• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1421-1432
• /
• 2018

Water soluble oil was obtained from the pyrolysis of coconut waste as a biomass at $600^{\circ}C$. It was studied that the combustion characteristics of bio-emulsion fuel by mixing and emulsifying 15~20% of water soluble oil which obtained from pyrolysis of coconut waste as a biomass and MDO(marine diesel oil) as a marine fuel. Engine dynamometer was used for detecting emissions, temperature, and power. The temperature of combustion chamber was decreased because the moisture in bio-emulsion fuel deprived of heat of evaporation in combustion chamber. While combustion, micro-explosion took place in the combustion chamber by water in the bio-emulsion fuel, MDO fuel scattered to micro particles and it caused to smoke reduction. The temperature reduction of combustion chamber by using bio-emulsion fuel reduced the NOx emission. The increasing of bio-oil content caused increasing water content in bio-emulsion fuel so total calorific value was reduced. So the characteristics of power was decreased in proportion to using the increasing amount of bio-emulsion fuel. Heavy oil as a marine fuel exhausts a lot of smoke and NOx. We expect that we can reduce the exhaust gas of marine engine such as smoke and NOx by using of bio-emulsion fuel as a marine fuel.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.297-300
• /
• 2004

The various microbial tests were performed to determine bioremediation agent capacity for eight strains isolated from the oil contaminated regions. Two tests for isolated strains were conducted such as cell hydrophobicity and emulsifying activity. The biodegradation of SHM (saturated hydrocarbon mixture) and AHM (aromatic hydrocarbon mixture) with the strains also was carried out. The strains having higher cell hydrophobicity and emulsifying activity degraded petroleum oil effectively. The degradation capacity for SHM was represented more than 90% in YS-7 and WLH-1 of isolated strains, and KH3-2 were capable of degrading AHM. Especially, WLH-1 as yeast was shown more than two or three times in the degradation capacity of automobile engine lubricants and the biomonitoring results of contaminated soil for residual oil degrading test showed that the hydrocarbon biodegradation was increased in the second treatment by this strain.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.313-316
• /
• 2012

In this study, the combustion and emission characteristics of waste cooking oil biodiesel was investigated. The fuel was injected from 5 CAD (Crank angle degree) ATDC (After top dead center) to -60 CAD ATDC by 5 CAD with 800 bar and 1600 bar injection pressure. Generally, the hydrocarbon, carbon monoxide and smoke emissions from biodiesel fuel were lower than the emission levels of diesel fuel. However, the emission characteristic of biodiesel got worse than diesel when the fuel was injected earlier than -30 CAD ATDC. $NO_x$ emission from biodeisel was higher than diesel fuel in all experimental conditions.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.05a
• /
• pp.301-304
• /
• 2003

현재 웹이 가지고 있는 문제점들을 해결하기 위해서 연구하고 있는 차세대 웹을 시멘틱 웹이라고 한다. 시멘틱 웹에서 다루고 있는 기술들은 다양하지만 시멘틱 웹 구현에 있어서 온톨로지와 그 온톤로지를 추론하여 agent가 정보의 Semantic을 알아내는 것이 가장 핵심되는 영역의 기술이다. 본 논문에서는 DAML+OIL로 작성된 온톨로지의 추론 방법과 추론 결과물을 이용한 온톨로지 수정방법에 대해서 제안한다. 이를 위해서 온톨로지를 inference engine에서 작업을 수행할 수 있도록 FOL로 변환하는 기술, DAML+OIL axiom과 FOL을 이용해서 inference 할 수 있는 엔진 구축 기술, inference 결과물을 DAML+OIL로 변환하여 수정하는 방법들을 제안한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.1
• /
• pp.26-33
• /
• 2007

The intake swirl motion, as one of dominant effects for an engine combustion. is very effective for turbulence enhancement during the compression process in the cylinder of 2-valve engine. Because the combustion flame speed is determined by the turbulence that is mainly generated from the mean flow of the charge air motion in intake port system. This paper describes the experimental results of swirl flow and combustion characteristics by using the oil spot method and back-scattering Laser Doppler velocimeter (LDV) in 2-valve single cylinder transparent LPG engine using the liquid phase LPG injection. For this. various intake port configurations were developed by using the flow box system and swirl ratios for different intake port configurations were determined by impulse swirl meter in a steady flow rig test. And the effects of intake swirl ratio on combustion characteristics in an LPG engine were analyzed with some analysis parameters that is swirl ratio. mean flow coefficient, swirl mean velocity fuel conversion efficiency. combustion duration and cyclic variations of indicated mean effective pressure(IMEP). As these research results, we found that the intake port configuration with swirl ratio of 2.0 that has a reasonable lean combustion stability is very suitable to an $11{\ell}$ heavy-duty LPG engine with liquid phase fuel injection system. It also has a better mean flow coefficient of 0.34 to develope a stable flame kernel and to produce high performance. This research expects to clarify major factor that effects on the design of intake port efficiently with the optimized swirl ratio for the heavy duty LPG engine.

• Journal of the Korean Institute of Gas
• /
• v.15 no.1
• /
• pp.9-14
• /
• 2011

Heavy duty diesel engine has relatively small portion of whole vehicles due to long drive distance and large engine displacement, but largely influences atmosphere environment. City buses changed to CNG (Compressed Natural Gas) bus with Korea-Japan Worldcup. Heavy duty truck and intercity bus, however, were impossible to use CNG because those kinds of vehicles had long drive distance and CNG station was installed mainly at the around of the bus garage of city. Insulation container storing the natural gas as a liquid makes heavy duty truck and intercity bus possible to use the natural gas. Drive using diesel is possible where is hard to recharge the gas. With LNG (Liquefied Natural Gas), the dependence on oil is largely decreased, PM (Particulate Matter) and NOx which is chronic disadvantage of diesel is remarkably reduced and finally $CO_2$, the representative green house gas, is reduced over 10%.

• Journal of Power System Engineering
• /
• v.6 no.1
• /
• pp.20-26
• /
• 2002

The purpose of this study is preventing the stick, scuffing, scratch between piston and cylinder in advance, and obtaining data for duration test in actual engine operation. The temperature gradient in cylinder bore according to coolant temperature were measured using $1.5{\ell}$ class diesel engine. 20 thermocouples were installed 2mm deep inside from cylinder wall near top ring of piston in cylinder block, at which points major thermal loads exist. It is suggested as proper measurement points for engine design by industrial engineers. Under full load and $70^{\circ}$, $80^{\circ}C$ and $90^{\circ}C$ coolant temperature conditions, the temperature in cylinder block and engine oil increased gradually according to the increase of coolant temperature, the siamese side temperature of top dead center is $142^{\circ}C$ in peripheral distribution, that is about $20^{\circ}C$ higher than that at thrust, anti-thrust, and rear side temperature, respectively. The maximum pressure of combustion gas in $70^{\circ}C$ coolant temperature is about 2 bar lower than those of $80^{\circ}C$ and $90^{\circ}C$ coolant temperature. The engine torque in $80^{\circ}C$, $90^{\circ}C$ coolant temperature condition is about 4.9Nm higher than that of $70^{\circ}C$ coolant temperature.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.25-28
• /
• 2014

In this study, waste cooking oil was gasified in a fluidized bed reactor. The main objective of this study was to produce clean producer gas for power generation engine. As a result, heating value of producer gas is suitable for engine operation and tar content in producer gas was satisfied after use of activated carbon filter. Results from a lab scale experiment and a preliminary results from a pilot scale experiment will be presented.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.4
• /
• pp.181-188
• /
• 2010

The objectives of this study are to analyze the possibility of the landfill gas recycling for the middle and small scale landfills where the recycling facilities are not installed in Korea. It was found that the power generation plants by landfill gas were installed in domestic 15 landfills and the gas engine generation was adopted in 14 places. As the result of economic analysis, the landfill gas recycling is found to be available in 12 places and CERs of 153,693 $tCO_{2e}$ can be secured per year. Through the reduction of the air pollutants and VOCs, the social benefits of 730 million won accrue per year. Also, the power production of 18.8 GWh will substitute the crude oil imports of 4,048 TOE and the revenue of 2.49 billion won is expected to power trading. It is also found that the power generation plants by landfill gas will give the social benefits such as the reduction of the environmental problems and the substitution effect of crude oil imports.

• Journal of Advanced Marine Engineering and Technology
• /
• v.5 no.1
• /
• pp.12-19
• /
• 1981

As the fuel oil cost covers from 45% to 60% of the total expenditure for fishing boat operation, the energy saving is now an urgent problem to be taken a countermeasure for engineers, manufacturers or specialists engaging in this field. Undertaking a second-hand engine of the trainging ship, the author made several reconstructions to restore its performances. By inserting foot linears of connecting rods the compression ratio was increased and by adjusting both the fuel injection timing and the cooling water outlet temperature, its thermal efficiency was improved. The results of the experimental operation were summarized as follows. 1. By raising the piston top position 0.75mm more than the value of the operating manual, the compression pressure increased 1.3 kg/$cm^2$ and the maximum pressure did 3.4 kg/$cm^2$ at 75% load. 2. At 75% load, the difference of the maximum pressure between each cylinder was decreased from 2.4 kg/$cm^2$ to 1.8 kg/$cm^2$. 3. The fuel consumption was decreased about 8 g/ps.h at 75% load, and about 5.3 g/ps.h at 85% load. 4. The brake thermal efficiency was improved about 1.5% at 75% load and 0.9% at 85% load.