• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권9호
• /
• pp.476-483
• /
• 1999

In this paper, electromagnetic forces acting on the rotor surface of a BLDC motor for hard disk drive are calculated by the finite element field analysis. The frequency characteristics of torque ripple, local force and unbalanced magnetic force as a source of mechanical vibration area analyzed. Ring-type permanent magnets for the brushless DC motor are apt to have different magnetization levels at each pole because of the unbalanced air gap between the magnet surface and the magnetizer fixture during the multi-poles magnetizing process. This paper discusses the effect of the unsymmetric magnetization distribution in the permanent magnet on the brushless DC motor performances. As a result, the unbalanced magnetic force acting on the rotor surface and the torque ripple are examined for the motor with an unsymmetric magnetization distribution, and compared with those of an ideally symmetric motor.

• 제어로봇시스템학회논문지
• /
• 제8권6호
• /
• pp.445-454
• /
• 2002

Torque ripple control of brushless DC motors has been the persisting issue of the servo drive systems in which the speed fluctuation, vibration and acoustic noise should be minimized. In this paper, a novel approach to achieve the ripple-free torque control with maximum efficiency based on the d-q reference frame is presented and analyzed. The proposed approach can provide the optimized phase current waveforms over wide speed range incorporating cogging torque compensation without an access to the neutral point of the motor windings. Moreover, the undesirable errors caused by the assumptions such as 3 phase balance or symmetry of the phase back EMF between electrical cycles, which are related with the manufacturing imperfections, can be also eliminated. As a result, the proposed approach provides a simple and clear way to obtain the optimal motor excitation currents. A hysteresis current control system is employed to produce high-frequency electromagnetic torque ripples for compensation. The validity and applicability of the proposed control scheme to real situations are verified through the simulations and experimental results.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1956-1964
• /
• 2018

Since the stator winding of High-Speed Permanent Magnet Generator (HSPMG) has few winding turns and low inductance value, it is more prone to be influenced by harmonic current. Moreover, the operation efficiency and the torque stability of HSPMG will be greatly influenced by harmonic current. Taking a 117 kW, 60 000 rpm HSPMG as an example, in order to analyze the effects of harmonic current on HSPMG in this paper, the 2-D finite element electromagnetic field model of the generator was established and the correctness of the model was verified by testing the generator prototype. Based on the model, the losses and torque of the generator under different frequency harmonic current were studied. The change rules of the losses and torque were found out. Based on the analysis of the influence of the harmonic phase angle on torque ripple, it is found that the torque ripple could be weakened through changing the harmonic phase angle. Through the analysis of eddy current density in rotor, the change mechanism of the rotor eddy current loss was revealed. These conclusions can contribute to reduce harmonic loss, prevent demagnetization fault and optimize torque ripple of HSPMG used in distributed power supply system.

• KEPCO Journal on Electric Power and Energy
• /
• 제5권3호
• /
• pp.229-233
• /
• 2019

Large-scale High Temperature Superconducting (HTS) wind power generators suffer from high electromagnetic force and high torque due to their high current density and low rotational speed. Therefore, the torque and Lorentz force of HTS wind power generators should be carefully investigated. In this paper, we proposed a Performance Evaluation System (PES) to physically test the structural stability of HTS coils with high torque before fabricating the generator. The PES is composed of the part of a pole-pair of the HTS generator for estimating the characteristic of the HTS coil. The 10 MW HTS generator and PES were analyzed using a 3D finite element method software. The performance of the HTS coil was evaluated by comparing the magnetic field distributions, the output power, and torque values of the 10 MW HTS generator and the PES. The magnetic flux densities, output power, and torque values of the HTS coils in the PES were the same as a pole-pair of the 10 MW HTS generator. Therefore, the PES-based evaluation method proposed in this paper can be used to estimate the critical characteristics of the HTS generator under high magnetic field and high torque before manufacturing the HTS wind turbines. These results will be used effectively to research and manufacture large-scale HTS wind turbine generators.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1089-1090
• /
• 2010

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1995년도 춘계연구발표회 논문개요집
• /
• pp.22-23
• /
• 1995

• 전기학회논문지
• /
• 제62권11호
• /
• pp.1535-1540
• /
• 2013

In this paper, the Radial Magnetic Force(RMF) and cogging torque which cause vibration and noise in IPM type BLDC motor were analyzed. The cogging torque and RMF cause electromagnetic vibration. So, a notch was installed for the equilibrium of RMF and cogging torque reduction. The notch was analyzed by using a Fourier Series for the energy distribution of the air-gap. The equilibrium of RMF and the reduction of cogging torque were performed by a Design Of Experiment(DOE) with the notch. Also, operating characteristics and efficiency were analyzed and compared.

• 전기학회논문지P
• /
• 제55권3호
• /
• pp.133-140
• /
• 2006

This paper is proposed an efficiency optimization control algorithm for a synchronous reluctance motor(SynRM) which minimizes the copper and iron losses. Also, this paper presents a speed estimated control scheme of SynRM using artificial neural network(ANN). There exists a variety of combinations of d and q-axis current which provide a specific motor torque. The objective of the efficiency optimization controller is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. It is shown that the current components which directly govern the torque production have been very well regulated by the efficiency optimization control scheme. The proposed algorithm allows the electromagnetic losses in variable speed and torque drives to be reduced while keeping good torque control dynamics. The control performance of ANN is evaluated by analysis for various operating conditions. Analysis results are presented to show the validity of the proposed algorithm.

• 전기학회논문지
• /
• 제64권1호
• /
• pp.165-170
• /
• 2015

In this paper, The strength and driving characteristics of it were investigated according to developing the traction motor for 8200 electric locomotive series. For this purpose, Flux density strength was analyzed and then structural strength was investigated such as a stator frame, design of the rotor shaft bearing according to the design process. In addition, the traction motor operating point was analyzed according to slip frequency variation at a power source frequency. As the results of analysis on torque-speed characteristic curve, we was confirmed that traction motor was controlled as torque control prior to motor speed 1610[rpm], power control between 1610[rpm] and 2500[rpm] and breakdown torque control more than motor speed 2500[rpm].

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.462-467
• /
• 2010

This paper presents the rotor shape optimization of an interior type permanent magnet (IPM) motor for a reduction of vibration and Electromagnetic Interference (EMI). The vibration and EMI in permanent magnet motors is generated by cogging torque ripple, radial force and commutation torque ripple. Consequently, in order to improve vibration and EMI, the optimal notches are put on the rotor pole with an arc shape proposed. The variation of vibration frequency due to the cogging torque and radial force of each model is computed by the finite element method (FEM). From the analysis result and experiment, we confirmed the proposed model has remarkably improved the vibration and EMI.