• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.1
• /
• pp.89-98
• /
• 2002

Optical current sensor and optical voltage sensor modules were designed and fabricated to improve measurement error and insulation in automatic power distributor By using Faraday effect, optical current sensor with an $\alpha$-iron core was designed and fabricated to minimize current induction of the other phase and was optimized to maintain linearity. Optical voltage sensor was fabricated owing to the pockets effect and adopted spatial electric field type because of small room in an automatic power distributor. To connect a distributor with an external terminal for signal processing, optical multi connector was designed, fabricated and tested for coupling loss and gas leakage. The linearity of optical current sensor for applied current maintains variation of smaller than 2.5% for applied current range from 20A to 700A. The linearity of optical voltage sensor was smaller than 1% for appling voltage from 6.6kV to 19.8kV. Since the measured characteristics are good, these devices can be considered as being applicable in practice.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.430-436
• /
• 2006

Polarization-independent $Ti:LiNbO_3\;2{\times}2$ optical add/drop multiplexer for the 1550nm wavelength region is fabricated. The device consists of two input waveguides, two polarization beam splitters. two polarization conversion/electrooptic tuning waveguide sections, and two output waveguides. The single mode channel waveguides for both TE and TM polarizations are fabricated on a x-cut $Ti:LiNbO_3$substrate by Ti diffusion. Spectral section is based on phase-matched polarization conversion due to shear strain induced by a thick $SiO_2$ grating overlay film. An applied voltage tunes the device by changing the waveguide birefringence, hence the optical wavelength at which most efficient polarization conversion occurs. Tuning rate of 0.094nm/V with a maximum range of 17nm has been obtained. The nearest side-lobe is about 8.2dB. The FWHM is 3.72nm.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.128-134
• /
• 2012

The performance evaluation and fabrication of integrated-optic electric-field sensor utilizing $Ti:LiNbO_3$ asymmetric Mach-Zehnder intensity modulator with a push-pull lumped electrode and a plate-type probe antenna to measure an electric field strength is described. The modulator has a small device size of $46{\times}7{\times}1\;mm$ and operates at a wavelength $1.3{\mu}m$. The devices are simulated based on the BPM software and fabricated utilizing Ti-diffused $LiNbO_3$ channel optical waveguides. The minimum detectable electric field is 1.02 V/m and 6.91 V/m, corresponding to a dynamic range of ~35 dB and ~10 dB at the frequencies of 500 KHz and 5 MHz, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.29-35
• /
• 2016

We have demonstrated a $Ti:LiNbO_3$ electro-optic electric-field sensors utilizing a $1{\times}2$ Y-fed balanced-bridge Mach-Zehnder interferometric (YBB-MZI) modulator which uses a 3-dB directional coupler at the output and dipole patch antenna. The operation and design were proved by the BPM simulation. A dc switching voltage of ~16.6 V and an extinction ratio of ~14.7 dB are observed at a wavelength of $1.3{\mu}m$. For a 20 dBm rf power, the minimum detectable electric-fields are ~1.12 V/m and ~3.3 V/m corresponding to a dynamic range of about ~22 dB and ~18 dB at frequencies 10 MHz and 50 MHz, respectively. The sensors exhibit almost linear response for the applied electric-field intensity from 0.29 V/m to 29.8 V/m.

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.469-475
• /
• 2005

An integrated photonic microwave bandpass filter has been proposed and demonstrated incorporating a coherently coupled microring resonator in low-loss polymers. The proposed device may feature compact site, simple structure, tuning via the thermooptic and electrooptic effect, and flexible integration with other electrical and optical devices. The resonator was designed to have an extremely small bandwidth so that it could be used to selectively pass the optical signal carrying the microwave signal to attain efficient bandpass filtering. We made and tested two resonators with a single ring and double rings, and performed a theoretical fitting of their measured transfer curves to predict the performance of the microwave filters based on them precisely. It was found that as the number of the rings used for the resonator increases, the bandwidth gets smaller, the rolloff sharper, and the band rejection higher. Finally our filter exhibited the center frequency of 10GHz, the 3-dB bandwidth of 1.0GHz, the corresponding quality (Q) factor of 10, and the rejection outside of the passband of more than 25dB.