• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.367-369
• /
• 2008

A theoretical model of equivalent drawbead for sheet metal forming analysis is experimentally verified in this paper. After the theoretical drawbead models improved a material description for the accurate calculation of drawbead forces are briefly introduced, they are verified by showing the good agreement of their drawbead forces with experimental measurements. Furthermore, the excellence of theoretical models is demonstrated by the comparison with those of commercial codes.

• 소성∙가공
• /
• 제18권5호
• /
• pp.371-376
• /
• 2009

An equivalent drawbead model(EDM) for sheet metal forming analysis, which replaces complex drawbead geometries with drawbead forces in modeling the stamping dies with finite elements, is experimentally verified and applied to the numerical simulation of auto-panel stamping process. The drawbead restraining and opening forces of elliptical drawbead, circular drawbead, square drawbead, and step drawbead are obtained by performing the drawbead pulling test and compared with those of EDM and commercial code models(CCM). Better agreement with experimental measurements is found in EDM than CCM. Furthermore, the excellence of EDM is demonstrated in its application to the auto-body stamping analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.389-392
• /
• 2009

The application of an equivalent drawbead model(EDM) for sheet metal forming analysis, which adopts the forces instead of complex geometries in modeling the drawbead, to the numerical simulation of auto-panel stamping process is introduced in this study. In terms of the thinning and draw-in, better agreement with experimental measurements was found in EDM than in commercial code models so that the excellence of EDM in the accuracy of drawbead forces for the simulation of auto-body stampings was revealed.

• 소성∙가공
• /
• 제11권6호
• /
• pp.503-512
• /
• 2002

The drawbead is used to control material flow into the die during the binder wrap process and the stamping process in the sheet metal forming process. Since the dimension of drawbead is relatively small in comparison with the typical dimensions, it is difficult to include drawbeads in finite element analysis of the sheet metal forming process. It is because the mesh system has to be fine enough to describe the drawbead and the computation time is drastically increased. In this paper, simulation of drawbead forming has been carried out to obtain the equivalent boundary conditions in the binder wrap process and the stamping process. In order to investigate the effect of various die geometries, parameter studies are performed with the variation of parameters such as the blank length, the drawbead depth, the drawbead radius, the inclination of die and the friction coefficient.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.420-423
• /
• 2009

In this study, the guideline for designing the drawbeads used in the stamping dies for advanced high strength steel (AHSS) sheets is investigated. In the drawbead drawing test, the drawbead forces for verifying the equivalent drawbead model(EDM) and the sheet strains for finding marginal strains from $FLC_0$ are measured. In the finite element analysis (FEA), the bending allowance, R/t, is obtained. Based on the forming and bending allowances obtained, the design guideline of the drawbead for determining height and width, which depends on the restraining force and the forming allowance, is prepared by using EDM.

• 소성∙가공
• /
• 제11권6호
• /
• pp.513-518
• /
• 2002

The equivalent boundary conditions have been applied to the front door panel forming process, in order to demonstrate its reliability and validity. The elongation in the bead forming process is applied to the binder wrap process as the equivalent displacement boundary condition and the restraining force in the drawing process is applied to stamping process as the equivalent force boundary condition. The result calculated with the equivalent boundary conditions shows closer coincidence with the experimental result than simulation with different boundary conditions. The numerical result fully demonstrates that drawbead forming simulation for calculation of equivalent boundary conditions is necessary and effective.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.266-269
• /
• 2003

This paper is concerned with a forming analysis of front side members and the application of the forming effect in crash analysis of auto-body. Drawbead restraining forces are calculated with ABAQUS/Strandard in order to identify the boundary condition in forming process. Forming analysis with equivalent drawbead is carried out with LS-DYNA3D. In order to demonstrate the validity of the forming analysis, quantitative comparison of the thickness variation between the real product and the numerical simulation result is carried out. Forming histories obtained from the forming analysis are utilized as the initial condition of the crash analysis for accurate assessment of the crashworthiness.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.318-321
• /
• 2005

The shell part is made of 2-layered blank because of functional requirements. To investigate the draw formability in this kind of part, the 2-layered sheet metal forming analysis process should be stipulated. First of all, treatment of contact with each blank must be considered to prevent the penetration on the each blank. Subsequently, applying the draw bead force is considered carefully because application of drawbead force for analysis is different with equivalent drawbead force. Formability as like crack, neck and wrinkles is estimated by FLD(Forming Limit Diagram) and thinning. A feasibility of the 2-layered sheet metal forming analysis process study is verified compare 2-layered sheet metal forming analysis with experimental results.