• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.4
• /
• pp.205-211
• /
• 2001

The characteristics of super duplex stainless steel were investigated on its fibrous structure and dispersed structure. These structures consist of various volume fractions and distributions of the austenite phase that were obtained by changing the heat treatment temperature and cycle. The fibrous structure had higher austenite volume fraction than dispersed structure on the same temperature. As the austenite volume fraction increased in both structures, tensile strength and elongation increased, but hardness decreased. Fatigue life of fibrous structure parallel to rolling direction was shorter than that of perpendicular to rolling direction. Fatigue life of dispersed structure was longer than parallel fibrous structure, and shorter than perpendicular fibrous structure. Fatigue crack propagation rate of fibrous structure was faster than that of dispersed structure.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.6
• /
• pp.327-337
• /
• 2011

Effects of microstructural change, tensile properties and impact property according to the change of austenitizing temperature and tempering temperature of AISI 51B20 steel were examined. Regardless of austenite grain size, lath martensite with needle and packet shapes was found at tempering temperature of $300^{\circ}C{\sim}400^{\circ}C$. The needles of lath martensite changed to parallel packet at tempering temperature of $450^{\circ}C{\sim}600^{\circ}C$. As tempering temperature increased, tensile strength, yield strength and hardness decreased, while elongation, ratio of reduction area and Charpy impact energy increased. Grain size increased when quenching temperature was $930^{\circ}C$. Grain size had prominent effect on the mechanical properties of AISI 51B20 steel. Ratio of tensile strength/yield strength and yield strength autenitized at $880^{\circ}C$ followed by tempering at $350^{\circ}C{\sim}450^{\circ}C$ showed higher values than that of autenization at $930^{\circ}C$ due to fine grain size.

• Elastomers and Composites
• /
• v.32 no.5
• /
• pp.295-301
• /
• 1997

The effects of filler types and compositions on the final properties such as tensile strength, % elongation, hardness, and specific gravity of chloroprene rubber were investigated. The fillers involved in this investigation were HAF-type carbon black, Mistron, and white clay, For each filler, the variation of filler compositions gave almost the linear effects on the all properties investigated. For a fixed filler composition, different filler types gave different influential strength on rubber properties. After linearlization of experimental data with respect to each filler composition, the simple linear addition of each property with respect to filler compositions was applied to predict the final properties of the filler included rubber systems. For the chloroprene rubber system including the fillers composed of Mistron(25phr)/HAF(20phr)/clay(35phr), the predicted properties were well in accordance with the experimental results. Similar results were obtained for other additives such as processing oil and accelerator.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.523-527
• /
• 2008

In this study, mechanical properties of Alloy 718 welded after forgings for jet propulsion component was investigated. Hot-forged and machined work-pieces($230mm\times70mm\times15mm$) which have different grain sizes are welded by electron beam welding technique. After welding, the components were solution heat-treated and aged. Samples were sectioned to analyze the microstructural evolution and formation of micro-crack. It was found that HAZ grain boundary liquation crack generally initiates in the coarse grains rather than the fine grains. Needle-like phases with high Nb contents were found at the outer part near the base metal. Vickers hardness and tensile tests were carried out at room temperature and at $649^{\circ}C$. The tensile properties of electron beam welding specimens exhibited around 100MPa and 10% decrease in strength and elongation, respectively.

• Elastomers and Composites
• /
• v.52 no.2
• /
• pp.105-113
• /
• 2017

The curing behavior, mechanical properties, hot-air aging resistance, abrasion properties,thermal properties, etc., of EVM/EPM/APP (ammonium polyphosphate)/DPER (dipentaerythritol)/EG (expandable graphite) and EVM/EPM/ATH (aluminium trihydroxide) flame retarding systems in ethylene vinyl acetate rubber (EVM) blends with EPM (ethylene propylene rubber) were sequentially examined. For both flame retarding systems, the torque values increased with the content of EPM rubber and with the vulcanization time. As the content of EPM rubber increased, the scorch time became shorter, whereas the optimum cure time followed an increasing trend. For the EVM/EPM/APP/DPER/EG flameretarding system, as the content of EPM rubber increased, the hardness did not change,whereas the tensile strength and elongation at break decreased. A hot-air aging resistance test at $150^{\circ}C$ showed that the heat resistance decreased with the EPM content regardless of the kinds and contents of flame retardants. As the EPM content increased, the abrasion rate became higher and the abrasion resistance of the EVM/EPM/APP/DPER/EG flame retarding systems exceeded that of the EVM/EPM/ATH flame retarding counterparts. In comparison with the EVM/EPM/ATH flame retarding systems, the thermal stability of the EVM/EPM/APP/DPER/EG flame retarding system showed an increasing tendency.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.5
• /
• pp.299-304
• /
• 2004

Influence of Ca addition on microstructure and room temperature mechanical properties has been studied for AZ31(Mg-3%Al-1%Zn-0.2%Mn)-(0~0.5)%Ca wrought alloys, based on experimental results from metallography, X-ray diffractometry and mechanical tests. Yield strength, ultimate tensile strength and hardness of the alloys increased remarkably with increasing Ca content, whereas elongation was deteriorated continuously. Microstructural examination revealed that Ca addition efficiently refined grains of ${\alpha}$(Mg) phase and that some of the Ca dissolved in ${\beta}(Mg_{17}Al_{12})$ precipitates. The former and the latter facts are thought to be responsible for improved strength and loss of ductility of the AZ31+Ca wrought alloys, respectively.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.114-116
• /
• 2005

There are some problems when weld gray cast iron which is used well in automobile industry with auto MIG welding. the problems are followed like this 1) Occurrence of porosity and hardening organization. 2) Occurrence of crack due to lower elongation of gray cast iron when restraint stress works on. 3) Occurrence of porosity and unstable bead shape due to unstable arc under low current MIG welding.. especially there is a restraint on chemical composition of weld metal because the weldment demands more than 570Hv hardness. so it is hard to use Fe-Ni wire to prevent cracks occured on weldment and new welding method is needed to resolve that problems. This study shows how to prevent porosity and cracks occurring when weld gray cast iron trimming die and shows a new welding method for press die of gray cast iron

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.2
• /
• pp.126-130
• /
• 2015

In this study, some materials are organized and experimented with variables to obtain the optimum mix proportion for the mechanical property of halogen free flame resistance compound with varying addition of nano clay. Tensile strength, density and stiffness are tested in the room temperature. In this study, unlike existing layered structure, nano clay with tabular structure is used and sufficient stiffness, strength, thermal stability and gas block capability can be achieved with small amount of addition. Tensile strength and elongation test show high rupture strength only in specimens with compatibilizing agents while density test shows average measurement in all the specimens except T-9. It was confirmed that the measurement value according to the additives in compatibilizing agent or in nano clay of hardness test represents similarly.

• Journal of Adhesion and Interface
• /
• v.18 no.4
• /
• pp.159-165
• /
• 2017

In this study, we synthesized UV-curable urethane acrylates with different contents of BA, reactive diluent and characterized their physical properties such as thermal, mechanical properties, adhesive strength and flexibility resistance. From a result of DSC, Tg of polyol and acrylate resin were separated as the BA content increased more than 40%. Also, tensile strength, elongation and adhesive strength decreased with increasing the BA content. The UV-curable urethane acrylate with 40% BA has shown good flexibility resistance compared to other resin due to poor hardness and Tm of acrylate resin.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.69-74
• /
• 1999

The microstructure of the reagion of carters, created by Cu and W-Cu shaped charge jets, in a 1020 mild steel target has been intestiaged. The region ahead of the crater created by the Cu shaped charge jet, reveals dramatic grain refinement implying the occurrence of a dynamic recrystallization, while that of W-Cu one dose a martensitic transformation indicative of heating up to an austenitic region followed by rapid cooling.The impacting pressure calculated when the W-Cu shaped charge jet encounters the target is higher than that of the Cu one. The micro-hardness of the region ahead of the crater created by the W-Cu shaped charge jet is also higher than that of the Cu one. The microstructure of W-Cu slug remained in the inside of the craters depicts the occurrence of the remarkable elongation of W particles during the liner collaphse. From these results, the microstructural variation of the region ahead of the crater with Cu and W-Cu shaped charge jets is discussed in trems of the pressure dependency of the transformation region of ferrite and austenite phases.