• Environmental and Resource Economics Review
• /
• v.22 no.3
• /
• pp.547-580
• /
• 2013

As energy conservation can be realized through changes in the composition of goods and services consumed, there is a need to assess indirect and total household energy consumption. The Korean household sector was responsible for more than 55% of Korea's total energy consumption in the 1995 to 2010 period. More than 69% of household energy consumption was indirect. Thus, not only direct but also indirect household energy consumption should be the target of energy conservation. Electricity consumption became in 2009 the main source of household energy consumption in Korea. Households consume more and more electricity intensive goods and services, a sign of increasing living standards. Decrease in energy intensities of products consumed by Korean households contributed greatly to reduce the increase in the total household energy consumption. However, switching took place towards more energy intensive products, thus the structure effect was negative. It is necessary to direct consumption and production towards much less energy intensive goods and services as to reduce energy consumption or its growth rate. The Korean government should readjust low energy and electricity prices to cost-reflective prices levels as these low prices are one of the main reasons for the consumption of more energy intensive products. This study differentiates prices of oil products and electricity between households and industries, as to allow more accurate estimation.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.2
• /
• pp.3-11
• /
• 2018

Korea has achieved a rapid economic development and with the increase in population and national income and the expansion of social and economic activities, energy consumption has rapidly increased too. Energy consumption per head has constantly increased and currently, power consumption per head is 7.5 times bigger than in 1985. Buildings occupy 25% of total energy consumption and especially, 50% of total energy is consumed for heating and cooling. In this situation, multi-family housing, which has constantly been increased, has an energy saving rate of 1.9%, which is the lowest level and this makes the government's energy policy for sustainable energy system development useless. Besides, energy consumption leads to secondary problems, such as air, water and marine pollution and heat pollution and wastewater/drainage and the increased use of fossil fuel is a fundamental reason for ozone layer destruction and global warming. Therefore, efficient energy consumption plans are required. This study aims to analyze energy performance in each block type of high-rise and diversified multi-family housing that accounts for 60% of all the housing forms, depending on the variations in stories through BIM-based energy simulation. For this study, four representative block types were selected, based on the multi-family floor plan, which is certified for energy performance evaluation and they were applied to the floor plan of a multi-family house that is scheduled to be built. Then BIM modeling was conducted from the fifth story to the 40th story at an intervals of 5 stories and based on the finding, energy characteristics of each block type and energy performance depending on the variations in stories were analyzed. It is considered that this would serve as objective data for block type and block story decision of energy performance-based multi-family housing.

• Environmental and Resource Economics Review
• /
• v.11 no.3
• /
• pp.397-414
• /
• 2002

This paper presents an empirical analysis of exchange rate volatility, petroleum's import price and industrial production on petroleum imports. The GARCH framework is used to measure the exchange rate volatility. One of the most appealing features of the GARCH model is that it captures the volatility clustering phenomenon. We found one long-run relationship between petroleum imports, import price, industrial production, and exchange rate volatility using Johansen's multivariate cointegration methodology. Since there exists a cointegrating vector, therefore, we employ an error correction model to examine the short-run dynamic linkage, finding that the exchange rate volatility performs a key role in the short-run. This paper also apply impulse-response functions to provide the dynamic responses of energy consumption to the exchange rate volatility. The results show that the response of energy consumption to exchange rate volatility declines at the first month and dies out very quickly.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.38-46
• /
• 2012

This paper discusses the energy consumption for a mid-size electric vehicle(EV) under various conditions. In order to analyze which driving style is more efficient in terms of the system of the EV, we develop the electric vehicle model and apply several types of speed profiles such as different steady speeds, acceleration/deceleration, and a real world driving cycle including the elevation profile obtained from a GPS device. The results show that the energy consumption of the EV is affected by the operating efficiency of components when driving at low speed, while it depends on required power at wheels when driving at high speed. Also this paper investigates the effect of the elevation of a road and the rate of electrical braking on the energy consumption as well as the fuel economy of a conventional vehicle model under the same conditions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1078-1085
• /
• 2011

In this paper, we analyze the relationship between energy per bit and the data rate with the variation of the system bandwidth. A existing power model is mathematical model to express power consumption of each device. In this paper, we have to investigate the system level energy model for the RF front-end of a wireless transceiver. Also, the effects of the signal bandwidth, PAR, date rate, modulation level, transmission distance, specific attenuation of frequency band, and the signal center frequency on the RF front-end energy consumption and system capacity are considered. Eventually, we analyze the relationship between energy per bit and the data rate with the variation of the system bandwidth so that we simulate the minimum energy per bit in the several Gbps data rate using Shannon capacity theory.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.3
• /
• pp.229-236
• /
• 2017

In this study, a direct contact membrane module was manufactured to be used in a pilot scale membrane distillation process to treat $3m^3/day$ of the digestate produced from anaerobic digestion of livestock manure. In order to investigate the performance of the membrane module, permeate flux was measured with and without spacer inside the module under various condition of temperature difference and cross flow velocity (CFV) through the membrane surfaces. Flux recovery rate after chemical cleaning was also investigated by applying three different cleaning methods. Additionally, thermal energy consumption was theoretically simulated based on actual pilot plant operation conditions. As results, we observed flux of the module with spacer was almost similar to the theoretically predicted value because the installation of spacer reduced the channeling effect inside the module. Under the same operating condition, the permeate flux also increased with increasing temperature difference and CFV. As a result of chemical in-line cleaning using NaOCl and citric acid for the fouled membranes, the recovery rate was 83.7% compared to the initial flux when NaOCl was used alone, and 87% recovery rate was observed when only citric acid was used. However, in the case of using only citric acid, the permeate flux was decreased at a rapid rate. It seemed that a cleaning by NaOCl was more effective to recover the flux of membrane contaminated by the organic matter as compared to a cleaning by citric acid. The total heat energy consumption increased with increasing CFV and temperature difference across the membrane. Thus, further studies should be intensively conducted to obtain a high permeate flux while keeping the energy consumption to a minimum for a practical application of membrane distillation process to treat wastewater.

• Journal of Environmental Science International
• /
• v.12 no.12
• /
• pp.1235-1243
• /
• 2003

Under controlled conditions in an environmental chamber, 24 experiments were performed to compare the ability of a Variable-Air-Volume/Bypass Filtration System(VAV/BPFS) to remove indoor pollutants and to conserve energy with the ability of conventional Variable Air Volume(VAV) system. The specific conclusions of this paper were; first, the VAV/BPFS was more efficient than the VAV system in removing particulate matter, TVOC, and target VOCs. The total effective removal rate of PM for the VAV/BPFS was two times as high as that of the VAV system. The total effective removal rate of TVOC for the VAV/BPFS was 20 percent higher than that of the VAV system. Also each target VOC concentration was reduced by using the VAV/BPFS. Second, clean air delivery rate was increased by using VAV/BPFS due to additional filtration rate. Otherwise, the VAV/BPFS decreased outdoor supply air rate above 25 percent relative to the rate of VAV system. Third, total energy consumption by the VAV/BPFS was lower than that of the VAV system during the period with indoor thermal load, occupied time. The energy saving of the VAV/BPFS ranged from 11 to 16 percent. The VAV/BPFS improves indoor air quality more efficiently than the VAV system, and it reduced energy consumption. Retrofitting the VAV system with the VAV/BPFS was easy The use of VAV/BPFS is, therefore, recommended far buildings with VAV system as well as for buildings at designing stage.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.1
• /
• pp.105-113
• /
• 2014

Currently, the energy consumption rate in buildings is approximately 28.5% of the total energy consumption in Korea. Therefore the amount of the consumption of petroleum resourses is at a worrying level of the blackout. The system of the amount of the Architectural Energy Efficiency Grade [AEEG] is in force by the government to apply the technologies of the Emissions Trading System and the Target Management System to mitigate the Green House Gases for buildings according to the climate change. On the account the mitigation of the Green House Gases and the reduction of the energy, from the view of maintenance and management, for the new and remodeling buildings should be under consideration. The author wants to present the possible ways how to improve the AEEG for the existing buildings by trying to establish the foundation of the BEMs, and by confirming the potential of the energy savings.

• Journal of Korea Society of Waste Management
• /
• v.35 no.8
• /
• pp.770-776
• /
• 2018

This study measured the energy recovery rate of each municipal waste incineration facility according to the revised energy recovery rate estimation method, which targeted four municipal waste incineration facilities (Unit No. 7). The results calculated by the measuring instruments were used for each factor to estimate the recovery rate, and the available potential of available energy was examined by analyzing the energy production and valid consumption. As a result of the low heating value, 2,540 kcal/kg was calculated on average when the LHVw formula was applied, which is approximately 116 kcal/kg higher than the average design standard of 2,424 kcal/kg. The energy recovery rate was calculated as 96.9% on average based on production and 67.5% based on effective consumption, and the analysis shows that approximately 29.4% energy can be used.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.6
• /
• pp.895-902
• /
• 2018

Energy consumption in buildings is close to 40% of the total national energy consumption in developed countries such as US and Japan, and Korea accounts for 24% of total energy consumption. In buildings, HVAC can't freely control the cooling flow rate according to the required calorie, so energy is not used efficiently. Therefore, by using the energy saving valve, the flow rate can be controlled by the required amount of heat and the energy can be saved. In this paper, we define basic conditions and develop control and monitoring boards for building energy saving valves based on PIC processor with low power and high cost-effectiveness. The designed board displays and transmits in real time information about two temperature values, flow values and calculated calories for temperature difference measurement. The developed board will be useful for real - time monitoring of the state of the valve in the future and development of the valve for the offshore.