• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.377-388
• /
• 2022

Laboratory-scale experiments were performed to identify the As removal mechanism of the residual slag generated after the mineral carbonation process. The residual slags were manufactured from the steelmaking slag (blast oxygen furnace slag: BOF) through direct and indirect carbonation process. RDBOF (residual BOF after the direct carbonation) and RIBOF (residual BOF after the indirect carbonation) showed different physicochemical-structural characteristics compared with raw BOF such as chemical-mineralogical properties, the pH level of leachate and forming micropores on the surface of the slag. In batch experiment, 0.1 g of residual slag was added to 10 mL of As-solution (initial concentration: 203.6 mg/L) titrated at various pH levels. The RDBOF showed 99.3% of As removal efficiency at initial pH 1, while it sharply decreased with the increase of initial pH. As the initial pH of solution decreased, the dissolution of carbonate minerals covering the surface was accelerated, increasing the exposed area of Fe-oxide and promoting the adsorption of As-oxyanions on the RDBOF surface. Whereas, the As removal efficiency of RIBOF increased with the increase of initial pH levels, and it reached up to 70% at initial pH 10. Considering the PZC (point of zero charge) of the RIBOF (pH 4.5), it was hardly expected that the electrical adsorption of As-oxyanion on surface of the RIBOF at initial pH of 4-10. Nevertheless it was observed that As-oxyanion was linked to the Fe-oxide on the RIBOF surface by the cation bridge effect of divalent cations such as Ca²⁺, Mn²⁺, and Fe²⁺. The surface of RIBOF became stronger negatively charged, the cation bridge effect was more strictly enforced, and more As can be fixed on the RIBOF surface. However, the Ca-products start to precipitate on the surface at pH 10-11 or higher and they even prevent the surface adsorption of As-oxyanion by Fe-oxide. The TCLP test was performed to evaluate the stability of As fixed on the surface of the residual slag after the batch experiment. Results supported that RDBOF and RIBOF firmly fixed As over the wide pH levels, by considering their As desorption rate of less than 2%. From the results of this study, it was proved that both residual slags can be used as an eco-friendly and low-cost As remover with high As removal efficiency and high stability and they also overcome the pH increase in solution, which is the disadvantage of existing steelmaking slag as an As remover.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.3
• /
• pp.47-56
• /
• 2020

In this study, three levels of W/B(Water to Binder) ratio (0.37, 0.42, 0.47) and substitution ratio of GGBFS (Ground Granulated Blast Furnace Slag) rate (0 %, 30 %, 50 %) were considered to perform RCPT (Rapid Chloride Diffusion Test) at the 1,095 aged day. Accelerated chloride diffusion coefficient and passed charge of each concrete mixture were assessed according to Tang's method and ASTM C 1202, and improving behaviors of durability performance with increasing aged days are analyzed based on the test results of previous aged days from the preceding study. As the age of concrete increases, the passed charge and diffusion coefficient have been significantly reduced, and especially the concrete specimens containing GGBFS showed a significantly more reduction than OPC(Ordinary Portland Cement) concrete specimen by latent hydraulic activity. In the case of OPC concrete's results of passed charge, at the 1,095 days, two of them were still in the "Moderate" class. So, if only OPC is used as the binder of concrete, the resistance performance for chloride attack is weak. In this study, the time-parameters (m) were derived based on the results of the accelerated chloride diffusion coefficient, and the deterministic and probabilistic analysis for service life were performed by assuming the design variable as a probability function. For probabilistic service life analysis, durability failure probabilities were calculated using Monte Carlo Simulation (MCS) to evaluate service life. The service life of probabilistic method were lower than that of deterministic method, since the target value of PDF (Probability of Durability Failure) was set very low at 10 %. If the target value of PDF suitable for the purpose of using structure can be set and proper variability can be considered for each design variable, it is believed that more economical durability design can be made.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.7
• /
• pp.704-712
• /
• 2006

This research was designed to investigate the removal of heavy metals, such as $Al^{3+}$, $Cu^{2+}$, $Mn^{2+}$, $Pb^{2+}$ and $Zn^{2+}$, by adsorption on clay minerals. Bentonite(Raw-Bentonite), $Ca^{2+}$ and $Na^+$ ion exchanged bentonite(Ca- and Na-Bentonite) and montmorillonite, such as KSF and K10 from Sigma Aldrich, were used as adsorbents. The component of five inorganic adsorbents was analyzed by XRF, and the concentration of metal ions was measured by ICP. The cation exchange capacity(CEC) and the particle charge of adsorbents were measured. The initial concentration range of metal ions was $10{\sim}100$ mg/L. From the experimental results, it was shown that the adsorption equilibrium was attained after $1{\sim}2$ hours. The maximum percentage removal of $Al^{3+}$, $Cu^{2+}$, $Pb^{2+}$ and $Zn^{2+}$ on Na-Bentonite were more than 98% and that of $Mn^{2+}$ was 66%. $Al^{3+}$ was leached out from KSF with the higher concentration of hydrogen ion. Percentage removals of $Pb^{2+}$ and $Zn^{2+}$ on KSF were 88% and 59%, respectively. In general, the percentage removal of metal ions was decreased with the higher initial concentration of metal ions. The adsorption capacity of metal ions on Na-Bentonite was $1.3{\sim}19$ mg/g. Freundlich equation was used to fit the acquired experimental data. As the results, the adsorption capacity of metal ions was in the order of Na-Bentonite$\gg$Raw-Bentonite$\cong$K10>Ca-Bentonite>KSF. Freundlich constant, K of Na-Bentonite was the largest for metal ions. The order K of Na-Bentonite was Al>Cu>Pb>Zn>Mn, and the adsorption intensity(1/n) was determined to be $0.2{\sim}0.39$.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.3
• /
• pp.203-207
• /
• 2009

The concern of seriousness and harmful effects of environmental pollution is rising by the various water pollutions, appearances of new micro-noxious substances and increase of sustainable pollutants. The method is suggested that can effectively increase the removal of organic substances and several pollutants using a coagulation process. The experiment for characteristics of $ZrSiO_4$ (zirconium silicate) as a coagulation-aid was carried out for application to coagulation process with domestic wastewater and lake water, and the removal rate of the organic substances depending on a dosage was evaluated by PDA (Photometric Dispersion Analyzer) in this study. Zeta-potential of zirconium silicate solution was -32.22 mv at pH 7 and the lower negative(-) charge was detected in the more acidic conditions. Absorbance on $UV_{254}$ presented higher when zirconium silicate was added than in a domestic wastewater itself. Besides, the results by PDA experiment represented that injection of zirconium silicate could promote growing of floc. Tests for coagulation process were conducted by three ways which are pre-injection, co-injection and post-injection of zirconium silicate with alum. Accordingly, removal efficiency of organic substances increased over 15% in co-injection than in using of alum as a sole reagent. When a 20 mg/L of alum was used with a 10 mg/L of zirconium silicate, the removal efficiency was high up to 90%. Removal efficiency of $COD_{Cr}$ was improved more than 15% in case of dosage of coagulant either PAC (Poly aluminium chloride) or PACS (Poly aluminium chloride Silicate) together with zirconium silicate. As a result, the removal efficiency of $COD_{Cr}$ were 5~10% higher in a co-injection of zirconium silicate with a coagulant than a pre-injection and a post-injection but it of soluble substances was lower in a co-injection.

• Economic and Environmental Geology
• /
• v.54 no.6
• /
• pp.689-698
• /
• 2021

Since the mine reclamation scheme was implemented from 2007 in Korea, various remediation programs have been decontaminated the pollution associated with mining and 254 mines were managed to reclamation from 2011 to 2015. However, as the total amount of contaminated mine drainage has been increased due to the discovery of potential hazards and contaminated zone, more efficient and economical treatment technology is required. Therefore, in this study, the adsorption properties of arsenic was evaluated according to the adsorbents which were derived from water treatment sludge(Alum based adsorbent, ABA-500) and granular ferric hydroxide(GFH), already commercialized. The alum sludge and GFH adsorbents consisted of aluminum, silica materials and amorphous iron hydroxide, respectively. The point of zero charge of ABA-500 and GFH were 5.27 and 6.72, respectively. The result of the analysis of BET revealed that the specific surface area of GFH(257 m²·g^-1) was larger than ABA-500(126~136 m²·g^-1) and all the adsorbents were mesoporous materials inferred from N₂ adsorption-desorption isotherm. The adsorption capacity of adsorbents was compared with the batch experiments that were performed at different reaction times, pH, temperature and initial concentrations of arsenic. As a result of kinetic study, it was confirmed that arsenic was adsorbed rapidly in the order of GFH, ABA-500(granule) and ABA-500(3mm). The adsorption kinetics were fitted to the pseudo-second-order kinetic model for all three adsorbents. The amount of adsorbed arsenic was increased with low pH and high temperature regardless of adsorbents. When the adsorbents reacted at different initial concentrations of arsenic in an hour, ABA-500(granule) and GFH could remove the arsenic below the standard of drinking water if the concentration was below 0.2 mg·g^-1 and 1 mg·g^-1, respectively. The results suggested that the ABA-500(granule), a low-cost adsorbent, had the potential to field application at low contaminated mine drainage.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.455-462
• /
• 2000

The objective of this study was to examine the physicochemical characteristics of coagulation reaction between loess and red tide organisms (RTO) and its feasibility, in developing a technology for the removal of RTO bloom in coastal sea. The physicochemical characteristics of loess were examined for a particle size distribution, surface characteristics by scanning electron microscope, zeta potential, and alkalinity and pH variations in sea water. Two kinds of RTO that were used in this study, Cylindrothen closterium and Skeietonema costatum, were sampled in Masan bay and were cultured in laboratory. Coagulation experiments were conducted using various concentrations of loess, RTO, and a jar tester. The supernatant and RTO culture solution were analyzed for pH, alkalinity, RTO cell number. A negative zeta potential of loess increased with increasing pH at $10^(-3)M$ NaCl solution and had -71.3 mV at pH 9.36. Loess had a positive zeta potential of +1,8 mV at pH 1.98, which resulted in a characteristic of material having an amphoteric surface charge. In NaCl and $CaCl_2$, solutions, loess had a decreasing negative zeta potential with increasing $Na^+\;and\;Ca^(+2)$ ion concentration and then didn't result in a charge reversal due to not occurring specific adsorption for $Na^+$ ion while resulted in a charge reversal due to occurring specific adsorption for $Ca^(+2)$ ion. In sea water, loess and RTO showed the similar zeta potential values of -112,1 and -9.2 mV, respectively and sea sand powder showed the highest zeta potential value of -25.7 mV in the clays. EDLs (electrical double-layers) of loess and RTO were extremely compressed due to high concentration of salts included in sea water, As a result, there didn't almost exist EDL repulsive force between loess and RTO approaching each other and then LVDW (London-yan der Waals) attractive force was always larger than EDL repulsive force to easily form a floe. Removal rates of RTO exponentially increased with increasing a loess concentration. The removal rates steeply increased until $800 mg/l$ of loess, and reached $100{\%}$ at 6,400 mg/l of loess. Removal rates of RTO exponentially increased with increasing a G-value. This indicated that mixing (i.e., collision among particles) was very important for a coagulation reaction. Loess showed the highest RTO removal rates in the clays.

• Journal of the Korean Dietetic Association
• /
• v.11 no.2
• /
• pp.170-178
• /
• 2005

The purposes of this study were 1) to analyze the effect of the information quality of standard menu system of ERP on the user’s satisfaction 2) to analyze the effect of the information quality of standard menu system of ERP on the user’s performance. The questionnaires were distributed to 260 end users(dietitians, foodservice management managers) in charge of managing the institutional foodservice such as the office(government agencies, factories), schools(universities, middle and high school) and hospitals which were managed by contract foodservice management company “C” in Seoul and Kyunggi. The surveys were performed from July 26 to July 30, 2004. Two hundred and fifty questionnaires were responded(response rate : 96.2%). The statistical analysis was conducted by using SPSS Win(11.5). And the descriptive analysis, factor analysis, reliability test, pearson correlation and simple regression analysis were performed. The results showed that the information quality of standard menu system of ERP have a significant positive effect on the user’s satisfaction(p<0.001) and user’s performance(p<0.001). When constructing standard menu system on ERP in the contract foodservice management company, the information quality of standard menu system of ERP should be guaranteed in order to satisfy the end-user and to improve the user’s performance.

• Journal of the Korean Society for Library and Information Science
• /
• v.48 no.2
• /
• pp.89-107
• /
• 2014

The purposes of this study are to analyze the effectiveness of public library reading programs for children in qualitative way and to apply the outcomes to identify areas to measure the success of library reading programs. Interviews were conducted with children who participated in '2013 Reading Books with Libraries' program and adults who were in charge of managing the program. Observations on the program were also conducted. The findings indicate that children who participated in '2013 Reading Books with Libraries' program positively changed in various aspects. Selected areas to measure the success of library reading programs include: reading behavior; attitude to books; awareness of libraries and librarians; participation of library reading programs; the ability to read aloud; the ability to comprehend stories by listening; aggression; the ability to express one's own feelings; speech ability; concentration power; and undiscovered potential. The elements that affect the success or failure of library reading programs include: librarian's enthusiasm on running the reading program; environmental condition of the community child care center; age differences between child participants; running style of the instructor's program; selection of books; child participants' reading abilities and interests in reading; available time for free voluntary reading.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2563-2573
• /
• 2013

Specialty contractors are in charge of the actual construction work and managing many work force in construction sites. The effective educational program for specialty contractors' employees is essential to improve the competitiveness of construction industry. However, there is no in-depth research on training programs for their management or technical staff. Therefore, this study proposes a framework of educational program for the specialty contractors' employees in order to enhance their competence. An extended review of literature related the educational program was carried out to understand the concept, structure, and element of the education system. A questionnaire survey for specialty contractors' employees was performed to investigate the status and problems of educational programs as well as the their educational needs. Based on the survey, the demand-oriented education programs is required to meet the needs of specialty contractors' employees. The framework of demand-oriented education programs for specialty contractors' employees consists of training contents, training type and method, training hour.

• Journal of Forest and Environmental Science
• /
• v.35 no.4
• /
• pp.281-284
• /
• 2019

Efficient management of road-kill data is difficult at national scale when there are many organizations that are in charge of different road types. Here, we described the first case to integrate road-kill data through Korea Road-kill Observation System (KROS) by the Korean government. The system was launched in June 2018 to approximately 3,000 road menders. During 15 months, 5,812 road-kill observations were registered on KROS including mammals, birds, reptiles and amphibians. Of them, about 86 % was occupied by five species (Hydropotes inermis, Felis catus, Capreolus pygargus, Nyctereutes procyonoides, and Canis lupus familiaris) listed in number of occurrences. The observed road-kill frequency rapidly increased until April 2019 and peaked on May 2019. However, as the system is just starting, the results from KROS cannot be treated as the exact representation of road-kill trend in the country. Although the efficient method to manage national road-kill statistic is arranged, still there are some limitations to overcome to make the system stable.