• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.1
• /
• pp.17-26
• /
• 2014

This paper presents a dynamic crack propagation algorithm based on the Moving Least Squares(MLS) difference method. The derivative approximation for the MLS difference method is derived by Taylor expansion and moving least squares procedure. The method can analyze dynamic crack problems using only node model, which is completely free from the constraint of grid or mesh structure. The dynamic equilibrium equation is integrated by the Newmark method. When a crack propagates, the MLS difference method does not need the reconstruction of mode model at every time step, instead, partial revision of nodal arrangement near the new crack tip is carried out. A crack is modeled by the visibility criterion and dynamic energy release rate is evaluated to decide the onset of crack growth together with the corresponding growth angle. Mode I and mixed mode crack propagation problems are numerically simulated and the accuracy and stability of the proposed algorithm are successfully verified through the comparison with the analytical solutions and the Element-Free Galerkin method results.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.161-167
• /
• 2014

This paper describes reinforcement method of reinforced earth wall near the abutment. The excessive displacement of a case affected by reduction of bearing capacity due to macro-environment condition like a coast. That is, the front displacement of reinforced earth wall has been happening continuously due to strength reduction of foundation ground. The micro pile is applied to reinforcement method, in order to secure a bearing capacity and global slope stability of reinforced earth wall. The results of numerical analysis confirmed that reinforcement method based on micro pile can secure a stability of structure, while the reconstruction of reinforced earth wall is impossible by construction and macro-environment condition.

• Journal of The Geomorphological Association of Korea
• /
• v.24 no.2
• /
• pp.65-78
• /
• 2017

In this study, stable carbon isotopic analysis (22 specimens) and magnetic susceptibility analysis (23 specimens) were conducted out on the specimens collected from two points (trench DT1, DT2) in the floodplain of Jemincheon(hereinafter the Jemin plain) to reconstruct the Holocene Environments (Period I, Period II, Period III) of the Jemin plain in Gongju, Chungnam. The results were as follows: In Period I (approximately 7,480~4,940 yrs B.P.) and especially around 7,480~7,320 yrs B.P., it was cool-dry and there were two minor climate fluctuations. This period received a continuous flow of sediments, rather than massive amounts of sediments due to abrupt flooding, and therefore, there was almost no soilization process. Period II(approximately 4,940~2,600 yrs B.P.) was also relatively cool-dry. However, in Period II b, unlike I, the minor climate fluctuations were less pronounced. In this period, flooding and desiccation repeated, inducing soilization processes especially around 3,160 yrs B.P. In Stage III (~360 yrs B.P.), it was warm and humid compared to II b. However, in III a, there was no inflow of sediments due to irregular flooding, and in fact, soilization process was more manifested than during II b due to the impact of the desiccation environment. However, there were some mass movements from Bonghwang Mt. (a.s.l. 147m) caused by heavy rains and typhoon during III b (approximately 360 yrs B.P.), thus moving a large amount of debris (i.e. gravel), which resulted in sedimentation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.10
• /
• pp.1416-1426
• /
• 2021

In the case of a scanning type multi-channel LiDAR sensor, the distance error called a walk error may occur due to a difference in received signal power. This work error causes different distance values to be output for the same object when scanning the surrounding environment based on multiple LiDAR sensors. For minimizing walk error in overlapping regions when scanning all directions using multiple sensors, to calibrate distance for each channels using convolution on external system. Four sensors were placed in the center of 6×6 m environment and scanned around. As a result of applying the proposed filtering method, the distance error could be improved by about 68% from average of 0.5125 m to 0.16 m, and the standard deviation could be improved by about 48% from average of 0.0591 to 0.030675.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.8
• /
• pp.1039-1045
• /
• 2021

In modern society, due to the influence of the 4th industrial revolution, camera sensors and image-based automation systems are being used in various fields, and interest in image and signal processing is increasing. In this paper, we propose a digital filter algorithm for image reconstruction in an impulse noise environment. The proposed algorithm divides the image into eight masks in vertical, horizontal, and diagonal directions based on the local mask set in the image, and compares the standard deviation of each segmentation mask to obtain a reference value. The final output is calculated by applying the weight according to the spatial distance and the weight using the reference value to the local mask. To evaluate the performance of the proposed algorithm, it was simulated with the existing algorithm, and the performance was compared using enlarged images and PSNR.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1189-1198
• /
• 2021

When performing remote tasks using robots in nuclear power plants, a 3D shape measurement system is advantageous in improving the efficiency of remote operations by easily identifying the current state of the target object for example, size, shape, and distance information. Nuclear power plants have high-radiation and underwater environments therefore the electronic parts that comprise 3D shape measurement systems are prone to degradation and thus cannot be used for a long period of time. Also, given the refraction caused by a medium change in the underwater environment, optical design constraints and calibration methods for them are required. The present study proposed a method for developing an underwater 3D shape measurement system with improved radiation tolerance, which is composed of commercial electric parts and a stereo camera while being capable of easily and readily correcting underwater refraction. In an effort to improve its radiation tolerance, the number of parts that are exposed to a radiation environment was minimized to include only necessary components, such as a line beam laser, a motor to rotate the line beam laser, and a stereo camera. Given that a signal processing circuit and control circuit of the camera is susceptible to radiation, an image sensor and lens of the camera were separated from its main body to improve radiation tolerance. The prototype developed in the present study was made of commercial electric parts, and thus it was possible to improve the overall radiation tolerance at a relatively low cost. Also, it was easy to manufacture because there are few constraints for optical design.

• Ocean and Polar Research
• /
• v.45 no.2
• /
• pp.89-102
• /
• 2023

Climate and environmental changes in the Arctic Ocean due to global warming have been linked to extreme climate change in mid-latitude regions, including the Korean Peninsula, requiring a better understanding of the Arctic climate system based on the paleo-analog. This review introduces three paleoenvironmental research cases using neodymium isotopes (¹⁴³Nd/¹⁴⁴Nd, ε_Nd) measured on two different fractions of marine sediments: silicate-bound 'detrital' and Fe-Mn oxide-dominated 'authigenic' fractions. In the first case, detrital ε_Nd in core HH17-1085-GC on the continental shelf off northern Svalbard was used for tracing changes in sediment provenance and associated glacier behavior over the last 16.3 ka. The second case showed the potential use of authigenic ε_Nd as a quasi-conservative water mass tracer. Three prominent ε_Nd peaks and troughs observed in core PS72/410-1 from the Mendeleev Ridge in the western Arctic Ocean over the past 76 ka suggested episodic meltwater discharge events during 51~46, 39~35 and 21~13 ka BP. The last case proposed the use of the difference between authigenic and detrital ε_Nd as a proxy for reconstructing glacier fluctuation. The idea is based on the assumption that enhanced glacial erosion during glacier advances can supply sufficient freshly-exposed rock substrate for incongruent weathering, potentially leading to greater isotopic decoupling between bedrock and dissolved weathering products as recorded in detrital and authigenic ε_Nd, respectively. Thus, it would be worthwhile to take advantage of sedimentary ε_Nd to improve our understanding of past environmental changes in polar regions.

• The Journal of the Korea Contents Association
• /
• v.20 no.4
• /
• pp.273-283
• /
• 2020

The purpose of this study is to evaluate the user's evaluation of the street environment for the Urban Regeneration New Deal project, which maintains its original urban context and improves the urban environment, as opposed to the full-demolition projects such as urban redevelopment or reconstruction. A questionary survey was conducted on residents for the general neighborhood type of Urban Regeneration New Deal projects in Daegu. An IPA(Importance-Performance Analysis) was conducted to compare the user's satisfaction with the street environments. The main results are as follows. First, the importance and satisfaction of street environments were different for each project. Second, the cleanliness of sidewalks showed high importance and satisfaction at all projects. Third, residents' satisfaction with signs and buildings was high, but their importance was low. Last, residents' satisfaction with parking and the segregation of pedestrian and vehicle was low, but their importance was high. It is necessary to build differentiated plans and programs to meet the needs of residents in the Urban Regeneration New Deal projects.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.2
• /
• pp.117-131
• /
• 2007

Representation of building internal space is an active research area as the need for more geometrically accurate and visually realistic increases. 3 dimensional representation is common ground of research for disciplines such as computer graphics, architectural design and engineering and Geographic Information System (GIS). In many cases CAD plans are the starting point of reconstruction of 3D building models. The main objectives of building reconstruction in GIS applications are visualization and spatial analysis. Hence, CAD plans need to be preprocessed and edited to adapt to the data models of GIS SW and then georeferenced to enable spatial analysis. This study automated the preprocessing of CAD data using AutoCAD VBA (Visual Basic Application), and the processed data was topologically restructured for further analysis in GIS environment. Accuracy of georeferencing CAD data was also examined by comparing the results of coordinate transformation by using digital maps and GPS measurements as the sources of ground control points. The reconstructed buildings were then applied to visualization and network modeling.

• Fire Science and Engineering
• /
• v.27 no.2
• /
• pp.25-30
• /
• 2013

'Heaundae Woosin Building' fire was the case that a fire breaking out on the $4^{th}$ floor spread out the $38^{th}$ floor which is a top story and the penthouse was destroyed by fire. After this fire, the fire safety for high rise buildings has been on the rise and several new laws and regulations related in the buildings were created. The study is to analyze Heaundae officetel building case using FDS which is one of the CFD programs for fire. The methodology of this study is to analyze the case comparing with fire spread and route from a virtual fire simulation and related articles and a video clip of actual scene fire. This study shows that a fire spreading on top of levels spent approximately 30 minutes and, which is similar to the actual fire case. Also the pattern of spread has similarity with the case. However, even if the actual fire case shows the fire pattern was "V shape", the smoke-view presents the fire dose not spread horizontally as much as the real fire case. The result shows uncertainty of the modeling based on many grids and a limitation of putting interior finish input sources and the direction of the wind might cause the difference. Also, to analyze factors influencing on a vertical fire, another fire modeling is performed by in condition of modeling environment considering concrete interior finish between buildings and no wind. The result presents the fire spread in smoke-view does not spread vertically as much as the actual case.