• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.181-187
• /
• 2008

Recently, alternative fuels are drawing more attentions due to the increasing need for lower emission characteristics and fuel consumption rate in automotive engines. The GTL(gas to luquid) is the one of most favored candidates. It has higher cetane number(more than 75) and almost negligible sulphur and aromatic contents. Therefore, enhanced emission characteristics are expected even in the application in diesel engines without any modification. In this study, the cylinder pressure and heat release, emission characteristics with fuel injection timings are compared between diesel and GTL fuel in the single cylinder diesel engine. Noticeable reduction in PM, THC and CO emission are observed due to lower sulphur and aromatic contents in GTL. Also, the ignition delay decreased due to higher cetane number of GTL, which slightly decreased the amount of NOx emissions. With the retards of main injection timing, NOx decreases more for the case of GTL, while the level of THC and CO emissions still remains lower than the case of diesel. Therefore, there is much room for the control of injection timing for NOx reduction without sacrificing THC and CO emissions. With the retards of main injection timing, Small size distribution of PM became lager and there amount increased. But from all conditions, size distribution of PM for the case GTL was lower than Diesel.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1031-1035
• /
• 2008

The importance of the more efficient cogeneration system is emphasized. Also the more clean energy is needed at recent energy system. The cogeneration system using Lean burn engine is more preferred to the system using Rich burn engine because of the electrical efficiency. Although the cogeneration system using Lean burn engine is economically preferred, because of the NOx emission level, the system using Rich burn engine with 3-way catalyst can only be used in Korea. The NOx regulation level is 50ppm at oxygen level 13%. The cogeneration hybrid system is consist of Lean burn gas engine, afterburner, boiler, economizer, DeNOx catalyst, combustion catalyst, absorption chiller, cooling tower and grid connection system. The system was accurately evaluated and the result is following ; 90% total efficiency, below 10ppm NOx, 50ppm CO, 25ppm UHC. The cogeneration hybrid system can meet the NOx level and exhaust gas regulation. It can achieve the clean combustion gas and efficient cogeneration system.

• Journal of Environmental Policy
• /
• v.5 no.1
• /
• pp.1-23
• /
• 2006

This study explores what potential future greenhouse gas allocation schemes might mean for OECD countries, and discusses a number of concepts of equity, examines three specific burden sharing rules and formulae. The results indicate that Korea reduces its emission from 8.1% and 19.8% which is 34.9-85.8 million tons of $CO_2$ emission on the assumption that the overall level of abatement remains 20% of total 2000 OECD emissions.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.34-39
• /
• 2008

The combustion purpose of diesel engine is to reduce the emission of green gas and to produce high output. Generally, the regulation matter of emission gas is largely diveded by 'THC', 'NOx', 'CO' and 'PM'. Among those matters, the most problem is to disgorge into 'PM', the character of diesel combustion. Diesel PM can be controlled using Diesel Particulate Filter, which can effectively reduce the level of soot emissions to ambient background levels. $NO_2$ generated by the DOC is used to combust the carbon collected in the DPF at low temperature. To certificate DPF device that is suitable to domestic circumstances, it is necessary to exactly evaluate the DPF devices according to the regulation of DPF certificate test procedure fur retrofit. To do carry out the above-mentioned description the understanding of that regulation like the standard of PM reduction is needed. In this study the test procedure including test cycle and BPT test condition was examined, and also the test result for specific DPF was analyzed. In every test like field test, PM reduction efficiency test and Seoul-10 mode test, no defect was showed.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.1
• /
• pp.23-30
• /
• 2011

International cooperation to reduce greenhouse gas emissions is expected to provide a big crisis and a great opportunity at the same time for our industry that heavily consumes energy. To cope actively with the international environmental regulation, such as the Framework Convention on Climate Change, quantitative measurement of the volume of greenhouse gases emitted by various industries and quantitative prediction of the greenhouse gas emissions of the future are becoming more important than anything else at the national level. This study aims to propose the calculation process of carbon dioxide($CO_2$) emission for building in life cycle. This paper describes and compares 9 different tool for environmental load estimation with LCA. This study proposed the calculation process for quantitatively predicting and assessing $CO_2$ emissions during the life cycle of buildings based on the life cycle assessment(LCA). The life cycle steps of buildings were divided into the design/supervision, new construction, repair, renovation, use of operating energy in buildings, maintenance, and reconstruction stage in the life cycle inventory analysis and the method of assessing the environmental load in each stage was proposed.

• Journal of Energy Engineering
• /
• v.10 no.3
• /
• pp.188-194
• /
• 2001

The process simulations are made on the IGCC power plant using heavy residue oil from refinery process. In order to model combined power block of IGCC, the present study employs the gas turbine of MS7001FA model integrated with ASU (Air Separation Unit), and considers the air extraction from gas turbine and the combustor dilution by returned nitrogen from ASU. The exhaust gas energy of gas turbine is recovered through the bottoming cycle with triple pressure HRSG (Heat Recovery Steam Generator). Clean syngas fuel of the gas turbine is assumed to be produced through Shell gasification of Visbreaker residue oil and Sulfinol-SCOT-Claus gas cleanup processes. The process optimization results show that the best efficiency of IGCC plant is achieved at 20% air extraction condition in the case without nitrogen dilution of gas turbine combustor find at the 40% with nitrogen dilution. Nitrogen dilution of combustor has very favorable and remarkable effect in reducing NOx emission level, while shifting the operation point of gas turbine to near surge point.

• Journal of Institute of Convergence Technology
• /
• v.12 no.1
• /
• pp.19-23
• /
• 2022

Interest in hydrogen production to respond to climate change is increasing. Until now, hydrogen has been mainly produced through the SMR (Steam Methane Reforming) process using natural gas. A large amount of CO₂ is emitted in the hydrogen production process through SMR, and the gas flow including CO₂ generated in the SMR process has different characteristics for each emission source, so it is important to apply a suitable CO₂ capture process. In the case of PSA tail gas or synthesis gas, the applicability of an amine-based process has been confirmed or demonstrated close to a commercial level. However, in the case of the flue gas generated from the reformer, it is still difficult to apply the conventional amine-based process because the partial pressure of CO₂ is relatively low. Energy-saving innovative absorbents such as phase separation absorbents can be a solution to these difficulties.

• Journal of Korea Technology Innovation Society
• /
• v.11 no.2
• /
• pp.264-286
• /
• 2008

In 2006, the share of energy in Korea amounted to 28% from the total import, 97% from overseas dependency, and 83% for the national Greenhouse Gas (GHG) emission in 2004. Thus, from the aspects of economical and environmental policies, an energy analysis is very important, for the industry to cope with the imminent pressure for climate change. However, the estimation of GHG gas emissions due to an energy use is still done in a primitive way, whereby each industry's usage is multiplied by coefficients recommended from international organizations in Korea. At this level, it is impossible to formulate the prevailing logic and policies in face of a new paradigm that seeks to force participation of developing countries through so called post-Kyoto Protocol. In this study, a hybrid energy input-output (E-IO) analysis is conducted on the basis of the input-output(IO) table of 2000 issued by the Bank of Korea in 2003. Furthermore, according to economic sectors, emission of the GHG relative to an energy use is characterized. The analysis is accomplished from four points of view as follows: 1) estimating the GHG emission intensity by 96 sectors, 2) measuring the contribution ratio to GHG emissions by 14 energy sources, 3) calculating the emission factor of 3 GHG compounds, and 4) estimating the total amount of national GHG emission. The total amount estimated in this study is compared with a national official statistical number. The approach could be an appropriate model for the recently spreading concept of a Life Cycle Analysis as it analyzes not only a direct GHG emission from a direct energy use but also an associated emission from an indirect use. We expect this model can provide a form for the basis of a future GHG reduction policy making.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.91-97
• /
• 2023

Aging construction machinery and vehicles with old diesel engines usually have a long life span, so they continue to emit harmful emissions. Therefore, replacing these older diesel engines with engines that meet the latest emisstion standard is expected to help improve air quality, and engines with propane fuels, which are easily available at construction sites, can be an appropriate alternative. In this study, a propane fueled engine was developed based on a 6.8-liter CNG engine, and technologies such as gas injectors, exhaust gas recirculation (EGR), and enhanced catalysts were applied. As a result, nitrogen oxides achieved half of the emission performance at the Stage-V level, the latest emission standard, while securing diesel engine output and torque in the same class.

• Journal of Environmental Health Sciences
• /
• v.34 no.4
• /
• pp.316-326
• /
• 2008

The Earth's temperature has risen $0.76^{\circ}C$ (degree) during last 100 years which Implies a sudden rise, compare with the 4oC (degrees) rise through out the past 20,000 years. If the volume of GHG (Greenhouse Gas) emission continues at the current level, the average temperature of the Earth will rise by $1^{\circ}C$ (degree) by 2030 with the further implication that the temperature of Earth will rise by $2{\sim}5^{\circ}C$ (degrees) every 100 years. Therefore, as we are aware that the temperature of the glacial epoch was $8{\sim}9^{\circ}C$ (degrees) lower than the present time, we can easily predict that the above temperature rises can be potentially disastrous for human life. Every country in the world recognizes theseriousness of the current climate change and adopted a convention on climate change in June 1992 in Rio. The COP1 was held in March 1995 in Berlin and the COP3 in Dec. 1997 in Kyotowhere the target (2008-2012) was determined and the advanced nations' reduction target (5.2%, average)was also agreed at this conference. Korea participated in the GHG reduction plan which required the world's nations to ratify the Kyoto Protocol. Ratification of the Kyotoprotocol and the followup requirement to introduce an international emissions trading scheme will require severe reductions in GHGs and considerable economic consequences. USA are still refusing to fully ratify the treaty as the emission reductions could severely damage the economies of these countries. In order to estimate the exact $CO_2$ emission, this study statistically analyzed $CO_2$ emission of each country based on the following variables : level of economic power and scientific development, the industrial system, productivity and energy efficiency.