• 대한전자공학회논문지SD
• /
• 제46권8호
• /
• pp.31-40
• /
• 2009

본 논문은 SoC 전원 관리를 위한 고성능 DC-DC 부스트 변환기 설계에 관한 것이다. DC-DC 변환기에서 일반적으로 전하 축전용으로 사용되는 인덕터와 커패시터를 칩 안에 집적하기 위해 그 크기를 크게 감소시키고, 스위칭 주파수를 100MHz로 하였다. 고속 동작에서 전압 방식의 제어를 선택하여 신뢰성을 높였으며 적절한 주파수 보상으로 안정적인 동작 특성을 확보하였다. 설계한 DC-DC 변환기는 thick gate oxide 옵션이 포함된 0.18${\mu}m$ CMOS 표준 공정으로 제작하였다. 내부 필터 커패시터를 포함한 칩의 면적은 8.1$mm^2$ 이고, 제어기가 차지하는 면적은 1.15$mm^2$ 이다. 부하 전류 300mA 이상에 대하여 4V의 출력을 얻는 변환기의 최대 효율은 76% 이상, load regulation은 100mA의 변화에 대하여 0.012% (0.5mV) 의 특성을 갖는다.

• 한국전자통신학회논문지
• /
• 제6권6호
• /
• pp.855-864
• /
• 2011

본 논문은 IPMSM(Interior Permanent Magnet Synchronous Motor)의 고성능 운전을 위해 비선형 제어를 기반으로 하는 적응 백스텝핑 제어기를 제안한다. 먼저 각속도의 추종성능을 향상시키기 위해서 비선형 백스텝핑 제어기를 설계한다. 파라메타 변동의 영향을 고려하지 않고 설계된 제어기는 고성능 운전이 어렵다. 부하토크의 변동에 대해 실시간 적응할 수 있는 파라메타 추정기를 설계에 포함하여 고성능 운전이 가능하게 한다. 또한 전동기의 효율적인 전력소비를 위하여 최대토크를 얻기 위한 최소전류의 운전을 할 수 있도록 제어기를 설계하였다. 제안된 제어기로 2마력급의 IPMSM에 적용하여 각속도 레퍼런스에 대한 추종성능과 부하토크 변동에 대한 추정, 그리고 MTPA(Maximum Torque per Ampere) 운전을 시험하여 일정토크 운전영역에서 안정화된 강건한 제어기임을 시뮬레이션을 통해 확인할 수 있었다.

• 한국전자통신학회논문지
• /
• 제13권1호
• /
• pp.93-100
• /
• 2018

본 연구는 정밀한 각속도 추종을 위해 토크오차를 보상하는 제어기와 구현에서 제어기의 안정성을 보완하는 방법을 제안한다. 또한 설계된 제어기가 점근적인 안정할 수 있음을 리아프노프 안정도이론에 근거하여 증명하였다. 제안된 제어기는 d축 기준전류를 임의 값에 대한 제어가 가능하고, 속도이득과 전류이득의 두 가지로 손쉽게 제어성능을 달성할 수 있도록 하였다. 약 750W급의 IPMSM에 적용한 결과 레퍼런스 속도 1200[RPM]에 대한 정상상태 오차는 0.1[%]이내이며, 약 5[Nm]의 상수부하에서 약 0.2초 이내에 외란을 극복하여 점근적인 안정한 제어기임을 확인 할 수 있다.

• 제어로봇시스템학회논문지
• /
• 제18권6호
• /
• pp.519-525
• /
• 2012

Electric brake booster systems replace conventional pneumatic brake boosters with electric motors and rotary-todisplacement mechanisms including ECU (Electronic Control Unit). Electric booster brake systems require precise target pressure tracking and control robustness because vehicle brake systems operate properly given the large range of loading and temperature, actuator saturation, load-dependent friction. Also for the implement of imbedded control system, the controller should be selected considering the limited memory size and the cycle time problem of real brake ECU. In this study, based on these requirements, a sliding mode controller has been chosen and applied considering both model uncertainty and external disturbance. A mathematical model for the electric booster is derived and simulated. The developed sliding mode controller considering chattering problem has been compared with a conventional cascade PID controller. The effectiveness of the controller is demonstrated in some braking cases.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제10권2호
• /
• pp.113-118
• /
• 2010

This paper proposed an ECAM (Electronic cam) control system which has simple and general structure. The proposed cam controller adopted the linear and polynomial curve-fitting method to generates a smooth cam profile curve function. Smooth motion trajectory of master actuator guarantees the good performance of slave motion and has an important effect on the interpolation quality of ECAM. The auto-tuning PID velocity controller was applied to overcome the uncertainties in ECAM, and the gains of the controller are updated continuously to ensure the consistency of system performance under varying working conditions. The robustness of system against the varying load torque disturbances and noises is guaranteed by using the load torque disturbance observer to suppress the disturbance on master actuator. The velocity compensator was applied to compensate the degradation of performance of slave motion caused from the varying driving speed of master motion. The stability and validity of the proposed ECAM control system was verified by simulation results.

• Journal of Electrical Engineering and Technology
• /
• 제4권2호
• /
• pp.211-218
• /
• 2009

This paper presents a voltage and frequency controller (VFC) for a 4-wire stand-alone wind energy conversion system (WECS) employing an asynchronous generator. The proposed VF con-troller consists of a three leg IGBT (Insulated Gate Bipolar Junction Transistor) based voltage source converter and a battery at its DC bus. The neutral terminal for the consumer loads is created using a T-connected transformer, which consists of only two single phase transformers. The control algorithm of the VF controller is developed for the bidirectional flow capability of the active power and reactive power control by which it controls the WECS voltage and frequency under different dynamic conditions, such as varying consumer loads and varying wind speeds. The WECS is modeled and simulated in MATLAB using Simulink and PSB toolboxes. Extensive results are presented to demonstrate the capability of the VF controller as a harmonic eliminator, a load balancer, a neutral current compensator as well as a voltage and frequency controller.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.451-459
• /
• 2018

This work presents an approach for modeling of electric vehicle considering the vehicle dynamics, drive train, rotational wheel and load dynamics. The system is composed of IPMSM (Interior Permanent Magnet Synchronous Motor) coupled with the wheels through a drive train. Generally, IPMSM is controlled by ordinary PID controllers. Performance of the ordinary PID controller is not satisfactory owing to the difficulties of optimal gain selections. To overcome this problem, a new type of fuzzy logic gain tuner for PID controllers of IPMSM is required. Therefore, in this paper fuzzy logic based gain tuning method for PID controller is proposed and compared with some previous control techniques for the better performance of electric vehicle with an optimal balance of acceleration, speed, travelling range, improved controller quality and response. The model was developed in MATLAB/Simulink, simulations were carried out and results were observed. The simulation results have proved that the proposed control system works well to remove the transient oscillations and assure better system response in all conditions.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.158-161
• /
• 1987

The characteristic of a control system is apt to be changed by load condition. This paper getting more optimal environment and the algorithm for parameter by itself In PID control system with microprocessor.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1869-1883
• /
• 2016

In recent years, some converter structures and analyzing methods for the voltage regulation of stand-alone self-excited induction generators (SEIGs) have been introduced. However, all of them are concerned with the three-phase voltage control of three-phase SEIGs or the single-phase voltage control of single-phase SEIGs for the operation of these machines under balanced load conditions. In this paper, each phase voltage is controlled separately through separated converters, which consist of a full-bridge diode rectifier and one-IGBT. For this purpose, the principle of the electronic load controllers supported by fuzzy logic is employed in the two-different proposed converter structures. While changing single phase consumer loads that are independent from each other, the output voltages of the generator are controlled independently by three-number of separated electronic load controllers (SELCs) in two different mode operations. The aim is to obtain a rated power from the SEIG via the switching of the dump loads to be the complement of consumer load variations. The transient and steady state behaviors of the whole system are investigated by simulation studies from the point of getting the design parameters, and experiments are carried out for validation of the results. The results illustrate that the proposed SELC system is capable of coping with independent consumer load variations to keep output voltage at a desired value for each phase. It is also available for unbalanced consumer load conditions. In addition, it is concluded that the proposed converter without a filter capacitor has less harmonics on the currents.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.323-325
• /
• 1996

The design of Intelligent Energy Saving Power System Controller (IESPSC) for Telecom DC power plants is proposed and presented in this paper. From the past experience. rectifiers for Telecom DC power plants have been operated inefficiently at light loads. IESPSC offers "novel load sharing" approach based on the knowledge of each unit's efficiency of paralleled rectifiers. Neural networks is used for identifying each rectifier's efficiency characteristic curve corresponding to load currents, which is in turn utilized to produce a system efficiency close to the maximum under all operating conditions. In addition, by limiting the number of operating units to the minimum while maintaining high efficiency at the determined loads, a drastic savings in operating cost can be achieved.