• 한국소음진동공학회논문집
• /
• 제23권7호
• /
• pp.597-604
• /
• 2013

Underwater acoustic sensors are significantly damaged from underwater explosion. The damage that affects sensor should be evaluated for its smooth operations and safety. For satisfying these objectives, it is necessary to obtain more accurate values of the pressure and the energy flux density by distance. This paper is divided into two part. First, to obtain more accurate value of the pressure and the energy flux density at each point, the simulation results and the reference values were compared. For fitting to the reference pressure and the reference energy flux density, the sizes of fluid and TNT model are corrected, and the comparison results show good agreements. Second, based on these results, the structural integrity of underwater sensor structure was analyzed when TNT located in 10 meters from underwater sensors structure. This simulation used the commercial software MSC/DYTRAN.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.422-426
• /
• 2005

This experimental study represents the results of an analysis on the characteristics of flux density distribution in the focal region of solar concentrator. The characteristics of flux density distributions are investigated to optimally design and position a cavity receiver. This was deemed very useful to find and correct various errors associated with a dish concentrator. We estimated the flux density distribution on the target placed along with focal lengths from the dish vertex to experimentally determine the focal length. It is observed that the actual focal point exists when the focal length is 2.17m. The total integrated power and percent power was 2467W and $85.8\%$, respectively, in the case of small dish, and also 2095W and $79\%$, respectively, in the case of KIERDISH II. As a result of the percent power within radius, approximately $90\%$ of the incident radiation is intercepted by about 0.06 m radius. The minimum radius of receiver in KIERDISH II is found to be 0.15m and approximately $90\%$ of the incident radiation is intercepted by receiver aperture.

• 한국해양환경ㆍ에너지학회지
• /
• 제10권1호
• /
• pp.53-58
• /
• 2007

하구에서 오염물은 salt finger가 발생할 수 있는 적당한 조건하에서 혼합과 수송이 일어날수 있다(Hwang and Rehmann, 2004). 선형이론을 salt finger가 일어날수 있는 적절한 조건하에 유체의 운동을 예측하는데 적용하였다. 모의 결과는 기존의 실험 결과와 거의 비슷한 결과를 도출하였다. 밀도율이 2보다 클 때, Turner(1967)가 열과 소금을 이용한 실험에서 발견한 것처럼 혼합율(the flux ratio)은 $0.55{\sim}0.57$를 보이며, 소금과 설탕을 이용한 Griffiths(1980)의 실험에서와 같이 0.87의 혼합율을 도출하였다. 두개의 매개 물질의 분자확산계수가 증가함으로써 이송속도율도 밀도율과 함께 증가하였고, 높은 밀도율에서 이송속도율이 정상상태가 되는데 걸리는 시간이 증가하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.21-23
• /
• 2002

We designed and manufactured helical magnetic flux compression generator, in which, the current density was reduced by increasing the number of wires by stages, and the voltage between wires was reduced by decreasing the time rate of inductance change. The figure of merit and the energy multiplication ratio of the generator were measured as a function of current density flowing through coil and their characteristics were analyzed. When the current density of coil was more than 250 kA/cm, the figure of merit and the energy multiplication ratio were decreased rapidly.

• Nuclear Engineering and Technology
• /
• 제36권5호
• /
• pp.420-429
• /
• 2004

The local power density should be estimated accurately to prevent fuel rod melting. The local power density at the hottest part of a hot fuel rod, which is described by the power peaking factor, is more important information than the local power density at any other position in a reactor core. Therefore, in this work, the power peaking factor, which is defined as the highest local power density to the average power density in a reactor core, is estimated by fuzzy neural networks using numerous measured signals of the reactor coolant system. The fuzzy neural networks are trained using a training data set and are verified with another test data set. They are then applied to the first fuel cycle of Yonggwang nuclear power plant unit 3. The estimation accuracy of the power peaking factor is 0.45% based on the relative $2_{\sigma}$ error by using the fuzzy neural networks without the in-core neutron flux sensors signals input. A value of 0.23% is obtained with the in-core neutron flux sensors signals, which is sufficiently accurate for use in local power density monitoring.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.127-129
• /
• 2006

In this paper, a synchronous permanent magnet planar motor (SPMPM) with Halbach array is proposed for its high energy density. The magnetization and flux density distribution are obtainedby magnet scalar potential the characteristics such as inductance, back-EMF and thrust are evaluated. It can be concluded that the analysis of SPMPM with Halbach magnet array is credible and feasible.

• 에너지공학
• /
• 제2권2호
• /
• pp.231-236
• /
• 1993

The feasibility of Magnetohydrodynamic(MHD) Ship Propulsion using Superconduction Magnets is reviewed in light of relent advances in high-temperature superconducting. The propulsion using a screw propeller in the noise reduction has it's own limitation. The epochal noiseless MHD propulsion method which does not have this disadvantage is studying nowadays. The subject of a marine MHD as propulsion has been examined before and was found to be interesting because of relatively low magnetic flux densities. It is demonstrated that the MHD propulsion is technically interesting with high magnetic flux density. The development of large-scale magnets using the high-temperature superconductor now under development could make it practical to construct submersibles for high-speed and silent operation.

• Nuclear Engineering and Technology
• /
• 제56권1호
• /
• pp.147-159
• /
• 2024

Plutonium-238 has always been considered as the one of the promising radioisotopes for space nuclear power supply, which has long half-life, low radiation protection level, high power density, and stable fuel form at high temperatures. The industrial-scale production of ²³⁸Pu mainly depends on irradiating solid ²³⁷NpO₂ target in high flux reactors, however the production process faces problems such as large fission loss and high requirements for product quality control. In this paper, a conceptual design study of producing ²³⁸Pu in a multi-purpose high flux reactor was evaluated and analyzed, which includes a sensitivity analysis on ²³⁸Pu production and a further study on the irradiation scheme. It demonstrated that the target structure and its location in the reactor, as well as the operation scheme has an impact on ²³⁸Pu amount and product quality. Furthermore, the production efficiency could be improved by optimizing target material concentration, target locations in the core and reflector. This work provides technical support for irradiation production of ²³⁸Pu in high flux reactors.

• Korean Chemical Engineering Research
• /
• 제60권4호
• /
• pp.525-534
• /
• 2022

본 연구에서는 물과 전기의 동시 생산이 가능한 pressure retarded membrane distillation (PRMD)의 폐루프식 구성 디자인을 기수담수화에 적용해 최적 운전 조건과 성능 평가를 수행하였다. 시뮬레이션 결과 80 ℃ 이상의 폐열이 공급될 때 순 에너지 생산량이 양수 값을 보이며 90 ℃ 이상일 때 안정적인 전력 생산이 가능한 것을 확인할 수 있었고 최적 유입수 유량은 0.6 kg/s를 나타냈다. 이 조건에서 3 g/L의 기수가 유입될 때 순 에너지 생산량은 2.56 W/m², 물 플럭스는 8.04 kg/m²/hr의 값을 나타냈다. 기수의 농도가 1-3 g/L로 변화할 때 물 플럭스나 에너지 생산량은 큰 변화가 나타나지 않았고, 해수가 유입수로 사용될 때와 비교하면 더 높은 물 플럭스와 순 에너지 생산량을 보였다. 이를 통해 에너지 생산이라는 측면에 집중한다면 기수를 사용해서 PRMD를 운전하는 것이 더 효율적이라는 것을 확인할 수 있었다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.11-17
• /
• 2007

Magnetization studies have been carried out on $MgB_2$ polycrystalline samples in the temperature range of 5 - 44 K and in the magnetic field up to 7 Tesla. The critical current density was calculated from hysteresis loops using the Bean's critical state model, and the highest value of $J_c$ at 20 K was $2.7{\times}10^5\;A/cm^2$ at 2 Tesla. The hysteresis loops were carefully examined to determine the temperature and magnetic field range where flux jumps appeared. The first jump occurred typically at 1 Tesla. Due to the strong pinning, we observed the presence of flux jump below H = 1 Tesla at temperature below 30 K.