• Journal of Korean Society for Atmospheric Environment
• /
• v.2 no.1
• /
• pp.91-101
• /
• 1986

Relations of each factor affected by emissions and the prediction of performance have been analyzed numerically by cycle simulation in the Spark Ignition Engine. Through theoretical analysis and experiments, the results are obtained as below. The calculated results and the experimental ones are almost highly agreeable on cycle simulation model, exhaust gas analysis and efficiency for processes in cylinder. Therefore this model is proved appropriate and can be useful for optimum design of Spark Ignition Engines on parametric studies. It is reaffirmed that the Wiebe's function is suitable for predicting Combustion Ration in Spark Ignition Engines. On parametric studies, it is found that optimum conditions whose density of emissions are lower and efficiency is maximum within propriety value are crankangle ATDC $15^\circ-20^\circ$, 2400 rpm. A/F=16 in this experiment.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.47-61
• /
• 1983

In this paper the simulation of a thermodynamic power cycle for a 4-stroke, single-cylinder, spark-ignition engine was studied. In this simulation the cylinder volume was restricted to two zones, a burnt and an unburnt zone, and the convective heat transfer from cylinder contents to surroundings was considered. The chemical species in burnt gas considered was 12 species including H$_{2}$O, H$_{2}$, OH, H, N$_{2}$, NO, N, CO$_{2}$, CO, $O_{2}$, O and Ar. Using this model, computer program for compression, ignition and expansion processes was composed and pressure, temperature and composition of cylinder gas at each crank angle were computed. The composition of CO$_{2}$, CO, $O_{2}$ in the burnt gas when exhaust valve opens, the maximum temperature, the maximum flame speed and the combustion duration were also computed as a function of equivalence ratio. The relation between burnt mass fraction and burnt volume fraction was also computed.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.7-12
• /
• 2016

In this study, to research in-cylinder flow characteristics of spark-ignited engine with intake valve closing timing change for Miller cycle. 3D simulation study were used 6 different intake valve profile with $CAD10^{\circ}$ gap for retard intake valve closing timing. Comparison of In-cylinder flow pattern characteristic were accompanied between Base and LIVC. And the efficiency of volume and the work of compression were analyzed with simulation study. When intake valve closing angle was retarded in $CAD50^{\circ}$, the pressure in cylinder was decreased about 12~13 bar and volume efficiency was reduced about 16%. The efficiency of volume and the work of compression were reduced on LIVC.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.65-73
• /
• 2008

The purpose of this study is development of universal engine model for integrated Hybrid Electric Vehicle (HEV) simulator and a optimization of engine model. The engine model of this study is based on the MATLAB Simulink for universal and include engine fuel economy technologies for HEV. Various engine fuel economy technologies for HEV is estimated by commercial engine 1-D simulation program - WAVE. And, the 1-D simulation model of base version is compared with engine experiment result. The analyzed engine technologies with 1-D simulation are Dual-CVVT, Atkinson-Cycle and Cylinder-Deactivation System. There are improvement of fuel economy and power performance with Dual-CVVT model at part load and full load, pumping loss reduction with Cylinder-Deactivation System at idle and regeneration. Each estimated technologies are analyzed by 1-D simulation on all operation region for base data to converse simulink. The simulink based engine model maintains a signal with ECU for determination of engine operation point.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.122-129
• /
• 1996

The spark timing is one of major parameters to the engine performance and emissions. The ECU controls the spark timing based on preset values, which are functions of load and speed, in most of today's automotive SI engine. In this system, the preset spark timing can be different from optimum value due to the deviations from mass production, aging effects and so on. In the present study, a control logic is investigated for real time adaptation of spark timing to optimal value. It has been found that crank angle of miximum cylinder pressure is one of the appropriate parameters to estimate the optimum spark timing throught experiment. It has also been observed for spark timing convergence by variation of engineering model factors. The simulation program including engineering model for cycle by cycle variation of combustion is developed for surveying spark timing control logic. It is also shown that simulation results reflect experiment outputs and reasonableness of spark timing control logic for crank angle of maximum cylinder pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.47-52
• /
• 2016

Miller timing is one of the promising ways which can improve the fuel consumption of internal combustion engines. Indeed, Miller timing employing an early intake valve close is widely applied to large diesel and gas engines to enhance performance and reduce NOx emissions. In this study, performance evaluation is carried out by 1-D cycle simulation in order to estimate the effect of Miller CAM timing before BDC for a 32 L turbocharged diesel engine. To optimize Miller CAM timing, a single stage turbocharger is matched with an early intake valve close since boost pressure is a significant parameter that can control compression work in a turbocharged engine. The engine simulation result shows that there is enough potential to improve fuel consumption rate and also reduce NOx emissions at the same time.Abstract here.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.25-38
• /
• 1988

As a mean of increasing engine power, great attention has been concentrated on the turbo-charging owing to better fuel economy, smaller engine size and lower emission. The performance in turbocharged engine depends not only on the efficiency of the engine and the turbocharger used, but also on the total characteristics of the system by the matching turbocharger to the engine. The matching of the turbocharger to the engine has been usually accomplished by the empirical techniques with a great deal of laborious work. It would be better to predict the performance and emission in the turbocharged engine using the effective simulation model. In this study, computer simulation program has been developed to predict the transient variation of properties of gas in the cylinder, intake and exhaust pipes, the engine performances and emissions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.779-783
• /
• 2004

First this paper introduces an advanced FADEC (Full Authority Digital Electric Control) for current and future jet engines.It is designed to realize not only stable thrust control, but also performance improvement, reliability enhancement, service life extension, etc. It can be built by using current micro-processor with high computational power and there exists no difficulties but reliability problem of the micro- processor. Next, the simulation results of SFC minimization control are shown. The target engine is a supersonic, low-bypass ratio, 2-spool, combined cycle turbofan, designated as HYPR90T, which consists of a turbo engine for under Mach 3 flight and a ram engine for over Mach 3 flight. he results can then be used for performance optimization of the engine, which plays important role in the advanced FADEC.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.16-16
• /
• 2000

항공기 가스 터어빈 엔진의 공기 열역학적 특성을 분석하고 예측하기 위한 simulation program이 KARI-ONEP (Korea Aerospace Research Institute -ON-design Engine Program)의 이름으로 개발되었다. 이 program은 on-design cycle analysis를 위한 것으로서 program의 수행에 필요한 엔진 구성요소별 특성 치 data인 input data를 생성하는 input data generator인 KARI-ONEPi와 cycle analysis를 수행하는 주 program인 KARI_ONEPe로 구성이 되어있다.(중략)

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.24-34
• /
• 1985

The study of unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 4-stroke cycle spark ignition engine is presented in this paper. The generalized method of characteristics including friction, heat transfer, change of flow area and entropy gradients was used for solving the equations defining the gas exchange process. The path line calculation was also conducted to allow for calculation of the gas composition and entropy change along the path lines, and of the variable specific heat due to the change of temperature and composition. As the result of the simulation, the properties at each point in the inlet and exhaust pipe, pressure and temperature in the cylinder, and charging efficiency were obtained. Pumping loss and residual gas fraction were also computed. The effect of engine speed, exhaust and inlet pipe length on the pumping loss and charging efficiency were studied showing that the results were in agreement with what has been known from experiments.