method and DPFAD method. Effects of the geometry and so forth are examined and key findings from the simulations are fully discussed, which enables to determine practical safety margins of spherical components containing a defect.

• Steel and Composite Structures
• /
• 제47권2호
• /
• pp.289-296
• /
• 2023

The failure of a thin-walled tube was studied in this paper based on three failure models. Both proportional and non-proportional loading paths were applied. Proportional loading consisted of combined tension-torsion. Cyclic non-proportional loading was also applied. It was a circular out-of-phase axial-shear stress loading path. The third loading path was a combination of a constant internal pressure and a bending moment. The failure models under study were equivalent plastic strain, modified Mohr-Coulomb (Bai-Wierzbicki) and Tearing parameter models. The elasto-plastic analysis was conducted using J2 criterion and nonlinear kinematic hardening. The return mapping algorithm was employed to numerically solve the plastic flow relations. The effects of the hydrostatic stress on the plastic flow and the stress triaxiality parameter on the failure were discussed. Each failure model under study was utilized to predict failure. The failure loads obtained from each model were compared with each other. The equivalent plastic strain model was independent from the stress triaxiality parameter, and it predicted the highest failure load in the bending problem. The modified Mohr-Coulomb failure model predicted the lowest failure load for the range of the stress triaxiality parameter and Lode's angle.

• Computers and Concrete
• /
• 제12권1호
• /
• pp.53-64
• /
• 2013

The curing temperature is known to influence the rate of mechanical properties development of early age concrete. In realistic sites the temperature of concrete is not isothermal $20^{\circ}C$, so the paper measured adiabatic temperature increases of four different concretes to understand heat emission during hydration at early age. The temperature-matching curing schedule in accordance with adiabatic temperature increase is adopted to simulate the situation in real massive concrete. The specimens under temperature-matching curing are subjected to realistic temperature for first few days as well as adiabatic condition. The mechanical properties including compressive strength, splitting strength and modulus of elasticity of concretes cured under both temperature-matching curing and isothermal $20^{\circ}C$ curing are investigated. The results denote that comparing temperature-matching curing with isothermal $20^{\circ}C$ curing, the early age concretes mechanical properties are obviously improved, but the later mechanical properties of concretes with pure Portland and containing silica fume are decreased a little and still increased for concretes containing fly ash and slag. On this basement using an equivalent age approach evaluates mechanical properties of early age concrete in real structures, the model parameters are defined by the compressive strength test, and can predict the compressive strength, splitting strength and elasticity modulus through measuring or calculating by finite element method the concreted temperature at early age, and the method is valid, which is applied in a concrete wall for evaluation of crack risking.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3560-3572
• /
• 1996

This paper presents a new discrete-time fuzzy-sliding mode controller for robust vibration control of a smart structure featuring a piezofilm actuator. A governong equation of motion for the smart beam structure is derived and discrete-time codel with mismatched uncertainties such as parameter variations is constructed ina state space. A discrete-time sliding mode control system consisting of an equivalent controller and a discontinuous controller is formulated. In the design of the equivalent part, so called an equivalent controller separation method is adopted to achieve vzster convergence to a sliding surface without extension of a sliding region, in which the system robustness maynot be guaranteed. On the other hand, the discontinuous part is constructed on the basis of both the sliding and the convergence conditions using a time-varying feedback gain. The sliding moide controller is then incorporated with a fuzzy technique to appropriately determine principal control parameters such as a discountinuous feedback gain. Experimental implementation on the forced and random vibraiton controls is undertaken in order to demonstrate superior control performance of the proposed controller.