• Journal of Energy Engineering
• /
• v.18 no.3
• /
• pp.169-174
• /
• 2009

In the study, the effect of the ultrasonic energy in transportational diesel fuel on the engine performance and exhaust emission has been investigated for indirect injection diesel engine. It was tested to estimated change of engine performance and exhaust emission characteristics for the transportational diesel fuels and the reforming fuels which was irradiated by the ultrasonic energy. The results of the study may be concluded as follows; By the irradiation of ultrasonic energy on the diesel fuel, cylinder pressure, heat release rate and engine power were increased but bsfc, mass fraction burned, and smoke were reduced. Also, the combustion was more stabilized and became complete and NOx was increased.

• Korean Journal of Organic Agriculture
• /
• v.13 no.2
• /
• pp.185-195
• /
• 2005

Two hundred [(Duroc${\times}$Yorkshire)${\times}$Landrace] pigs were used in a 117-d growth assay (including four growth stages) to determine the effects of dietary supplementation of Lactobacillus reuteri on performance of swine, fecal and rectumal microflora and carcass grade. Pig diet was divided tow types, commercial diet (Control group) and supplemention of 0.1% Lactobacillus reuteri (Treatmental group). There was tend to increased in average daily gain (ADG) and feed efficiency (Feed/gain) in treatmental group than control group during the whole experimental period. The number of Lactobacilius spp. into rectum and feaces and carcass rate tended to increase in treatmental group than control group. Ammonia emission from excreta were decrease by supplemention of 0.1% Lactobacillus reuteri in feed (P<0.05). These results indicated that the dietary Lactobacillus reuteri were effective in performance, increasing of Lactobacilius spp. into rectum and feaces, decreasing ammonia emission from excreta, and it had also effective the carcass rate in swine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.144-152
• /
• 2006

Split injection has been known to reduce total hydrocarbon (THC) emission level and increase engine performance under certain operating conditions 1, 2). Exhaust Gas Recirculation (EGR) is a common technique adopted for nirtric oxides (NOx) reduction by the dilution of intake air, despite a sacrifice of simultaneous increase in THC and decrease in engine performance3). Thus, using split injection with adequate EGR may improve the emission level of UBHC, NOx and the engine performance compared to that of single-injection with or without EGR cases. The purpose of this study is to investigate the engine performance and emission levels at various engine operating conditions and injection methods when it is applied with EGR. The characteristics of single-injection and split-injection were investigated with various engine loads and EGR rates. The engine speed is changed from 800rpm to 1200rpm to investigate how the combustion characteristics are changing with increasing engine speed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.135-144
• /
• 2005

The Effects of intake swirl and combustion parameters on the performance and emission characteristics in a V8 type turbocharged intercooler D.I. diesel engine of the displacement $16.7\iota$ were studied experimentally in this paper. Generally the swirl in the combustion process of diesel engine promotes mixing of the injection fuel and the intake air. Also, TCI diesel engine is put to practically use intercooler in order to increase boost efficiency which is cooled boost air. As a result of steady flow test, when the swirl ratio is increased, the mean flow coefficient is decreased, whereas the Gulf factor is increased. And through engine test, its can be effected to meet performance and emission by optimizing the main parameters; the swirl ratio is 2.25, compression ratio is 17.5, combustion bowl is re-entrant $8.5^{\circ}$, nozzle hole diameter is $\phi0.33^{\ast}3+\phi0.35^{\ast}2$, injection timing is BTDC $12^{\circ}CA$ and turbocharger is T02 model which are compressor 0.6A/R+46trim and turbine 1.0A/R+57trim.

• Journal of Energy Engineering
• /
• v.21 no.3
• /
• pp.272-279
• /
• 2012

The emission quota of 26.9% was allocated to the architectural sector according to the greenhouse gas(GHG) emission reduction goal of the government. It has become inevitable to change the architectural structures in a low-energy consumption and sustainable manner for new and existing house. The introduction of various legal systems and deregulation have been attempted to promote the low carbon emission and sustainable energy conversion. Although overall emission reduction goal has been set for 6.7 million units of existing houses, there has been a lack of standards and directions for the emission reduction measures. This study was intended to present the most economic and effective green technology improvement measures based on the investigation into the current conditions through direct visit to the selected architectural structures and the repeated simulation of relevant technical elements.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.1
• /
• pp.64-68
• /
• 2016

High Temperature Superconductor power cable systems are being developed actively to solve the problem of increasing power demand. With increases in the unit length of the High Temperature Superconductor power cable, it is necessary to develop highly efficient and reliable cryogenic pumps to transport the coolant over long distances. Generally, to obtain a high degree of efficiency, the cryogenic pump requires a high pressure rise with a low flow rate, and a partial emission type pump is appropriate considering its low specific speed, which is different from the conventional centrifugal type, full emission type. This paper describes the design of a partial emission pump to circulate subcooled liquid nitrogen. It consists of an impeller, a circular case and a diffuser. The conventional pump and the partial emission pump have different features in the impeller and the discharge flow passage. The partial emission pump uses an impeller with straight radial blades. The emission of working fluid does not occur continuously from all of the impeller channels, and the diffuser allows the flow only from a part of the impeller channels. As the area of the diffuser increases gradually, it converts the dynamic pressure into static pressure while minimizing the loss of total pressure. We used the known numerical method for the optimum design process and made a CFD analysis to verify the theoretical performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• Journal of ILASS-Korea
• /
• v.1 no.2
• /
• pp.50-56
• /
• 1996

In an fuel injection type gasoline engine, atomization of fuel droplet and mixture formation process are very important to understand engine combustion efficiency, and also has influence directly on the decision of engine performance and pollutant emission. In this study, perforated throttle valve instead of solid type throttle valve was developed and equipped to an SPI engine to promote secondary atomization and good droplet-air mixture formation. From the engine performance lest. it was verified that the case of perforated valve kas more advantages in each experimental parameters such as in cylinder gas pressure, mass burnt ratio, fuel consumption rate, and pollutant emission characteristics than that of solid one equipped. No matter what the same perforated valve, there are some distinct results in engine performance characteristics according to the perforate ratio.

• Journal of ILASS-Korea
• /
• v.6 no.3
• /
• pp.32-37
• /
• 2001

The characteristics of engine performance with fuel injection system in D.I. diesel engine were studied in this paper. A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozzle hole, diameters of an injection pipe and injection timing in the fuel injection system. The authors have obtained the results that optimizing the factors of fuel injection system is significant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.192-198
• /
• 2005

Recently, Automobile manufacturers regarding stability, economic environmental-friendly problems by the development of automobile. This reason is increasingly strict environmental regulations to lower fuel consumption and reduce emission. Designing more efficient and low emission control exhaust system results in more efficient Performance, reduced back Pressure and higher convert efficiency. Also to reduce the noise and the vibration of the automobile. According to develop variable type muffler, dual muffler and active intelligence exhaust system unit. Improvement in engine performance and fuel consumption rate, higher conversion efficiency demand information of pressure fraction and heat characteristics. To be able to determine these factor fur we experiment on each case of exhaust system unit. In this study, how back pressure is distributed in flow-through in exhaust system and how to design exhaust system flexibleness, efficiency, lower back pressure and optimal performance. This study furnish basic data for engineers, technicians.