• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1821-1830
• /
• 2001

The flow around free end of a finite circular cylinder (FC) embedded in an atmospheric boundary layer has been investigated experimentally. The experiments were carried out in a closed-return type subsonic wind tunnel with varying aspect ratio of the finite cylinder mounted vertically on a flat plate. The wakes behind a 2-D cylinder and a finite cylinder located in a uniform flow were measured for comparison. Reynolds number based on the cylinder diameter was about Re=20,000. A hot-wire anemometer was employed to measure the wake velocity and the mean pressure distributions on the cylinder surface were also measured. The flow past the FC free end shows a complicated three-dimensional wake structure and flow phenomenon is quite different from that of 2-D cylinder. The three-dimensional flow structure was attributed to the downwashing counter rotating vortices separated from the FC free end. As the FC aspect ratio decreases, the vortex shedding frequency decreases and the vortex formation length increases compared to that of 2-D cylinder. Due to the descending counter-rotating twin-vortex, near the FC free end, regular vortex shedding from the cylinder is suppressed and the vortex formation region is hardly distinguished. Around the center of the wake, the mean velocity for the FC located in atmospheric boundary layer has large velocity deficit compared to that of uniform flow.

• 한국환경보건학회:학술대회논문집
• /
• 한국환경보건학회 2003년도 Challenges and Achievements in Environmental Health
• /
• pp.136-139
• /
• 2003

This study is to observe the occurrence of heterotrophic bacteria in terms of free chlorine residuals in two different water distribution system which belongs to both K and Y water treatment plant of S city of Korea. The data analyzing in distribution systems (DS) shows that the free chlorine residuals decrease from 0.10 to 0.56 mgmg/L for K, and 0.51 to 0.78 mg/L for Y. The decay of free chlorine is clearly higher in both March and August than those of in January. The HPC in DS are ranged from 0 to 40 CFU/mL for K, 0 to 270 CFU/mL for Y, on R2A medium. In particular, its level is relatively high at consumers ground storage tanks, taps and point-of-end area of Y. The predominant genera is studied in distribution systems are Acinetobacter, Sphingomonas (branch of Pseudomonas), Micrococcus, Bacillus, Staphylococcus. The diversity of heterotrophic bacteria increase in the end-point area. Most of them are either encapsulated cells or cocci of gram-positve. In conclusion, the point-of-end area in distribution systems shows the longer flow distance from water treatment plants, the greater diversity and higher level of heterotrophic bacteria due to the significant decay of free chlorine residuals.

• Structural Engineering and Mechanics
• /
• 제31권4호
• /
• pp.453-475
• /
• 2009

The literature regarding the free vibration analysis of Bernoulli-Euler and Timoshenko beams on elastic soil is plenty, but the free vibration analysis of Reddy-Bickford beams on elastic soil with/without axial force effect using the Differential Transform Method (DTM) has not been investigated by any of the studies in open literature so far. In this study, the free vibration analysis of axially loaded Reddy-Bickford beam on elastic soil is carried out by using DTM. The model has six degrees of freedom at the two ends, one transverse displacement and two rotations, and the end forces are a shear force and two end moments in this study. The governing differential equations of motion of the rectangular beam in free vibration are derived using Hamilton's principle and considering rotatory inertia. Parameters for the relative stiffness, stiffness ratio and nondimensionalized multiplication factor for the axial compressive force are incorporated into the equations of motion in order to investigate their effects on the natural frequencies. At first, the terms are found directly from the analytical solutions of the differential equations that describe the deformations of the cross-section according to the high-order theory. After the analytical solution, an efficient and easy mathematical technique called DTM is used to solve the governing differential equations of the motion. The calculated natural frequencies of one end fixed and the other end simply supported Reddy-Bickford beam on elastic soil using DTM are tabulated in several tables and figures and are compared with the results of the analytical solution where a very good agreement is observed and the mode shapes are presented in graphs.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.88-93
• /
• 1997

Ball-end milling process is widely used in the die and mold manufacturing because of suitable for the machining of free-form surface. Pencil cutting can eliminate overload in uncut area caused by large diameter of ball-end mill before finish cutting. As the ball-end mill for pencil cutting is long and thin, it is easily deflected by cutting force. The tool deflection when pencil cutting is one of the main reason of the machining errors on a free-from surface. The purpose of the research is to find out the characteristics of deflected cutter trajectory by eddy-current sensor.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.177-183
• /
• 1994

The ball-end milling process is widely used in the die/mold industries, and it is very suitable for the machining of free-from surfaces. However, cusps(or scallops) remaining at the machined part along the cutter paths require anothe finish process such as polishing or grinding. In this study, a high sped micro ball-end milling method has been suggested for the finish of free- form surfaces. A new tool path which makes the geometrical roughness of workpiece be constant through the machined surface has been developed. In the high speed machining of micro ball-end muling experimets, the developed tool paths have been successfully applied. And it was concluded that the surface roughness from this finish cuts of micro ball-end milling process was acceptable.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.245-252
• /
• 2000

Model tests on free standing pile groups and piled footings with varying a pile spacing in two layered soils are carried out. The influence of pile cap on the behaviors of end bearing pile groups is analyzed by comparing the bearing behavior in piled footings with those in a single pile, a shallow footing(cap alone) and free standing pile groups. From the test results, it is found that the bearing characteristics of cap-soil-pile system are related with load levels and pile spacings. Before yield, the bearing resistance by cap is not fully mobilized, however, as the applied load increases, the bearing resistance of cap approaches to that of cap alone and settlement hardening occurs after yield due to the compaction caused by the contact pressure between cap and soil. By the cap-soil-pile interaction, shaft friction and point resistance of piles considerably increase with dependency of pile spacings. In two layered soil, the increasing effect of dilatancy in dense sandy soil adjacent to pile tips, increases the point resistance of pile.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.28-38
• /
• 1986

An analytical and experimental investigation is made to the dynamic responese of a cantilever with a tip mass that models some of the basic phenomena involved in the response of a flexible manipulator with a tip mass on its free end under the given rotating motion. The system equation is derived from the Hamilton's principle on the basis of the Euler-Bernoulli hypothesis and an approximate solution is obtained from model analysis using Galerkin's method for the vibation response of the system subjected to a sudden stop after an impulsive rotation. Experiment was performed to verify the validity of the theoretical analysis. Results are given for the vibration amplitude of the free end with respect to tip mass ratio, non-dimensionalized rotating velocity, rotating angle and non- dimensionalized hub length. The rotating condition to minimize the vibration amplitude of the free end can be determined for the given basic paramenters.

• Archives of Reconstructive Microsurgery
• /
• 제22권1호
• /
• pp.33-37
• /
• 2013

Purpose: The concept and development of perforator free flaps have led to significant advances in microsurgery. Ongoing developments in perforator free flap surgery are aimed at reducing complications and improving surgical outcomes. The aim of this study was to evaluate the effectiveness and application of supermicrosurgery in free flap surgery. Materials and Methods: A total of 267 patients with soft tissue defects of the lower extremity due to various etiologies from January, 2007 to January, 2013. The patients received either an anterolateral thigh free flap (n=83), a superficial circumflex iliac artery free flap (n=152), an upper medial thigh free flap (n=19), or a superior gluteal artery perforator free flap (n=13). Microanastomosis was performed using a perforator-to-perforator technique, either end-to-end or end-to-side. Results: The mean postoperative follow up period was eight months (range: one to 16 months) and flap loss occurred in 11 cases out of 267. All cases of flap loss occurred within two weeks of surgery due to either arterial insufficiency (n=5) or venous congestion (n=6). Conclusion: Supermicrosurgery enables the selection of the most efficient perforator for microanastomosis at the defect site. It also reduces the time required for dissection of recipient vessels, and reduces the possibility of injury to major vessels. Microsurgery using a vessel of less than 1 mm has been reported to increase the risk of flap failure; however, using the most advanced surgical tools and developing experience in the technique can produce success rates similar to those found in the literature.

• Structural Engineering and Mechanics
• /
• 제14권5호
• /
• pp.611-624
• /
• 2002

In this paper, a complete solution is presented for dynamic plastic response of a rigid, perfectly plastic hinged-free beam, of which one end is simply supported or hinged and the other end free, subjected to a transverse strike by a travelling mass at an arbitrary location along its span. The governing differential equations are expressed in non-dimensional forms and solved numerically to obtain the instantaneous deflection of the beam and the plastic dissipated energy in the beam. The dynamic behavior for a hinged-free beam is more complicated than that of a free-free beam. It transpires that the mass ratio and impact position have significant influence on the final deformation. In the aspect of energy dissipation, unlike simply supported or clamped beams for which the plastic deformation consumes almost the total input energy, a considerable portion of the input energy would be transferred as rigid-body motion of hinged-free beam, and the energy dissipated in its plastic deformation is greatly reduced.

• Archives of Reconstructive Microsurgery
• /
• 제7권1호
• /
• pp.1-9
• /
• 1998

From January 1985 to February 1997, 96 patients had undergone the free vascularized groin flap on the upper and lower extremities with microsurgical technique at the department of orthopaedic surgery, Yonsei University College of Medicine. The results were as follows: 1. Average age at the time of operation was 24.9 years. and there were 71 men and 25 women and mean follow up was 62.4 months. 2. The lesion site was 82 cases on the lower extremity: foot(40), leg(20), ankle(13), and 14 cases on the upper extremity: forearm(6), elbow(3), hand(3), wrist(2). 3. The anatomical classification of the superficial circumflex iliac artery was as follows: 1) 39.8% of common origin with superficial inferior epigastric artery, 2) 30.1% of isolated origin and absent superficial inferior epigastric artery, 3) 13.3% of separate origin, 4) 16.9% of origin from the deep femoral artery. 4. There was no statistical significance on arterial anastomosis between end to end and end to side, and on venous anastomosis(end to end) between one vein and two veins. 5. The success rate was average 84.4% in 81 of 96 cases. 6. In the 15 failed cases, the additional procedures were performed: 5 cases of free vascularized scapular flap, 6 cases of full thickness skin graft, 2 cases of cross leg flap, 1 case of latissimus dorsi flap, 1 case of split thickness skin graft. In conclusion, the free vascularized groin flap can be considered as the treatment of choice for the reconstruction of the extensive soft tissue injury on the extremities, and show the higher success rate with the experienced surgeon.