• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.5
• /
• pp.366-372
• /
• 2013

Korean lunar explorer will be launched by korean launcher KSLV-2 in the 2020s in accordance with national space development strategy. Korean lunar explorer is composed of two unmanned orbiter and lander and should be developed as small size and light weight within 550kg of launch mass due to launcher's loading capability. A structure of lunar explorer is required to have sufficient stiffness and strength under launch and operational environment as well as to accommodate mission equipment. This paper describes the result of a preliminary study on structural model design for korean lunar explorer.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.3
• /
• pp.448-457
• /
• 2002

Heat treatment such as quenching of a high-temperature cylinder is being used on steel to produce high strength levels. Especially, the mist cooling with the high and uniform surface heat flux rate s expected to contribute for better products. The experimental mist cooling curve is produced for better understanding, and two distinct heat transfer regions are recognized from the cooling curve produced. It is shown that the liquid film evaporation dominated region follows the film boiling-dominated region as decreasing the temperature of test cylinder by mist flow. Based on the intuitive view from some previous investigations, a simplified model with some assumptions is introduced to explain the mist cooling curve, and it is shown that the estimation agrees well with our experimental data. In the meanwhile, it is known that the wetting temperature, at which surface heat flux rate is a maximum, increases with mass flow rate ratio of water to air ($\varkappa$ < 10). However, based on our experimental data, it is explained that there exists a critical mass flow rate ratio, at which the wetting temperature is maximum, in the range of 3 < $\varkappa$ < 130. Also, it is described that despite of the same value of $\varkappa$, the wetting temperature may increase with mist velocity.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.457-469
• /
• 2012

Bedform data at 4 shallow zones in the Yellow Sea where waves as well as tidal range are high and bed material is relatively coarse were collected and analyzed here. Water depths in the study area where the bedform data were collected are 10 ~ 65 meters, and ripple lengths well developed are between 6 ~ 13 meters. Existing empirical formula for prediction of ripple length as for coexistence of waves and currents include Khelifa and Ouellet(2000) and Soulsby(2005), both of which have been based on laboratory measurements, or field measurements at different physical environment from the Yellow Sea with respect to tidal range, wave strength, and bed material. New scaling factors are proposed here for better prediction of the ripple length on coastal zone in the Yellow Sea.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.3
• /
• pp.143-151
• /
• 2015

The Crack, occurred in the concrete structure, is a major cause of function deterioration such as strength, durability and waterproof. Therefore the need for crack reduction will continue as long as there is concrete structure. But, it is not easy to reduce or prevent crack cause of impact factor of it. There are so many factors of crack such as material, construction and maintenance environment, and structure, and these are acting in combination. So, this study derives a correlation between the cracks and members through reviewing member crack occurred. And member's attribute, related crack, is analyzed by it. It consider that the basic attribute of member is similar when its requirements are similar. Through this study, therefore, foundation of countermeasure of crack will be provided by prediction of crack shape through member's attribute.

• Journal of Korean Society of Forest Science
• /
• v.90 no.3
• /
• pp.388-397
• /
• 2001

In forestry, where improvement of labor environment is quite impossible, improved posture would result in direct effects by preventing waste of physical strength, prevention of accidental injury caused by fatigue accumulated on certain body parts, and prevention of human error by inattentiveness due to weakened body. Therefore, this research carried on analysis of working posture in manual forest work(thinning using chain-saw, salvage cutting using chain-saw, clearing using hand saw, clearance of twiner using sickle, pruning using saw with a long handle, and tending of young growth using sickle) using OWAS analysis system. According to the OWAS method, percentage of OWAS action categories III and IV in the tasks using chain-saw and sickle was higher than another tasks. For the compared middle skillful worker group and low skillful worker group at felling work using chain-saw, percentage of OWAS action categories IV in middle skillful worker group was 5.1%, and low skillful worker group was 14.1%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.758-764
• /
• 2019

The chassis of the Korean light tactical vehicle adopts a frame-on-body structure that uses lightweight design technology in terms of equipment operating characteristics. Military vehicles are operated in much harsher conditions compared to civilian vehicles, including mountainous terrain, especially steep slopes. Due to this characteristic, frame-welded cracks were found on some military vehicles. Therefore, in this paper, road damage analysis was conducted by identifying various roads including the military unit's road. The result confirmed that the operating environment of some military units' tactical road was much harsher than the endurance road test condition. A solution was derived through defect analysis, design review, and actual vehicle driving test. This study can be used as a reference by suggesting the development direction for the durability test of a new vehicle.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.4
• /
• pp.124-131
• /
• 2017

The purpose of this study is to evaluate the basic performance of cement mortar for repair using alumina cement and nitrite can be cured in low temperature environment. For this purpose, the repair mortar used in the domestic construction site was selected and the experimental evaluation was carried out by adjusting the mixing amount by substituting alumina cement and nitrite for the blending ratio. The experimental test results confirmed that alumina cement and nitrite were replaced with the repair mortar, the initial strength was improved. Also, the chemical resistance was improved, the shrinkage behavior was decreased, and the resistance to freezing and thawing was increased. As a result, applying alumina cement and nitrite at a ratio of 2:1 at 7.5%, the surface condition was maintained for 5 months or longer and it was judged to be excellent in practical use for external structures.

• Environmental Engineering Research
• /
• v.25 no.4
• /
• pp.536-544
• /
• 2020

To address organic dye wastewater, economic and effective adsorbents are required. Here, magnetic biochar from alkali-activated rice straw (AMBC) was successfully synthesized using one-step magnetization and carbonization method. The alkaline activation caused the large specific surface area, high pore volume and abundant oxygen-containing groups of the AMBC, and the magnetization gave the AMBC a certain degree of electropositivity and fast equilibrium characteristics. These characteristics collectively contributed to a relative high adsorption capacity of 53.66 mg g^-1 for this adsorbent towards rhodamine B (RhB). In brief, RhB can spontaneously adsorb onto the heterogeneous surface of the AMBC and reach the equilibrium in 60 min. Although the initial pH, ionic strength and other substances of the solution affected the adsorption performance of the AMBC, it could be easily regenerated and reused with considerable adsorption content. Based on the results, H-bonds, π-π stacking and electrostatic interactions were speculated as the primary mechanisms for RhB adsorption onto the AMBC, which was also demonstrated by the FTIR analysis. With the advantageous features of low cost, easy separation, considerable adsorption capacity and favorable stability and reusability, the AMBC would be a potential adsorbent for removing organic dyes from wastewater.

• Journal of the Society of Disaster Information
• /
• v.10 no.3
• /
• pp.466-480
• /
• 2014

In addition to aging social problem, the problem of older age structure ratio in the fire service organization playing the leading role of the disaster response activities is also expected to be this serious situation. In the case of Seoul fire fighting organization, it is expected that the ratio of over the age 50 reaches 31% or 40% between from 10 to 15 years later from now on, but this will be a serious problem in the fire fighting personnel needing a healthy body and physical strength in the disaster situation unlike the civil servants of general staff. Therefore, the purpose of this study is to take measures that can adapt to a new disaster environment of Increasing proportion of the elderly population by presenting the criteria of age limit of fire fighting field activities to analyze the relevance of the ability to perform on-site activities and age of Seoul fire civil servants, by using three analysis criteria.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.23-27
• /
• 2019

People's interest in the environmental problems of the Earth is growing as they come to the modern world, and research is being actively conducted on how to protect the environment. As a result, the automobile industry, one of the causes of environmental pollution, is also affected. Therefore, research is being conducted to improve the fuel economy and light weight of cars, development of pollution-free cars such as electric cars, and aluminium materials that are lighter than ordinary steel sheets and easier to recycle are gaining attention. In this experiment, the material was formed to form a form of aluminium and the material reduction rate of the side wall of the foam was tested according to the amount of side wall. The material used in the experiment was A3003-O, which is less plastic than normal steel plates, but has excellent corrosion resistance, plasticity and weldability compared to aluminium materials, but has poor tensile strength. For tensile testing, a certain array of Forming Shapes was molded and the height of the Forming was set to 5mm, and the height of the Forming was 4.7mm, indicating that the difference between the first 5mm Forming and the height was not large. In addition, the material reduction rate was tested by giving 15, 0, and -0.15 teas, respectively, and was found to be valuable as a product only for -0.15.