• Carbon letters
• /
• 제16권1호
• /
• pp.51-56
• /
• 2015

Carbonate-type organic electrolytes were prepared using propylene carbonate (PC) and dimethyl carbonate (DMC) as a solvent, quaternary ammonium salts, and by adding different contents of 1-ethyl-3-methyl imidazolium tetrafluoroborate ($EMImBF_4$). Cyclic voltammetry and linear sweep voltammetry were performed to analyze conducting behaviors. The surface characterizations were analyzed by scanning electron microscopy method and X-ray photoelectron spectroscopy. From the experimental results, increasing the $EMImBF_4$ content increased the ionic conductivity and reduced bulk resistance and interfacial resistance. In particular, after adding 15 vol% $EMImBF_4$ in 0.2 M $SBPBF_4$ PC/DMC electrolyte, the organic electrolyte showed superior capacitance and interfacial resistance. However, when $EMImBF_4$ content exceeded 15 vol%, the capacitance was saturated and the voltage range decreased.

• Carbon letters
• /
• 제17권1호
• /
• pp.70-73
• /
• 2016

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.331-337
• /
• 2017

Thermal batteries, reserve power source, is activated by melting of molten salt at the temperature range of $350{\sim}550^{\circ}C$. To immobile the molten state electrolyte when the thermal battery is activated, the binder must be added in electrolyte. Usually, molten salts include 30~40 wt% of MgO binder to ensure electrical insulation as well as safety. However, the conventional MgO binder tends to increase ionic conductive resistance and thus the inclusion of the binder increases the total impedance of the battery. This paper mainly focused on the study of yttria stabilized zirconia (YSZ) as an alternative binder for molten salt. The chemical stability between the molten salt and YSZ is measured by XRD and DSC. And the sufficient path for ionic conduction on molten salt could be confirmed by the enhanced wetting behavior and the enlarged pore size of YSZ. The electrochemical properties were analyzed using single cell tests so that it showed the outstanding performance than that using MgO binder.

• 한국세라믹학회지
• /
• 제49권3호
• /
• pp.241-246
• /
• 2012

Physical properties of plasma electrolytic oxidized layers of 8 different kinds of Al alloys, A-1100, A-2024, A-5052, A-6061, A-6063, A-7075, ACD-7B and ACD-12 were investigated. The electrolyte for plasma electrolytic oxidation was mixture of distilled water, $Na_2P_2O_7$, KOH and some metal salts. Growth rate of oxide layer was slower in $Na_2P_2O_7$ electrolyte system than in $Na_2SiO_3$ system, and Ra50 surface roughness of oxidized layer was below $1.2{\mu}m$. Surface hardness in $Na_2P_2O_7$ electrolyte system is higher than in $Na_2SiO_3$ system, and roughness was lower in $Na_2P_2O_7$ electrolyte system than in $Na_2SiO_3$ system.

• 한국재료학회지
• /
• 제25권12호
• /
• pp.694-702
• /
• 2015

Nd-Fe-B permanent magnets have been used in a wide variety of applications because of their high magnetic flux density. So, demand for neodymium has been increasing in worldwide. In this study, an electrowinning process was performed in $LiF-NdF_3-Nd_2O_3$ high temperature molten salts. However, a corrosion resistant material for use in the molten salt must be found for stable operation because of the harsh corrosion environment of the electrowinning process. Therefore, for this paper, boron nitride(BN), aluminum nitride(AlN), and silicon nitride($Si_3N_4$) were selected as protective and structural materials in the high temperature electrolyte. To investigate the characteristics of BN, AlN, and $Si_3N_4$, in molten salts, materials were immersed in the molten salts for 24, 72, 120, and 192 hours. Also, surface condition and stability were investigated by SEM and EDS and corrosion products were calculated by HSC chemistry. As a result, among BN, AlN, and $Si_3N_4$, AlN was found to show the best protective material properties.

• 공업화학
• /
• 제22권3호
• /
• pp.255-260
• /
• 2011

$K^{+}-{\beta}^{{\prime}{\prime}}$-alumina pellet를 이온교환 매체인 ammonium nitrate 수용액과 용융염으로 각각 이온교환하여, 고온형 PEMFC 전해질로 기대되는 무기소재인 $NH_4{^+}-{\beta}^{{\prime}{\prime}}$-alumina를 제조하였다. 고압반응기의 실험조건으로 온도는 130, 150, 170, $200^{\circ}C$ 에서, 시간은 2 h 간격으로 2 h에서 8 h까지 수열반응을 실시하였으며 이 때의 수용액의 농도는 5 M과 10 M을 사용하였다. 또한 $200^{\circ}C$의 가열기 위에서 ammonium nitrate를 완전히 녹여 용융염 상태의 ammonium nitrate를 이용하여 2 h 간격으로 2 h에서 8 h까지 이온교환을 실시하였다. 이온교환반응의 반복횟수에 따른 영향을 알아보기 위하여 재이온교환반응을 3차까지 반복해서 실험하였다. 이후 이온교환 된 $NH_4{^+}-{\beta}^{{\prime}{\prime}}$-alumina 구조체의 상 안정성, 이온교환율을 각각 X선 회절기(Rigaku Rint 2000, Japan)와 ICP-AES (Spectro, Modular EOP)를 사용하여 분석하였다.

• 한국전기전자재료학회논문지
• /
• 제28권7호
• /
• pp.467-472
• /
• 2015

Thermal batteries are primary power sources for military applications requiring high reliability, robustness and long storage life. Conventional electrodes for thermal batteries are prepared by compacting powder mixtures into pellets. Separator is composed of halide mixture, such as LiCl-KCl eutectic salt, blended with MgO to immobilize the molten salt. In order to increase the power density and energy density, the resistance of electrolyte should be reduced because the resistance of electrolyte is predominant in thermal batteries. In this study, wetting behaviors and impregnation weight of molten salts as well as the micro structures of ceramic felt were investigated to be applicable to thin electrolyte. Discharge performances of single cell with the ceramic separator impregnated by molten salt were evaluated also. Zirconia felt with high porosity and large pore outperformed alumina felt in wetting characteristics and molten salt impregnation as well as discharge performances. Based on the results of this study, ceramic felt separator impregnated with molten salt have revealed as an alternative of conventional thick MgO based separator with no conspicuous sign of thermal runaway by short circuit.

• 한국세라믹학회지
• /
• 제42권12호
• /
• pp.827-832
• /
• 2005

In this study, thin electrolyte layer was prepared by 8YSZ ($8mol\%$ Yttria-Stabilized Zirconia) slurry dip and sol coating onto the porous anode support in order to reduce ohmic resistance. 8YSZ polymeric sol was prepared from inorganic salt of nitrate and XRF results of xerogel powder exhibited similar results $(99.2\pm1wt\%)$ compared with standard sample (TZ-8YS, Tosoh Co.). The dense and thin YSZ film with $1{\mu}m$ thickness was synthesized by coating of 0.7M YSZ sol followed by heat-treatment at $600^{\circ}C$ for 1 h. Thin film electrolyte sintered at $1400^{\circ}C$ showed no gas leakage at the differential pressure condition of 3 atm.

• 분석과학
• /
• 제8권4호
• /
• pp.675-682
• /
• 1995

Thin films of buckminsterfullerene($C_{60}$) formed by solution drop casting on Pt foil electrode surfaces were studied by cyclic voltammetry(CV) in acetonitrile(MeCN) containing quaternary ammonium or alkali-metal salts as supporting electrolyte. The electrochemical behaviors of $C_{60}$ films are found to be strongly dependent on the nature of the supporting electrolytes, especially with tetrabutyl ammonium perchlorate (TBAP, $NBu_4ClO_4$), and tetrabutyl ammonium tetrafluoroborate ($TBABF_4$, $NBu_4BF_4$). Reasonably stable films are formed into which electrons can be injected. The interaction of $C_{60}$ film with the quaternary ammonium cation may produce the fulleride salts $(TBA^+)(C{_{60}}^-)$ and $(TBA^+)_2(C{_{60}}^{2-})$. The bulk electroreduction with a controlled potential to generate the soluble $C{_{60}}^{3-}$ anions(dark red-brown color) is followed by electrooxidative deposition to produce a neutral $C_{60}$ film on the surface. The peak currents($I_{pc}$ and $I_{pa}$) of these thin film were dramatically decreased with repetitive potential scanning. These results could be explained by the adsorption-desorption phenomena and ion pairing interaction of reduced species($C{_{60}}^-$, and $C{_{60}}^{2-}$) onto the electrode surface. The peak current changes and peak potential shifts of the thin $C_{60}$ film in cyclic voltammograms formed from solution were observed by varying scan rates.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 1998년도 전지기술 심포지움
• /
• pp.153-166
• /
• 1998

Lithium ion Batteries commercially available since the early nineties in Japan are going to be more and more important for portable electronic devices and even EV applications. Today several companies around the world are working hard to join to market for Lithium secondary batteries. Based on the growing interest for commercial use of batteries also the materials have to be reviewed in order to meet large scale production needs. The requirements especially for electrolytes for lithium batteries are extremely high. The solvents and the lithium salts should be of highest purity. So the supply of these chemicals including packaging, transportation and storage but also the handling in production are critical items in this field. Frolic impurities are very critical for LiPF6 based electrolytes. The influence of water is tremendous. But also the other protic impurities like alcoholes are playing an Important role for the electrolyte quality. The reaction of these species with LiPF6 leads to formation of HF which further reacts with cathode materials (spinel) and anode. To understand the role of the protic impurities more clearly the electrolyte was doped with such compounds and was analyzed for protic impurities and HF. These results which directly show the relation between impurities and quality will be presented and discussed. In addition several investigations on different packaging materials as well as methods to analyze and handle the sensititive material will be addressed. These questions which are only partly discussed in literature so far and never been investigated systematically cover some of the key parameters for understanding of the battery chemicals. This investigation and understanding however is of major importance for scientist and engineers in the field of Lithium ion and Lithium polymer batteries.