• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• Asian Journal of Atmospheric Environment
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2010

The effectiveness of the government regulation on tail-pipe emission for diesel vehicles issued in 2003 in Tokyo was evaluated in this study. Variations in annual average concentrations of polycyclic aromatic hydrocarbons (PAHs) and nitro-PAHs associated with airborne particulate matter were investigated in connection with the variation in airborne elemental carbon (EC) concentration in downtown Tokyo, Japan in 2006-2007 and in 1997-1998. The annual average concentrations of EC, seven different PAHs, and 1-nitropyrene were found to have decreased significantly from 1997-1998 to 2006-2007. The most prominent decrease in atmospheric concentration was observed for 1-nitropyrene, which is a representative nitro-PAH originating from diesel vehicles. This indicated that the government control has worked to considerably reduce both atmospheric mutagens and airborne particulate matter. In contrast, the concentrations of two nitro-PAHs, 2-nitrofluoranthene and 2-nitropyrene, remained the same. These nitro-PAHs are known to be formed by atmospheric nitration of their parent PAHs, and this result suggested factors other than the concentration of parent PAHs and $NO_2$ affects the degree of atmospheric formation of nitro-PAHs.

• Tribology and Lubricants
• /
• v.25 no.6
• /
• pp.387-398
• /
• 2009

The operation condition of recently designed pistons for high power and high speed diesel engine become more severe due to the increment of combustion pressure and temperature. So, in order to overcome high temperature, the application of the mono-metal cast aluminum alloy piston featuring an enclosed cast-in open cooling gallery has increased. In this research, it is developed a PCJ (piston cooling jet) rig tester, described the test procedure and validated the performance of sample piston cooling gallery design. Then the test rig will be used for developing the design technology of piston cooling gallery. The test rig is composed with oil reservoir and pumping system, oil jet system, piston fixing and moving system, collecting oil measuring system, and data measuring and recording system. It will be measured collecting efficiencies under conditions of a few piston positions, oil jet pressures and oil viscosities for a piston cooling gallery. Furthermore, the PCJ rig tester will be used for the optimum design of the oil cooling gallery which being applied to increase the cooling efficiency of pistons in diesel engines satisfying the EURO V emission regulation and the more.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2018.10a
• /
• pp.114-114
• /
• 2018

Among the various volatile organic compounds (VOCs) emitted by the plant, floral scent plays a key role in attracting pollinators for reproduction and mediates ecological interactions. Floral scent is an important trait and industry drives the competition for flowers with novel scents. Chrysanthemum is one of the well-known ornamental plants and is a popular cut flower across the world. Floral scent and the genes responsible for the floral scent emission are poorly studied in chrysanthemum. In the present study, floral scent and the expression pattern of floral scent genes were analyzed in two chrysanthemum cultivars 'Golden Egg' and 'Gaya Glory'. Initially, intensity of the floral scent in five developing stages of flower including 'budding (B), bud developing (BD), initial blooming (IB), almost open (AO) and open flower (OF)' was analyzed using electronic nose (E-nose) with six metal oxide sensors. Based on the distance analysis, different stages of flower showed different relative intensity of scent according to the sensory evaluation. Although the scent pattern differed by stage, scent intensity was strongest in the OF stage in the completely opened flower in both the cultivars. Further, expression pattern of six genes in the floral scent pathway including FDS, IDI, ISPH, TPS2, TPS5 and TPS6 was observed in all the five stages of the flower in both the cultivars. The expression pattern of all the six genes differed by stage and the terpene synthase genes TPS2, TPS5 and TPS6 showed good expression levels in the $5^{th}$ flower stage compared to other stages. This study provides a preliminary data for understanding the regulation of floral scent in chrysanthemum.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.2
• /
• pp.123-132
• /
• 2014

The maritime sector is advancing with dedicated endeavor to reduce greenhouse gas in addressing issues with regards to global warming. Since 01 January 2013, the International Maritime Organization (IMO) regulation mandatory requirement for Energy Efficiency Design Index (EEDI) has been in place and should be satisfied by newly-built ships of more than 400 gross tonnage and the Ship Energy Efficiency Management Plan (SEEMP) for all ships type. Therefore, compliance to this necessitates planning during the design stage whereas verification can be carried-out through an acceptable method during sea trial. The MEPC-approved 2013 guidance, ISO 15016 and ISO 19019 on EEDI serves the purpose for calculation and verification of attained EEDI value. Individual ships EEDI value should be lower than the required value set by these regulations. The key factors for EEDI verification are power and speed assessment and their synchronization. The shaft power can be measured by telemeter system using strain gage during sea trial. However, calibration of shaft power onboard condition is complicated. Hence, it relies only on proficient technology that operates within the permitted ISO allowance. On the other hand, the ship speed can be measured and calibrated by differential ground positioning system (DGPS). An actual test on a newly-built vessel was carried out to assess the correlation of power and speed. The Energy-efficiency Design Index or Operational Indicator Monitoring System (EDiMS) software developed by the Dynamics Laboratory-Mokpo Maritime University (DL-MMU) and Green Marine Equipment RIS Center (GMERC) of Mokpo Maritime University was utilized for this investigation. In addition, the software can continuously monitor air emission and is a useful tool for inventory and ship energy management plan. This paper introduces the synchronization and identification method between shaft power and ship speed for EEDI verification in accordance with the ISO guidance.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.423-429
• /
• 2012

Miller cycle is considered as an effective means to meet the regulation on Tier II and to reduce $CO_2$ emission. For this cycle, the amount of intake air supplied should be enough increased. Therefore, the intake system with minimized resistance for air flow is under consideration. In this study, the flow coefficients of intake valves were measured in order to obtain the basic data for the cycle simulation and intake port design. The flow coefficients were measured using the steady-flow test rig. As a test result for the poppet valve used the marine engine with medium speed, the flow coefficients are increased to about 0.62 with the valve lift. In addition it is confirmed that the flow coefficients have the characteristic value irrelevant to the S/B ratio.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.7
• /
• pp.905-910
• /
• 2010

Exhaust manifolds are the first structures to be developed by hydroforming; mass production of exhaust manifolds by this method will be possible soon. This is obviously related with tight emission regulation induced by environmental problems commonly for both domestic and worldwide and standards, thus evoking its solution for domestic automakers. Compared to conventional cast products, thin-gauge tubular hydroformed exhaust manifold have superior features; for example, in the hydroformed exhaust manifold, gas decomposition during the cold-start period of the engine is reduced by lowering the heat sink, and manufacturing process is simplified since less welding is involved. The aim of this study is to develop a hydroformed exhaust manifold; the study deals with the components, the hydroforming process, and tool design of the manifolds. The performance of the exhaust system is evaluated by performing flow analysis, heat-transfer analysis, heat-stress analysis, and fatigue analysis by using a computer.

• Safety and Health at Work
• /
• v.10 no.4
• /
• pp.518-526
• /
• 2019

Background: Additive manufacturing (AM) is a rapidly expanding new technology involving challenges to occupational health. Here, metal exposure in an AM facility with large-scale metallic component production was investigated during two consecutive years with preventive actions in between. Methods: Gravimetric analyzes measured airborne particle concentrations, and filters were analyzed for metal content. In addition, concentrations of airborne particles <300 nm were investigated. Particles from recycled powder were characterized. Biomonitoring of urine and dermal contamination among AM operators, office personnel, and welders was performed. Results: Total and inhalable dust levels were almost all below occupational exposure limits, but inductively coupled plasma mass spectrometry showed that AM operators had a significant increase in cobalt exposure compared with welders. Airborne particle concentrations (<300 nm) showed transient peaks in the AM facility but were lower than those of the welding facility. Particle characterization of recycled powder showed fragmentation and condensates enriched in volatile metals. Biomonitoring showed a nonsignificant increase in the level of metals in urine in AM operators. Dermal cobalt and a trend for increasing urine metals during Workweek Year 1, but not in Year 2, indicated reduced exposure after preventive actions. Conclusion: Gravimetric analyses showed low total and inhalable dust exposure in AM operators. However, transient emission of smaller particles constitutes exposure risks. Preventive actions implemented by the company reduced the workers' metal exposure despite unchanged emissions of particles, indicating a need for careful design and regulation of the AM environments. It also emphasizes the need for relevant exposure markers and biomonitoring of health risks.

• Journal of Power System Engineering
• /
• v.20 no.6
• /
• pp.93-98
• /
• 2016

Environmental problems are issued throughout all over the world and which are needed the strength management. In case of the diesel cars are also being developing and studying continuously about various after-treatments device such as EGR, LNT, SCR, DPF and DOC etc. which are used for decreasing $NO_X$ and PM. The air temperature goes up to $39^{\circ}C$ in summer and goes down to $-20^{\circ}C$ in winter because of the location. These changing of the temperature can effect to the engine and harmful exhaust gas discharged and it seems to make the increase - decrease different. The result of the evaluate while changing between the test-mode and the air temperature, which expresses that WLTC-mode is 2.2 times and FTP_75 mode is 4.1~6 times increase to the comparison NEDC-mode of the current regulation. The exhaust characteristic of $NO_X$ by the changing temperature increases in the low temperature and 4.3 times in $14^{\circ}C$ and 21.3 times in $-7^{\circ}C$ with maximum when it compares to $23^{\circ}C$. The fuel efficiency of the different weight car and engine with same data is about 5.7 % in maximum.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1193-1200
• /
• 2001

There are many regulation test methods to be related with engine emissions such as CVS-75, D-13, ECE-15 modes and so on. Most of these modes are consisted of lots of transient conditions that have rapid acceleration, deceleration and cranking modes. In this experimental research, the engine characteristics of cranking, accelerating and power output in a S.I. engine were studied to compare with neat gasoline and alternative fuels of M30 (methanol 30%, aromatic series 32%, non-aromatic 38%) and M50 (methanol 50%, aromatic 30%, non-aromatic 20%) for performance and exhaust emissions. The results show that reformulated methanol fuels are better emissions reduction of 15.7% over than that of neat gasoline fuel especially in HC and CO emissions at cranking mode. And the accelerating performances coincide with the results of distillation curve. CO concentration for M50 fuel is varied in a just little for the condition of slow acceleration. At wide-open throttle condition, brake specific energy consumption of reformulated fuels is increased and thermal efficiency is some what lower than that of gasoline fuel.