• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.531-536
• /
• 1999

Experiments on micro-leak of water were carried out with the water injecting simulator in liquid sodium atmosphere. The leak path was plugged by the sodium-water reaction products in the 2.25Cr-1Mo steel specimen. However, leak paths re-opened in most cases. The self-wastage patterns were not affected by the sodium temperature in the re-opened specimen. The diameter of the defected area, including the re-opened part, was about 5 min. It took 143, 40.7 and 34.7 minutes to re-open the leak path at 450, 475, and $510^{\circ}C$, respectively. It was concluded that the reopening time decreased with the increasing temperature.

• Nuclear Engineering and Technology
• /
• v.47 no.6
• /
• pp.700-711
• /
• 2015

Sodium-cooled fast breeder reactors use liquid sodium as a moderator and coolant to transfer heat from the reactor core. The main hazard associated with sodium is its rapid reaction with water. Sodium-water reaction (SWR) takes place when water or vapor leak into the sodium side through a crack on a heat-transfer tube in a steam generator. If the SWR continues for some time, the SWR will damage the surface of the defective area, causing it to enlarge. This self-enlargement of the crack is called "self-wastage phenomena." A stepwise numerical evaluation model of the self-wastage phenomena was devised using a computational code of multicomponent multiphase flow involving a sodium-water chemical reaction: sodiumwater reaction analysis physics of interdisciplinary multiphase flow (SERAPHIM). The temperature of gas mixture and the concentration of NaOH at the surface of the tube wall are obtained by a numerical calculation using SERAPHIM. Averaged thermophysical properties are used to assess the local wastage depth at the tube surface. By reflecting the wastage depth to the computational grid, the self-wastage phenomena are evaluated. A two-dimensional benchmark analysis of an SWAT (Sodium-Water reAction Test rig) experiment is carried out to evaluate the feasibility of the numerical model. Numerical results show that the geometry and scale of enlarged cracks show good agreement with the experimental result. Enlarged cracks appear to taper inward to a significantly smaller opening on the inside of the tube wall. The enlarged outer diameter of the crack is 4.72 mm, which shows good agreement with the experimental data (4.96 mm).

• Nuclear Engineering and Technology
• /
• v.48 no.2
• /
• pp.368-375
• /
• 2016

A sodiume-water reaction takes place when high-pressured water vapor leaks into sodium through a tiny defect on the surface of the heat transfer tube in a steam generator of the sodium-cooled fast reactor. The sodiume-water reaction brings deterioration of the mechanical strength of the heat transfer tube at the initial leakage site. As a result, it damages the crack itself, which may eventually enlarge into a larger opening. This self-enlargement is called "self-wastage phenomenon." In this study, a simulant experiment was proposed to reproduce the self-enlargement of a crack and to evaluate the mechanism of the self-wastage. The damage on the surface of the crack was simulated by making the neutralization reaction with hydrochloric acid solution and sodium hydroxide solution. A numerical investigation was carried out to validate the feasibility of the approach and to determine experimental conditions. From the computation results, it is observed that when 5M HCl is injected into 5M of NaOH with 0.05 m/s inlet velocity, the temperature at the surface near the crack increased over 319.26 K. The computational results show that the self-wastage phenomenon is capable of being reproduced by the simulant experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1157-1163
• /
• 2008

Fuel represents a significant portion of the operating costs of voyages of the vessel. Under this situation, dramatic increase in fuel price caused a problem that earnings of ship becomes decreased seriously. Pumps in a cooling system of the vessel are often operated inefficiently. The reasons will vary from process to process and application to application. Inefficiency of pumps is one of the reason for making the cost of operating the vessel increased. This paper suggests energy-effective cooling system that controls sea water pumps with inverters to reduce energy consumption in vessel by conducting simulation with LabVIEW. Results shows that electric energy consumption of pumps are significantly deceased. If this energy-effective cooling system is applied to other systems which need cooling, it could be useful in reducing electric energy wastage.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.257-264
• /
• 2024

The sodium cooled fast reactor (SFR) is one of the Gen-IV reactors with the most operating experience accumulated. Although the technology level is the most mature among the Gen-IV reactors, there is still a safety problem that has not been solved, which is the sodium-water reaction. Since sodium and water are separated only by a heat transfer tube with a thickness of only a few mm, there is inherently a risk of a sodium-water reaction (SWR) accident in the SFR. In this study, it is attempted to quantitatively evaluate the resistance of SWR accidents by replacing the shell and tube steam generator with printed circuit steam generator (PCSG) as a method to mitigate the SWR accident. To do this, a CATS-S (Compact Accident Tolerance Steam Generator-SWR) facility was designed and built. And for the quantitative evaluation of accident resistance, a methodology for measuring the impingement wastage rate was established. As a result of this research, the impingement wastage rate caused by SWR generated in a PCSG was measured first time. It was confirmed that the impingement wastage phenomenon was suppressed in the PCSG, and the accident resistance was higher than that of the SWR through comparison with the experimental results performed in the existing shell and tube steam generator. In conclusion, a PCSG is more resistant to impingement wastage as a result of the SWR accident than existing shell and tube steam generators, and it is estimated that a PCSG can mitigate SWR accidents, an inherent problem of SFR.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.863-870
• /
• 2016

We investigated the physical/chemical phenomena that a slow loss of $CO_2$ inventory into sodium after the sodium-$CO_2$ boundary failure in printed circuit heat exchangers (PCHEs), which is considered for the supercritical $CO_2$ Brayton cycle power conversion system of a sodium-cooled fast reactor (SFR). The first phenomenon is plugging inside narrow sodium channels by micro cracks and the other one is damage propagation referred to as wastage combined with the corrosion/erosion effect. Experimental results of plugging shows that sodium flow immediately stopped as $CO_2$ was injected through the nozzle at $300{\sim}400^{\circ}C$ in 3 mmID sodium channels, whereas sodium flow stopped about 60 min after $CO_2$ injection in 5 mmID sodium channels. These results imply that if pressure boundary of sodium-$CO_2$ fails a narrow sodium channel would be plugged by reaction products in a short time whereas a relatively wider sodium channel would be plugged with higher concentration of reaction products. Wastage by the erosion effect of $CO_2$ (200~250 bar) hardly occurred regardless of the kinds of materials (stainless steel 316, Inconel 600, and 9Cr-1Mo steel), temperature ($400{\sim}500^{\circ}C$), or the diameter of the $CO_2$ nozzle (0.2~0.8 mm). Velocities at the $CO_2$ nozzle were specified as Mach 0.4~0.7. Our experimental results are expected to be used for determining the design parameters of PCHEs for their safeties.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10A
• /
• pp.1004-1014
• /
• 2007

In sensor networks, it is crucial to reliably and energy-efficiently deliver sensed information from each source to a sink node. Specifically, in mobile sink (user) applications, due to the sink mobility, a stationary dissemination path may no longer be effective. The path will have to be continuously reconfigured according to the current location of the sink. Moreover, the dynamic optimal path from each source to the sink is required in order to reduce end-to-end delay and additional energy wastage. In this paper, an Adaptive Reversal Optimal path Tree (AROT) protocol is proposed. Information delivery from each source to a mobile sink can be easily achieved along the AROT without additional control overhead, because the AROT proactively performs adaptive sink mobility management. In addition, the dynamic path is optimal in terms of hop counts and the AROT can maintain a robust tree structure by quickly recovering the partitioned tree with minimum packet transmission. Finally, the simulation results demonstrate that the AROT is a considerably energy-efficient and robust protocol.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.04a
• /
• pp.494-506
• /
• 2010

On the crisis of international economy, the government is making an effort to seek economic growing motivation with the method of overcoming economic crisis and 'low carbon green growth'. Furthermore, to promote maritime vessel traffic service related inefficient energy wastage was revealed and eco-friendly alternative energy was accepted because of high price of oil in the beginning of 2008. In this situation, I'm going to discuss the possibility of eco-friendly energy system in maritime vessel traffic service with the way of cutting the budget and expansion of solar power generation system which was promoted to meet governmental 'energy saving plan for high price of oil'.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.7B
• /
• pp.848-857
• /
• 2011

Due to the advantages of a conveniet, inexpensive installation, flexibility, and scalability, Wireless AMR systems are recently preferred over wired AMR systems. However, a multi-hop supported AMR network, which generally covers large areas, may create energy wastage problem, energy unbalance, and high interference hazard due to a large amount of concurrent-intensive metering data in the network. Therefore in this paper we propose a novel data gathering method which can solve abovementioned problems as well as conserve energy, by reducing the traffic in the network. In addition, the experimental results demonstrate that the proposed scheme shows superior performance to the conventional data transmission method.

• Journal of Nutrition and Health
• /
• v.35 no.3
• /
• pp.394-401
• /
• 2002

The purpose of this study was to : (a) examine diabetic patients' sensory evaluation and food preferences, (b) analyze the portion sizes & plate wastes, (c) investigate the factors affecting plate wastes, and (d) determine the nutritional & mometary values of the plate wastes. A questionnaire for determining food preference and sensory evaluation was developed. Thirty-three diabetic patients who were hospitalized in Sanggye Paik hospital in Seoul were studied. Serving sizes and plate wastes were weighed by using an electric scale, and the CAN-Pro program was used to evaluate the nutritional value or the food consumed. The data were analyzed using the SAS package program for descriptive analysis, t-test, ANOVA, and the Pearson correlation. Using a five-point Likeu-type scale, the temperature s[ore ranged from 3.1 to 3.3 (1 : very poor, 5 : excellent), the preference store was 3.0-3.2 (1 : very dislike, 5:very like), the taste score was 2.9-3.2 (1 : very poor, 5 : excellent), and the amount of food served score was 2.8-3.0 (1 : too little, 5 : too much). Serving sizes were considered insufficient by patients because most of the DM diet was low in calories. Average plate waste for the DM diet was 26.2% of the total served, by weight, and was lower than that for patients consuming a normal diet, which was 30.3%, found in previous research. Those subjects who had been previously hospitalized and who wished to participate in a campaign for food waste reduction produced less plate waste than other groups (p<.05). Plate wastes of the DM diet were negatively correlated with taste, temperature, and preference, and were positively correlated with the amount served: however, these results were not statistically significant. It was found that diabetic patients consumed adequate levels of energy, protein, Ca, Fe, Vitamin B$_1$, Vitamin B$_2$, and niacin, but inadequate levels of Phosphorus, Vitamin A and Vitamin C. The plate wastes were calculated to be 26.2% of the total cost (￦ 3,489), which is ￦9l5. This represents a significant wastage of resources from the hospital. The results of this study could assist foodservice managers in both controlling food wastage, and improving the quality of hospital food services.