• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2_spc
• /
• pp.327-336
• /
• 2020

The high-flux advanced neutron application reactor (HANARO) is a research reactor with thermal power of 30 MW applied in various research and development using neutrons generated from uranium fission chain reaction. A degasifier tank is installed in the ancillary facility of HANARO. This facility generates gas pollutants produced owing to internal environmental factors. The degasifier tank is designed to maintain the gas contaminants below acceptable levels and is monitored using an analyzer in the gas sampling panel. If condensate water is generated and flows into the analyzer of the gas sampling panel, corrosion occurs inside the analyzer's measurement chamber, which causes failure. Condensate water is generated because of the temperature difference between the degasifier tank and analyzer when the gas flows into the analyzer. A heating system is installed between the degasifier tank and gas sampling panel to suppress condensate water generation and effectively remove the condensate water inside the system. In this study, we investigated the efficiency of the heating system. In addition, the variations in the pipe temperature and the amount of average condensate water were modeled using a wall condensation model based on the changes in the fluid inlet temperature, outside air temperature, and heating cable-setting temperature.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.389-397
• /
• 2010

Concrete has excellent mechanical properties, high durability, and economical advantages over other construction materials. Nevertheless, it is not an easy task to apply concrete to long span bridges. That's because concrete has a low strength to weight ratio. Ultra high performance concrete (UHPC) has a very high strength and hence it allows use of relatively small section for the same design load. Thus UHPC is a promising material to be utilized in the construction of long span bridges. However, there is a possibility of crack generation during the curing process due to the high binder ratio of UHPC and a consequent large amount of hydration heat. In this study, adiabatic temperature rise and mechanical properties were modeled for the stress analysis due to hydration heat. Adiabatic temperature rise curve of UHPC was modeled superposing 2-parameter model and S-shaped function, and the Arrhenius constant was determined using the concept of equivalent time. The results are verified by the mock-up test measuring the temperature development due to the hydration of UHPC. In addition, models for mechanical properties such as elastic modulus, tensile strength and compressive strength were developed based on the test results from conventional load test and ultrasonic pulse velocity measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.41-41
• /
• 2008

In general, polyimides (PIs) are used in alignment layers in liquid crystal displays (LCDs). The rubbing alignment technique has been widely used to align the LC molecules on the PI layer. Although this method is suitable for mass production of LCDs because of its simple process and high productivity, it has certain limitations. A rubbed PI surface includes debris left by the cloth, and the generation of electrostatic charges during the rubbing induces local defects, streaks, and a grating-like wavy surface due to nonuniform microgrooves that degrade the display resolution of computer displays and digital television. Additional washing and drying to remove the debris, and overwriting for multi-domain formation to improve the electro-optical characteristics such as the wide viewing angle, reduce the cost-effectiveness of the process. Therefore, an alternative to non-rubbing techniques without changing the LC alignment layer (i.e, PI) is proposed. The surface of LC alignment layers as a function of the ion beam (IE) energy was modified. Various pretilt angles were created on the IB-irradiated PI surfaces. After IB irradiation, the Ar ions did not change the morphology of the PI surface, indicating that the pretilt angle was not due to microgrooves. To verify the compositional behavior for the LC alignment, the chemical bonding states of the ill-irradiated PI surfaces were analyzed in detail by XPS. The chemical structure analysis showed that ability of LCs to align was due to the preferential orientation of the carbon network, which was caused by the breaking of C=O double bonds in the imide ring, parallel to the incident 18 direction. The potential of non-rubbing technology for fabricating display devices was further conformed by achieving the superior electro-optical characteristics, compared to rubbed PI.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.1
• /
• pp.54-61
• /
• 2007

The influences of pH were investigated for anaerobic hydrogen gas production under the constant pH condition ranged from pH 3 to 10. Carbon dioxide and hydrogen gas were main components of the gas but methane was not detected in the produced gas when sucrose was added in enrichment medium. When the modified Gompartz equation was applied for the statistical analysis of experimental data, a hydrogen production potential and maximum gas production rate at pH 5 were 1,182 mL and 112.46 mL/g dry wt biomass/hr. The hydrogen conversion ratio was 22.56%. The butyrate/acetate ratios at pH 5 and pH 6 are 1.63 and 0.38. Higher butyrate/acetate ratio produced more hydrogen gas generation. The Haldane equation model was used to find the optimum pH and fitted well with the experimental data$(r^2=0.98)$. The optimum pH and specific hydrogen production were 5.5 and 119.61 mL/g VSS/h.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.417-428
• /
• 2020

Housekeeping genes are expressed in cells of all organisms and perform basic cellular functions such as energy generation, substance synthesis, cell death, and cell defense. Accordingly, the expression levels of housekeeping genes are relatively constant, and thus they are used as reference genes in gene expression studies, such as protein expression and mRNA expression analysis of target genes. However, the levels of expression of these genes may be different among various tissues or cells and may change under certain circumstances. Therefore, it is important to select the best reference gene for specific gene expression research by exploring the stability of housekeeping gene expression. This review summarizes housekeeping genes found in humans, chickens, pigs, and rats in the literature and estimates expression stability using geNorm, NormFinder, and BestKeeper software. The most suitable reference housekeeping gene can selected based on expression stability according to the experimental conditions of the gene expression study and can thus be applied to data normalization.

• Journal of Nutrition and Health
• /
• v.40 no.1
• /
• pp.78-88
• /
• 2007

The purpose of this study was to investigate dietary fat and individual fatty acids intake pattern of 174 college women living in Seoul and Gyong-gi province through internet nutritional assessment system. Each of the subjects was required to input their own food intake for three days, which included two days during the week and one day of the weekend, on the web program directly and all of the data collected were used for statistical analysis. The mean daily caloric intake of the subjects was 1,500.9 kcal which was at 71.5% of Estimated Energy Requirement (EER). Dietary fat contributed 27.6% of the total caloric intake which was slightly higher than the recommended limit of 25%. Daily cholesterol intake was 310.0 mg, which was also high to some degree. Mean daily N6 and N3 fatty acid intake was 6.1 g and 0.9 g, respectively, and calory % calculated from each were 3.63% and 0.53%. This result showed the intake of N3 fatty acid fell in Acceptable Macronutrient Distribution Ranges (AMR) $0.5\sim1.0%$ but that of N6 fatty acid was somewhat lower than the AMDR $4\sim8%$. N6/N3 ratio 8.5/l, however, was within the desirable range $4\sim10/1$. Considering overall dietary fatty acids intake, oleic acid was the most abundant, followed by linoleic and palmitic acid. And among polyunsaturated fatty acids intake, linoleic acid was exclusively high, accounting for 97.4% of total N6 fatty acid intake. On the contrary, three fatty acids, linolenic (67.3%), DHA (21.1%) and EPA (10.0%), together supplied 98.4% of total N3 fatty acid intake. Mean P/M/S was 0.9/l.1/1.0. The subjects' intake of fat, many fatty acids and cholesterol came from diverse food groups including meats, fats and oils, milk and milk products, eggs, fish, and soybean products. Nevertheless, the subjects tended to show unfavorable fat and fatty acids intake pattern in terms of quantity and quality. Based on these results, it is important to monitor dietary fat intake pattern of the general population continuously and an internet program such as the one used for this study would be valuable, especially for assessing dietary patterns in the younger generation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.143-153
• /
• 2018

Environmental regulations, which are discussed through the International Maritime Organization, focus on two aspects: the economic supply of fuel oil and, ultimately, securing next-generation energy sources. At present, there are limitations in relation to the basic quality of fuel oil and the direct relation through basic quality when applied to ships and traps in relation to environmental regulations, and the standard for the basic quality of fuel oil is generally used. There are many cases where the composition is very complicated, and the interpretation and analysis of basic quality deviate from the range of the basic standard. In other words, it is difficult to classify and apply the problem when analyzing it in connection with fuel quality and ship operations. In this paper are various factors for the basic quality of fuel oil, and a proposed possibility for the scope of the standard.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.103-111
• /
• 2018

A plasma-catalytic combined process was used as an attempt to improve the conversion efficiency of nitrogen oxides ($NO_x$) over a wide temperature range ($150{\sim}500^{\circ}C$) to cope with the exhaust gas whose temperature varies greatly. Since the catalytic $NO_x$ reduction is effective at high temperatures where the activity of the catalyst itself is high, the $NO_x$ reduction was carried out without plasma generation in the high temperature region. On the other hand, in the low temperature region, the plasma was created in the catalyst bed to make up for the decreased catalytic activity, thereby increasing the $NO_x$ conversion efficiency. Effects of the types of catalysts, the reaction temperature, the concentration of the reducing agent (n-heptane), and the energy density on $NO_x$ conversion efficiency were examined. As a result of comparative analysis of various catalysts, the catalytic $NO_x$ conversion efficiency in the high temperature region was the highest in the case of the $Ag-Zn/{\gamma}-Al_2O_3$ catalyst of more than 90%. In the low temperature region, $NO_x$ was hardly removed by the hydrocarbon selective reduction process, but when the plasma was generated in the catalyst bed, the $NO_x$ conversion sharply increased to about 90%. The $NO_x$ conversion can be maintained high at temperatures of $150{\sim}500^{\circ}C$ by the combination of plasma in accordance with the temperature change of the exhaust gas.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.139-150
• /
• 2010

Recently, full-scale research about a passenger tube train system is being progressed as a next-generation transportation system in Korea in light of global green technology. The Korea Railroad Research Institute (KRRI) has commenced official research on the construction of a tube train system. In this paper, we studied various parameters of the tube train system such as the internal tube pressure, blockage ratio, and operating speed through computational analysis with a symmetric and elongated vehicle. This study was about the aerodynamic characteristics of a tube train that operated under standard atmospheric pressure (open field system, viz., ground) and in various internal tube environments (varying internal tube pressure, blockage ratio, and operating speed) with the same shape and operating speed. Under these conditions, the internal tube pressure was calculated when the energy efficiency had the same value as that of the open field train depending on various combinations of the operating speed and blockage ratio (the P-D relation). In addition, the dependence of the relation between the internal tube pressure and the blockage ratio (the P-${\beta}$ relation) was shown. Besides, the dependence of the relation between the total drag and the operating speed depending on various combinations of the blockage ratio and internal tube pressure (the D-V relation) was shown. Also, we compared the total (aerodynamic) drag of a train in the open field with the total drag of a train inside a tube. Then, we calculated the limit speed of the tube train, i.e., the maximum speed, for various internal tube pressures (the V-P relation) and the critical speed that leads to shock waves under various blockage ratios, which is related to the efficiency of the tube train (the critical V-${\beta}$ relation). Those results provide guidelines for the initial design and construction of a tube train system.

• Nuclear Engineering and Technology
• /
• v.8 no.2
• /
• pp.101-116
• /
• 1976

An attempt is made to analyze the unit nuclear power cost of the Go-ri units 1 and 2 in terms of a set of model data. For the calculational purpose, the power cost is first decomposed into the cost components related to the plant capital, operation and maintenance, working capital requirements, and fuel cycle operation. Then, POWERCO-50 computer code is applied to enumerate the first three components and MITCOST-II is used to evaluate the fuel cycle cost component. The specific numerical results are the fuel cycle cost of Go-ri unit 2 for three alternative fuel cycles presumed, levelized unit power cost of units 1 and 2, and the sensitivity of the power cost to the fluctuation of the model data. Upon comparision of the results with the power cost of the fossil power plants in Korea, it is found that the nuclear power is economically preferred to the fossil power. Nevertheless, the turnkey contract value of Go-ri unit 2 appears to be rather expensive compared with the available data on the construction cost of the PWR plants. Therefore, it is suggested that, in order to make the nuclear power plants more attractive in Korea, the unfavorable contract of such kind must be avoided in the future introduction of the nuclear power plant. Capacity factor is of prime importance to achieving the economic generation of the nuclear electricity from the Go-ri plant. Therefore, it is concluded that more efforts should be directed to make the maximum use of the Go-ri plant.