• Applied Biological Chemistry
• /
• v.47 no.1
• /
• pp.72-77
• /
• 2004

The purpose of this research was to determine the effect of phenol compounds from green tea leaves and surfactant micelles on lipid oxidation in com oil-in-water emulsion (O/W). The concentration of phenol and surfactant in continuous phase of the O/W with exceed Brij 700 and phenol compounds was measured. The particle size of O/W with phenol (100 ppm) increased with increasing added exceed surfactant $(0{\sim}2.0%)$ and the concentration of surfactant and phenols in the continuous phase higher than these of control. Lipid oxidation rates, as determined by the formation of lipid hydroperoxides and headspace hexanal, in the O/W emulsions containing phenol compounds (100 ppm) and exceed surfactant $(0{\sim}2.0%)$ decreased with increasing concentration of exceed surfactant. The ability of the phenol compounds and exceed surfactant to inhibit hydroperoxide and headspace hexanal producing as lipid oxidation in O/W was BHT>procyanidin B3-3-O-gallate> (+)-gallocatechin > (+)-catechin and 2% > 1 % > 0% of exceed surfactant. These results indicate that phenol compounds and exceed surfactant could alter the physical location of hydroperoxide in O/W.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.99-107
• /
• 1997

This study Provides the treatment methods of liquid wastes from the dissolution/purification process of nuclear fuel raw material and the fabrication process of nuclear fuel powder. One of the treatment methods is to process liquid waste from uranium raw material dissolution/purification process. This waste, of the strong acid, can be reused to dissolve the fine ADU particles in filtrate which is ADU waste of pH 8.0 converted from AUC waste after recovery of uranium. To dissolve the fine ADU particles, ADU filtrate was pretreated to pH 4.0 with the dissolution/purification waste, and then mixed with the lime to pH 9.2 and aged for 30 minutes. From this processing, uranium content of the filtrate was decreased to below 3ppm. The waste from fuel powder fabrication is emulsified solution dispersed with fine oil droplets. This emulsion was destroyed effectively by adding and mixing the nitric acid with rapid heating at the same time. After this processing, $Na_2U_2O_7$ compound is produced by addition of NaOH. Optimum condition of this processing was shown at pH 11.5, and uranium content of the filtrate was analyzed to 5ppm. To remove the trace of uranium in the filtrate, lime should be added. Otherwise, 4N nitric acid was used to destroy the emulsion directly, and then lime was added to this waste. Uranium content of the treated filtrate was below 1 ppm. In addition to these wastes, the trace of uranium in filtrate after recovery of uranium from the AUC waste which is produced during PWR power preparation, is treated with NaOH to takeup fluorine(F) in the waste because fluorine is valuable and toxic material. In the finally treated waste, uranium was not detected.

• Membrane and Water Treatment
• /
• v.7 no.3
• /
• pp.175-191
• /
• 2016

In this work, oil-in-water emulsions (O/W) were prepared successfully by membrane emulsification with $0.5{\mu}m$ pore size membrane. Sunflower oil was emulsified in aqueous Tween80 solution with a simple crossflow apparatus equipped with ceramic tube membrane. In order to increase the shear-stress near the membrane wall, a helical-shaped reducer was installed within the lumen side of the tube membrane. This method allows the reduction of continuous phase flow and the increase of dispersed phase flux, for cost effective production. Results were compared with the conventional cross-flow membrane emulsification method. Monodisperse O/W emulsions were obtained using tubular membrane with droplet size in the range $3.3-4.6{\mu}m$ corresponded to the membrane pore diameter of $0.5{\mu}m$. The final aim of this study is to obtain O/W emulsions by simple membrane emulsification method without reducer and compare the results obtained by membrane equipped with helix shaped reducer. To indicate the results statistical methods, $3^p$ type full factorial experimental designs were evaluated, using software called STATISTICA. For prediction of the flux, droplet size and PDI a mathematical model was set up which can describe well the dependent variables in the studied range, namely the run of the flux and the mean droplet diameter and the effects of operating parameters. The results suggested that polynomial model is adequate for representation of selected responses.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.42 no.2
• /
• pp.127-133
• /
• 2016

In this study, water-in-oil (W/O) nanoemulsions of water/Span 80-Nikkol BL 25/oil system were prepared by the PIC method at elevated temperature. This method allows the formation of finely dispersed W/O nanoemulsions with low viscosity in this system. However, macroemulsions rather than nanoemulsions were prepared by PIC method at room temperature. As a result of the significant change of interfacial tension with temperature, the emulsion droplet size decreases from $2{\mu}m$ to 100 nm with the increase in temperature from $30^{\circ}C$ to $80^{\circ}C$. The droplet size of nanoemulsions prepared at $80^{\circ}C$ was in the range of 50 ~ 200 nm and the internal phase content could reach as high as 15 wt%. The most stable nanoemulsion was formed in the vicinity of 7.0 of optimum HLB of the emulsifier mixture. The obtained nanoemulsions were stable without obvious change in droplet size in one month. This study provides valuable information for optimizing the formation of W/O nanoemulsions with low viscosity. These results suggest that W/O nanoemulsions of low viscosity could be useful for cosmetics with soft feeling.

• Macromolecular Research
• /
• v.9 no.5
• /
• pp.267-276
• /
• 2001

In order to endow with new bioactive functionality from demineralized bone particle (DBP) as natural source to poly(L-lactide) (PLA) synthetic biodegradable polymer, porous DBP/PLA as natural/synthetic composite scaffolds were prepared and compared by means of the emulsion freeze drying and solvent casting/salt leaching methods for the possibility of the application of tissue engineered bone and cartilage. For the emulsion freeze drying method, it was observed that the pore size decreased in the order of 79$\mu\textrm{m}$ (PLA control) > 47$\mu\textrm{m}$ (20% of DBP) > 23 $\mu\textrm{m}$ (40% of DBP) > 15$\mu\textrm{m}$ (80% of DBP). Porosities as well as specific pore areas decreased with increasing the amount of DBR. It can be explained that DBP acts like emulsifier resulting in stabilizing water droplet in emulsion. For the solvent casting/salt leaching method, a uniform distribution of well interconnected pores from the surface to core region were observed the pore size of 80 ∼70 $\mu\textrm{m}$ independent with DBP amount. Porosities as well as specific pore areas also were almost same. For pore size distribution by the mercury intrusion porosimeter analysis between the two methods, the pore size distribution of the emulsion freeze drying method was broader than that of the solvent casting/salt leaching method due to the mechanism of emulsion formation. Scaffolds of PLA alone, DBP/PLA of 40 and 80%, and DBP powder were implanted on the back of athymic nude mouse to observe the effect of DBP on the induction of cells proliferation by hematoxylin and eosin staining for 8 weeks. It was observed that the effect of DBP/PLA scaffolds on bone induction are stronger than PLA scaffolds, even though the bone induction effect of DBP/PLA scaffold might be lowered than only DBP powder, that is to say, in the order of DBP only > DBP/PLA scaffolds of 40 and 80% DBP > PLA scaffolds only for osteoinduction activity. In conclusion, it seems that DBP plays an important role for bone induction in DBP/PLA scaffolds for the application of tissue engineering area.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.26 no.1
• /
• pp.261-274
• /
• 2000

The o/w emulsions were prepared with saccharide surfactants which were sucrose monostearate(S160), sucrose distearate(S110), and POE(20) methyl glucose stearate(SSE20). And for emulsion the oils used were n-hydocarbon, squalane(SQ), liquid paraffin(LP), octylpalmitate(OP), octylstearate(OS), alkyl benzoate(AB), isostearyl benzoate(ISB). The structures of o/w emulsion droplet were investigated by laser light scattering and the fractal dimensions were calculated from light intensity curves. Increasing of concentration, chain length, and nonpolarity of oils, fractal dimensions of emulsion droplets were found greater. In general fiactal dimensions were varied from 1.7 to 2.8 and its structures were fractal But the fractal dimensions of octadecane( $C_{18}$), 50, and LP emulsified with S110 and S160 were varied from 3.0 to 3.2 and its structures were more dense. The overall fractal dimensions of S110 and S160 were varied from 2.1 to 2.6, that of SSE20 were varied from 1.5 to 2.1. So it was found that the structures of SSE20 system were less compact than that of S110 and S 160 system, because the hindrance effect of polyoxyehtylene group of SSE20 was stronger than that of sucrose of S160. The strucures of emulsion droplets changed according to the nature of emulsifiers and to compositions of oil substances which they contained, and the structures were found similar when the hydophilic moiety of emulsifiers was same.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.299-306
• /
• 2023

In this study, the O/W emulsification processes with the natural surfactants that were extracted from Medicago sativa L. and Sapindus saponaria L. as emulsifiers were optimized using the central composite design-response surface methodology (CCD-RSM). Herein, independent parameters were the amounts of mixed emulsifiers, the mixing ratio of natural emulsifiers (soapberry saponin/alfalfa saponin), and the emulsification time, whereas the reaction parameters were the emulsion stability index (ESI), mean droplet size (MDS), and antioxidant activity (DPPH radical scanvenging activity). Through basic experiments, the ranges of operation variables for the amount of mixed emulsifiers, the mixing ratio of natural emulsifiers, and the emulsification time were 12~14 wt%, 30~70%, and 20~30 min, respectively. The optimum operation variables deduced from CCD-RSM for the amount of mixed emulsifiers, the mixing ratio of natural emulsifiers, and the emulsification time were 13.2 wt%, 44.2%, and 25.8 min, respectively. Under these optimal conditions, the expected values of the ESI, MDS, and antioxidant activity were 88.7%, 815.5 nm, and 38.7%, respectively. And, the measured values of the ESI, MDS, and antioxidant activity were 90.6%, 830.2 nm, and 39.6%, respectively, and the average experimental error for validating the accuracy was about 2.1%. Therefore, it was possible to design an optimization process for evaluating the O/W emulsion process using CCD-RSM.

• Journal of Biosystems Engineering
• /
• v.21 no.1
• /
• pp.10-20
• /
• 1996

관개방제 기술의 변수 및 효력예측을 위한 컴퓨터 시뮬레이션 프로그램이 유화/산화액적의 부착율, 유충의 추계적 난보운동 및 무작위 농약흡수 이론을 이용하여 개발되었다. 시뮬레이션 결과는 밤나방 유충, Spodaptera frugiperda (J.E. Smith) (Lepidoptera : Noctuidae)을 이용한 방제효력 실험결과와 비교하였다. 이론치와 실험치는 서로 일치되었다. 방제율은 농약유효성분량이 증가함에 따라 증가하였으며 크로포(chlorpyrifos) 약제의 표준 권고량인 670g[AI]/ha에서 완전방제가 예상되었다. 유화액적(emulsion)은 상대적으로 직경이 큰 산화액적(dispersion) 보다 작물잎 표면에 부착이 어려워 낮은 방제율을 나타내었다. 액적직경이 방제효력에 미치는 영향은 목화작물에 대하여 낮은 약제량에서 뚜렷하게 나타났고, 그 영향은 약제량이 증가할수록 목화 및 옥수수 모두에서 저하되었다. 엽형계수는 작물의 엽상구조에 따른 액적의 부착 및 계류에 미치는 영향을 의미한다. 고찰된 관계방제기술의 영향요소에 대한 이해는 농약사용의 감소 및 효력의 증가에 중요한 역할을 한다.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.821-824
• /
• 2009

In this study, a hydrogenated lecithin-containing nanoemulsion was prepared from hydrogenated lecithin and silicone oil. Tween-60 and liquid paraffin, widely known emulsifiers, were used as standard substances, and high shear was produced by utilizing a high shear homogenizer and microfluidizer. The properties of the nanoemulsion prepared with hydrogenated lecithin were evaluated by measuring interfacial tension, dynamic interfacial tension, droplet size, zeta-potential, friction force, skin surface hygrometery, and dermal safety. The interfacial tension of lecinol S10/silicone oil was lower than that of lecinol S10/liquid paraffin. The nanoemulsion prepared from hydrogenated lecithin shows lower zeta-potential, skin surface hygrometery, and friction force compared with a general emulsion. The silicone nanoemulsion prepared from hydrogenated lecithin showed a zero value in the patch test and thus exhibits high dermal safety.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.2
• /
• pp.44-52
• /
• 2000

The dispersion of surface oil is generally described as a break-up of oil slick into small oil droplets. These small droplets are subjected to turbulence and vertical circulation so that it can be entrained into subsurface. Sometimes they tend to be submerged into sea bottom permanently. The diameter of oil droplets is a critical parameter to determine their behavioral characteristics under water surface. At the same time the variations of droplet stability depends on the weathering of it. That is why the weathered oil has different mechanism from the unweathered one. The variability of physical properties of oil including viscosity and density contribute to interfere with effective separation of oil and emulsion droplets in water. Also in the presence of interactions among the droplets there are coalescing or coagulating effects on the dispersion process of droplets.