• Journal of Radiation Protection and Research
• /
• 제26권3호
• /
• pp.305-309
• /
• 2001

Site-specific atmospheric dispersion characteristics have been analyzed. The northwest and the southwest wind prevail on nuclear sites of Korea. The annual isobaric surface averaged for twenty years around Korean peninsula shows that west wind prevails. The prevailing west wind is profitable in the viewpoint of radiation protection because three of four nuclear sites are located in the east side. Large scale field tracer experiments over nuclear sites have been conducted for the purpose of analyzing the atmospheric dispersion characteristics and validating a real-time atmospheric dispersion and dose assessment system FADAS. To analyze the site-specific atmospheric dispersion characteristics is essential for making effective countermeasures against a nuclear emergency.

• Nuclear Engineering and Technology
• /
• 제33권4호
• /
• pp.365-374
• /
• 2001

In order to examine the in-reactor performance of very-high-density dispersion fuels for high flux performance research reactors, U-l0wt.%Mo microplates containing centrifugally atomized powder were irradiated at low temperature. The U-l0wt.%Mo dispersion fuels show stable in- reactor irradiation behaviors even at high burn-up, similar to U$_3$Si$_2$ dispersion fuels. The atomized U-l0wt.%Mo fuel particles have a fine and a relatively uniform fission gas bubble size distribution. Moreover, only one of third of the area of the atomized fuel cross-sections at 70a1.% burn-up shows fission gas bubble-free zones, This appears to be the result of segregation into high Mo and low Mo.

• 한국분말재료학회지
• /
• 제25권5호
• /
• pp.395-401
• /
• 2018

The improvement of dispersion stability for the primary polishing slurry in a CMP process is achieved to prevent defects produced by agglomeration of the slurry. The dispersion properties are analyzed according to the physical characteristics of each silica sol sample. Further, the difference in the dispersion stability is confirmed as the surfactant content. The dispersibility results measured by Zeta potential suggest that the dispersion properties depend on the content and size of the abrasive in the primary polishing slurry. Moreover, the optimum ratio for high dispersion stability is confirmed as the addition content of the surfactant. Based on the aforementioned results, the long-term stability of each slurry is analyzed. Turbiscan analysis demonstrates that the agglomeration occurs depending on the increasing amount of surfactant. As a result, we demonstrate that the increased particle size and the decreased content of silica improve the dispersion stability and long-term stability.

• 천문학회보
• /
• 제36권2호
• /
• pp.94.2-94.2
• /
• 2011

Electron microbursts, energetic electron precipitation having duration less than 1 sec, have been thought to be generated by chorus wave and electron interactions. While the coincidence of chorus and microburst occurrence supports the wave-particle interaction theory, more crucial evidences have not been observed to explain the origin of microbursts. We propose the measurement of energy dispersion of microbursts could be an evidence supporting wave-particle theory. During chorus waves propagate along magnetic field, the resonance condition should be satisfied at different magnetic latitude for different energy electrons. If we observed electron microbursts at low altitude, the arrival time of different energy electrons should make unique dispersion structures. In order to observe such energy dispersion, we need a detector having fast time resolution and wide energy range. Our study is motivated from defining the time resolution and energy range of the detectors required to measure microburst energy dispersions. We performed test particles simulation to investigate how electrons interact with simple coherent waves like chorus waves. We compute a large number of electron's trajectories and successfully produce energy dispersion structures expected when microbursts are observed with 10 msec time resolution detectors at the altitude of 600 km. These results provide useful information in designing electron detectors for the future mission.

• Nuclear Engineering and Technology
• /
• 제39권5호
• /
• pp.617-626
• /
• 2007

A centrifugal atomization process for uranium fuel was developed in order to fabricate high uranium density dispersion fuel for advanced research reactors. Spherical powders of $U_3Si$ and U-Mo were successfully fabricated and dispersed in aluminum matrices. Thermal and mechanical properties of dispersion fuel meat were characterized. Irradiation tests at the research reactor HANARO confirm the excellent performance of high uranium density dispersion fuel.

• Nuclear Engineering and Technology
• /
• 제40권5호
• /
• pp.409-418
• /
• 2008

Because the interaction layers that form between U-Mo particles and the Al matrix degrade the thermal properties of U-Mo/Al dispersion fuel, an investigation was undertaken of the undesirable feedback effect between an interaction layer growth and a centerline temperature increase for dispersion fuel. The radial temperature distribution due to interaction layer growth during irradiation was calculated iteratively in relation to changes in the volume fractions, the thermal conductivities of the constituents, and the oxide thickness with the burnup. The interaction layer growth, which is estimated on the basis of the temperature calculations, showed a reasonable agreement with the post-irradiation examination results of the U-Mo/Al dispersion fuel rods irradiated at the HANARO reactor. The U-Mo particle size was found to be a dominant factor that determined the fuel temperature during irradiation. Dispersion fuel with larger U-Mo particles revealed lower levels of both the interaction layer formation and the fuel temperature increase. The results confirm that the use of large U-Mo particles appears to be an effective way of mitigating the thermal degradation of U-Mo/Al dispersion fuel.

• Nuclear Engineering and Technology
• /
• 제51권2호
• /
• pp.495-500
• /
• 2019

When a new fuel is developed, various mechanical properties are absolutely necessary for a safety analysis of the fuel for the licensing and prediction of its mechanical behavior during operation and accident conditions. In this paper, a mechanically equivalent surrogate plate of U-Mo dispersion fuel is presented using tungsten, substitute material of U-Mo particle. A surrogate plate, composed of tungsten/aluminum dispersion meat and aluminum alloy cladding, is manufactured with the same fabrication process with that of fuel plate except that a tungsten powder is used instead of U-Mo powder. A modal test showed that the surrogate plate and fuel plate have similar dynamic characteristics, and a tensile test demonstrated the similarity of the material property up to the yield strength range. The conducted tests proved that the surrogate tungsten plate has equivalent mechanical behaviors with that of a fuel plate, which leads to the acceptable use of a surrogate fuel assembly using tungsten/aluminum dispersion meat in various mechanical tests. The surrogate fuel assembly can be utilized for various out-of-pile characteristic tests, which are necessary for the licensing achievement of a research reactor that uses U-Mo dispersion fuel as a driver.

• Progress in Superconductivity
• /
• 제10권2호
• /
• pp.69-73
• /
• 2009

For extraction of the self-energy from the angle resolved photoemission spectroscopy(ARPES) experiments for the cuprate superconductors, the momentum distribution curve(MDC) analysis is commonly used. There are two requirements for this method to work: the self-energy is momentum independent and the bare electron dispersion is known. Assuming that the first condition is satisfied in the cuprates, we checked the effects of the bare dispersion on the extracted self-energy. For this, we first generated the ARPES intensity using the tight-binding band of the B2212 by solving the Eliashberg equation. We then extracted the self-energy from the theoretically generated ARPES intensity using the linear and quadratic dispersions. By choosing the bare dispersion such that the Kramer-Kronig relation is best satisfied between the real and imaginary parts of the extracted self-energy, we confirmed that the quadratic dispersion is better for the bare electron band for Bi2212. The self-energy can be reasonably extracted from the ARPES experiments using the MDC analysis.

• 방사선산업학회지
• /
• 제2권3호
• /
• pp.135-140
• /
• 2008

A field tracer experiment using radioisotope was carried out to investigate the characteristics of a pollutant transport and a determination of the dispersion coefficients in a river system. The dispersion coefficients in the longitudinal and transverse directions were determined by using the measured concentration of a radioisotope. The two-dimensional numerical models were applied to calculate the flow and concentration fields at the experimental site. Several numerical simulations were performed to investigate the effects of the numerical results according to variations of the dispersion coefficients. The calculated concentrations agreed well with the measured ones.

• Journal of Radiation Protection and Research
• /
• 제38권2호
• /
• pp.60-67
• /
• 2013

가우시안 플륨모델(Gaussian plume model)을 사용한 대기확산의 예측에서 확산계수는 결과에 중요한 영향을 미치는 변수이다. 확산계수의 평가방법은 다양하며, 본 연구에서는 미국 원자력규제위원회(U. S. NRC) 권고 규제지침, 캐나다 원자력안전위원회(CNSC) 권고 규제지침, 확률론적 사고결말해석코드 MACCS와 MACCS2에서 권고 또는 적용하는 방법을 고찰하였다. U. S. NRC에서 권고하는 부지적합성 평가를 위한 가상사고시 대기확산모델을 기반으로 확산계수의 평가방법이 대기확산인자에 미치는 영향을 분석하였다. 확산계수는 Pasquill-Gifford 곡선을 기반으로 각기 다른 연구자들에 의해 얻어진 곡선의 피팅식(curve fitting equations)을 적용 또는 권고하고 있음을 확인하였다. 수평확산계수는 모든 규제지침과 코드에서 플륨의 사행효과를 반영하여 보정하고 있으나 그 적용 방법에 있어서는 차이를 나타냈다. 수직확산계수는 U. S. NRC 권고 규제지침을 제외하고 표면거칠기를 반영하여 보정하고 있다. 특정 표면거칠기에 대해 확산계수의 적용방법에 따라 대기확산인자는 최대 약 4배의 차이를 나타냈다. 표면거칠기는 대기확산인자에 중요한 영향을 나타냈으며, 동일 적용방법에 대해 표면거칠기에 따라 대기확산인자는 약 2~3배의 차이를 나타냈다.