• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.525-528
• /
• 2001

ZnO:Al thin film can be used as a transparent conducting oxide(TCO) which has low electric resistivity and high optical transmittance for the front electrode of amorphous silicon solar cells and display devices. This study of electrical, crystallographic and optical properties of Al doped ZnO thin films prepared by Facing Targets Sputtering (FTS), where strong internal magnets were contained in target holders to confine the plasma between the targets, is described. Optimal transmittance and resistivity was obtained by controlling flow rate of O$_2$ gas and substrate temperature. When the of gas rate of 0.3 and substrate temperature 200$^{\circ}C$ , ZnO:Al thin film had strongly oriented c-axis and lower resistivity(<10$\^$-4/Ω-cm).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.418-421
• /
• 2001

The ceramic filters were developed using technology similar to that of quartz crystal and electro- mechanical filter. However, the key to this development involved the theoretical analysis of vibration modes and material improvements of piezoelectric ceramics. The primary application of ceramic filters has been for consumer-market use. Accordingly, a major emphasis has involved mass production technology, leading to low-priced devices. A typical ceramic filter includes monolithic resonators and capacitors packaged in unique configurations. Nakazawa developed a double-mode resonator as two acoustically coupled single resonators. And he developed 10.7MHz crystal filters using multi-energy trapping mode of thickness shear vibration. He succeeded in realizing a two-pole band pass filter response without external inductance by splitting a dot electrode to creak coupled symmetric and anti- symmetric vibration modes. Accordingly, the simulation for ceramic (inter were important. So that, this paper were investigated the pass frequency of filter on the electrode length and thickness of ceramic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.312-315
• /
• 2001

Recently organic electroluminescent devices have been intensively investigated for using in full-color flat-panel display. Since the quantum efficiency of electrophosphorescent device decrease rapidly as the luminance increase, it is desirable to operate the electrophosphorescent display with active matrix rather than passive matrix. Here we report the study of driving electrophosphorescent diode with all organic thin film transistor(OTFT). The structure of electrophosphorescent diode is ITO/TPD/BCP:Ir(ppy)$_3$/BCP/Alq$_3$/Li:Al/Al. In OTFT, Polymer is used as an insulator and pentacene as an active layer. Detailed performance of the integrated device will be discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.127-129
• /
• 1994

For scale-down EEPROM, MONOS structures with the different thicknesses of gate insulators, are fabricated and the memory characteristics, such as swtching and retention characteristics are investigated. As a results, the devices with the top oxide of 20A thick were deteriorated in retentivity. However, 11V-programmable voltage for ΔV$\sub$FB/=4V and 10-year data retention were achieved in MONOS structure with the t7p oxide of 50 ${\AA}$ thick and nitride 45${\AA}$thick.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.116-119
• /
• 1997

In this paper A double-layer organic electroluminescent(EL) device was fabricated using a TPD(N,N'-dipheny] -N,N'-bis(3-methylphenyl)-[1,1'-biphenyl]-4.4'-diamine: aromatic diamine), as a hole-transport material and tris (8-hydroxy quinolinate) aluminum(Alq$_3$) as a an emiting material and its performance characteristics were investigated. structure of devices is ITO/TPD/Alq$_3$/Al. we have fabricated hole transport layer of two types. Doping material of Hole Transport material is Poly(methyl methacrylate)(PMMA) and PEI(Poly-Ether-Imide). Carrier injection from the electrodes to the doped PMMA and PEI layer through the dopants and concomitant electroluminescence from Alq$_3$were observed. Green emission with luminance of 40cd/m$^2$was achieved at a drive voltage of 30V

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.183-190
• /
• 2002

This paper presents an improved Zero Voltage/Zero Current Switching (ZVZCS) commutation cell with minimum additional components, which provides soft switching at both turn-on and turn-off of main and auxiliary switches as well as diodes in a PWM DC/DC converter. The proposed soft-switching technique is suitable for not only minority, but also majority carrier semiconductor devices. The auxiliary switch of the proposed ZVZCS commutation cell is in parallel with the main switch, and therefore, the main switch and the diode are free of currentstress. The operation principles of the proposed ZVZCS commutation cell are theoretically analyzed using the PWM boost converter topology as an example. The validity of the PWM boost converter topology with the proposed ZVZCS commutation cell is verified through theoretical analysis, simulation and experimental results.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.752-758
• /
• 1995

Red emitting CaS:Eu,S electroluminescent(EL) device prepared at 550.deg. C by an electron-beam evaporation technique, demonstrated luminance of 175cd/m$\^$2/ and efficiency of 0.311m/W with 3kHz drive. Luminance was increased with the increase of applied voltage and frequency. From the results of the PL spectrum and the EL spectrum, the CaS:Eu, S device showed emission peak near 640nm resulted from the transition of EU$\^$2+/ 4f$\^$6/5d.rarw.4f$\^$7/. The capacitance of the phosphor layer from the Sawyer-Tower circuit was 10.5nF/cm$\^$2/.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.372-377
• /
• 2003

To realize a high integrated flash memory utilizing SONOS memory devices, the NOR type ITC(one Transistor Cell) SONOS flash arrays are fabricated and characterized. This SONOS flash arrays with the common source lines are designed and fabricated by conventional 0.35$\mu\textrm{m}$ CMOS process. The thickness of ONO for memory cells is tunnel oxide of 34${\AA}$, nitride of 73${\AA}$ and blocking oxide of 34${\AA}$ . To investigate operating characteristics, CHEI(Channel Hot Electron Injection) method and bit line method are selected as the program and 4he erase operation, respectively. The disturbance characteristics ,according to the program/erase/read cycling are also examined. The degradation characteristics are investigated and then the reliability of SONOS flash memory is guaranteed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.435-440
• /
• 2003

The electron-atom collision studies have been essentially used for testing and developing suitable theories of the scattering and collision processes, and for providing a tool for obtaining detailed information on the structure of the target atoms and molecules and final collision products. And, the development of that has also been strongly motivated by the need for electron collision data in such fields as laser Physics and development, astrophysics, Plasma devices, upper atmospheric processes and radiation physics. The concept and the Principle of determination of the electron collision cross sections for atoms and molecules by using the present electron swarm method are explained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.647-655
• /
• 2003

Commonly used SAW duplexers have a difficulty on manufacture so that a transmission line is printed on the package or an LTCC multi-layer is needed because a quarter-wave transmission line which is a kind of an isolation network is applied to the SAW duplexers. In this study, new structures of one chip type SAW duplexers are proposed. In the proposed structure, Tx and Rx SAW ladder filters and isolation networks are located on a single 36LiTaO$_3$ piezoelectric substrate. The manufacture process is very simple than commonly used product. It is possible to improve tile performance by means of optimizing the micro-strip line lumped elements. It is easy to integrate and modulate with other surrounding components. The optimal design techniques can be applied to other kind of multi-port devices.