• 신재생에너지
• /
• 제10권3호
• /
• pp.31-38
• /
• 2014

The importance of energy is growing according to the energy shortage and environmental concerns. Accordingly, in order to solve the problems about the use of fossil fuel, a renewable energy sources are needed. Global renewable energy power industry's position in the renewable energy market becomes important and new technology development is also essential. MG set composed by the induction motor and permanent magnet synchronous generator for simulating a renewable energy source is based on a suitable experiment equipment. The torque generated by applying a voltage to the induction motor in MG set is used as an input of the permanent magnet synchronous generator. In Psim simulation, the characteristics of the induction motor model was formulated and the output torque characteristics of the motor was controlled using the induction motor side inverter, In this paper, the comparison analysis between Psim simulation and the output characteristics of the MG set is performed in order to identify a renewable energy power system more accurately.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.10-22
• /
• 2008

The wind-driven doubly fed induction generator (DFIG) is currently under pressure to be more grid-compatible. The main concern is the fault ride-through (FRT) requirement to keep the generator connected to the grid during faults. In response to this, the paper introduces a novel model and new control scheme for the DFIG. The model provides a means of direct stator power control and considers the stator transients. On the basis of the derived model, a robust linear quadratic (LQ) controller is synthesized. The control law has proportional and integral actions and takes account of one sample delay in the input owing to the microprocessor's execution time. Further, the influence of the grid voltage imperfection is mitigated using frequency shaped cost functional method. Compensation of the rotor current pulsations is proposed to improve the FRT capability as well as the generator performance under grid voltage unbalance. As a consequence, the control system can achieve i) fast direct power control without instability risk, ii) alleviation of the problems associated with the DFIG operation under unbalanced grid voltage, and iii) high probability of successful grid FRT. The effectiveness of the proposed solution is confirmed through simulation studies on 2MW DFIG.

• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5893-5898
• /
• 2014

본 논문은 연료비를 최소화 할 수 있는 2차전지 전력저장장치(BESS: Battery Energy Storage System)와 풍력-디젤 복합발전시스템으로 구성되는 독립형 마이크로그리드을 모델링하는 방법과 그 운전제어 알고리즘을 제안하였다. 먼저, 부하변동 및 풍속변동에 따른 주파수와 전압을 일정하게 제어할 수 있는 양방향 DC/AC 컨버터의 BESS를 모델링하고, 디젤발전기는 공급전력의 부족 및 BESS의 충전시에만 가동하도록 하는 운전제어알고리즘을 제안한다. 그리고, 제안된 모델링 방법과 운전제어알고리즘을 독립형 마이크로그리드에 적용한 결과, 풍속 및 부하변화에 대하여 주파수와 전압변동이 적정범위내로 유지할 수 있음을 증명할 수 있었다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.3-10
• /
• 2008

Micro-electrical discharge machining (micro-EDM) is an effective method for machining all types of conductive materials regardless of hardness. Since micro-EDM is an electro-thermal process, the energy supplied by the pulse generator is an important factor in determining the effectiveness of the process. In this study, an investigation was conducted on the micro-EDM of tungsten carbide (WC) to compare the performance of transistor and resistance/capacitance (RC) pulse generators in obtaining the best quality micro-hole. The performance was measured by the machining time, material removal rate, relative tool wear ratio, surface quality, and dimensional accuracy. The RC generator was more suited for minimizing the pulse energy, which is a requirement for fabricating micro-parts. The smaller-sized debris formed by the low-discharge energy of RC micro-EDM could be easily flushed away from the machined zone, resulting in a surface free of burrs and resolidified molten metal. The RC generator also required much less time to obtain the same quality micro-hole in WC. Therefore, RC generators are better suited for fabricating micro-structures, producing good surface quality and better dimensional accuracy than the transistor generators, despite their higher relative tool wear ratio.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.949-951
• /
• 2002

Permanent-magnet (PM) synchronous generator is feasible for use with a wind turbine, because the generator for wind power requires variable-speed generation, light weight, and high torque. In this paper, basic design and construction of an axial-flux permanentmagnet generator with power output at 60 [Hz], 300 [r/min] for wind energy system is introduced. Finite-element method (FEM) is applied to analyze generator performance. In order to save time, equivalent analysis model is developed. The performance of the proposed generator at no-load and resistive load are compared, and power output and voltage at various speed and loads are compared as well. The results of FE analysis show that this PM generator is a useful solution for small-scale wind-turbine applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.439-439
• /
• 2009

Nowadays, source of MEMS, USN, Hybrid parts pay attention to energy harvesting. On this paper, energy harvesting was studied using piezoelectric effect. And, piezoelectric generator was designed and fabricated. Generators were designed by FEM simulation program and generators were made by attaching cymbal type metal plates on upper and bottom sides of a disc type piezoelectric ceramic. Output AC power was rectified to DC power by full bridge circuit and converted to regular voltage power by DC-DC converter. The final output power was charged to Ni-Cd battery. Using fabricated generators, output voltages dependant on thickness of ceramic, displacement of vibration, frequency of vibration were measured.

• 신재생에너지
• /
• 제2권3호
• /
• pp.5-9
• /
• 2006

We have fabricated a micro power generator which changes vibrational energy into useful energy. With vibrating a magnet on the surface of a winding coil, the micro power generator produce alternating voltage. We have changed the vibrational frequency from 0.5Hz to 10Hz. AC voltage of $20{\sim}25mV$ was generated at the frequency of 1Hz. When the vibration was 3Hz, AC voltage of 80mV was obtained. We have rectified and stepped up the input voltage using a quadrupler circuit. The voltage was stepped up to 130mV.

• 신재생에너지
• /
• 제9권1호
• /
• pp.17-24
• /
• 2013

Eddy Current is one of ways to make heat using rotational energy of wind turbine rotor. Four difference arrays of permanent magnets around rotor surface are used to generate heat using eddy current in this study. For the evaluation of heating performance, new test rig is prepared to measure water flow and temperatures in the inlet and outlet of the eddy current heat generator. In the test, torque and rotational speed are also measured in the motor driven system, and evaluated if the torque is matched with it of wind turbine rotor or not. It will be shown that the eddy current heat generator can be applied to real urban wind energy systems in this study.

• Nuclear Engineering and Technology
• /
• 제47권7호
• /
• pp.934-938
• /
• 2015

This technical note provides some considerations for the metallographic observation of intergranular attack (IGA) in Alloy 600 steam generator tubes. The IGA region was crazed along the grain boundaries through a deformation by an applied stress. The direction and extent of the crazing depended on those of the applied stress. It was found that an IGA defect can be misevaluated as a stress corrosion crack. Therefore, special caution should be taken during the destructive examination of the pulled-out tubes from operating steam generators.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.772-777
• /
• 2003

A vision-based tool position estimation system for the inspection and maintenance manipulator working inside the steam generator bowl of nuclear power plants can help human operators ensure that the inspection probe or plug are inserted to the targeted tube. Some previous research proposed a simplified tube position verification system that counts the tubes passed through during the motion and displays only the position of the tool. In this paper, by using a general camera calibration approach, tool orientation is also estimated. In order to reduce the computation time and avoid the parameter bias problem in an ellipse fitting, a small number of edge points are collected around the large section of the ellipse boundary. Experiment results show that the camera calibration parameters, detected ellipses, and estimated tool position are appropriate.