• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1245-1251
• /
• 1999

Phase-change optical disk very rapid recording, high densification of data, resulting in high feedback rate and good C/N(carrier to noise) ratio of a feedback signal. However, repetitive thermal energy may cause the deformation of a disk or the lowering of an eliminability and a cyclability of the recording. The lowering of the cyclability can be reduced by insertion of thin layer of ZnS-$SiO_2$ dielectric thin film in appropriate disk structure between the upper and lower part of the recording film. Using the Taguchi method, optimum conditions satisfying both the optimized quality characteristic values and the scattering values for film formation were found to be the target R.F. power of 200W, the substrate R.F. power of 20W, the Ar pressure of 6mTorr, and the electrode distance of 6cm. From the refractive index data, the existence of the strong interaction between the electrode distance and Ar pressure was confirmed, and so was the large effect of the electrode distance on transmittance. According to the analysis of TEM and XRD, the closer the electrode distance was, the finer was the grain size due to the high deposition rate. However, the closer electrode distance brought the negative effect on the morphology of the film and caused the reduction of transmittance. AFM and SEM analyses showed that the closer the electrode distance was, the worse was the morphology due to the high rate of the deposition. Under optimum condition, the deposited thin film showed a good morphology and dense microstructure with less defects.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.314-319
• /
• 2000

Microstructueral development and electrical properties in ZnO-Bi2O3-ZnAl2O4 system were investigated with ZnAl2O4 content(0.1~1.0 mol%). The shrinakge of specimens started around $700^{\circ}C$ and finished at 110$0^{\circ}C$, reaching a maximum shrinkage rate at 80$0^{\circ}C$. The shrinkage rate is strongly related to the fromation of a Bi-rich liquid. The increase of the ZnAl2O4 content inhibited the grain growth of ZnO. Most of ZnAl2O4 particles located at the grain boundaries were about 2~3${\mu}{\textrm}{m}$. ZnO grain size changed little up to 110$0^{\circ}C$, but increased markedly above 115$0^{\circ}C$, especially at lower ZnAl2O4 content. Drastic decreasing in breakdown voltage(Vb) with increasing temperature is expected to be dependent on the ZnO grain size and the distribution of the largest grains between the electrode. The nonlinear I-V characteristic was significantly influenced by the ZnAl2O4 content, which exhibited a maximum value at about 15${\mu}{\textrm}{m}$ of ZnO grain size.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.12
• /
• pp.607-613
• /
• 2001

Molybdenum thin films were deposited on the soda lime glass(SLG) substrates by direct-current planar magnetron sputtering, with a sputtering power density of $4.44W/cm^2$. The working pressure was varied from 0.5 mtorr to 20 mtorr to gain a better understanding of the effect of sputtering pressure on the morphology and microstructure of the Mo film. Thin films of $CU(InGa)Se_2$ (CIGS) were deposited on the Mo-coated glass by three stage co-evaporation process. The highest efficiency device was obtained at the maximum value of the tensive stress. The morphology of Mo-coated films were examined by using scanning electron microscopy The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the residual intrinsic stress were examined by X-ray diffraction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2019

This paper reports the microstructure and electrochemical properties of Si-Al-Fe ternary amorphous alloys prepared by rapid solidification as an anode for lithium secondary batteries. The microstructure was analyzed using XRD and HR-TEM with EDS mapping. In accordance with DSC analysis, annealing was performed to crystallize the active nano-Si in the amorphous alloy. Thus, nano-Si forms (~80 nm) embedded in the matrix alloy, such as $Fe_2Al_3Si_3$, $FeSi_2$, and $Fe_{0.42}Si_{2.67}$, were successfully synthesized. The electrode based on the Si-Al-Fe ternary alloy delivered an initial discharge capacity of approximately $700mAh^{g-1}$, and exhibited a high Coulombic efficiency of 99.0~99.6% from the $2^{nd}$ to $70^{th}$ cycles.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.47-58
• /
• 2024

This study were conduced experimentally to analyze the heat-generating performance, flexural strength, and microstructure of conductive mortar mixed with micro steel fiber and multi-wall carbon nanotube (MWCNT). In the conductive mortar heat-generating performance and flexural strength tests, the mixing concentration of MWCNT was selected as 0.0wt%, 0.5wt%, and 1.0wt% relative to the weight of cement, and micro steel fibers were mixed at 2.0vol% relative to the volume. The performance experiments were conducted with various applied voltages (DC 10V, 30V, 60V) and different electrode spacings (40 mm, 120 mm) as parameters, and the flexural strength was measured at the curing age of 28 days and compared and analyzed with the normal mortar. Furthermore, the surface shape and microstructure of conductive mortar were analyzed using a field emission scanning electron microscope (FE-SEM). The results showed that the heat-generating performance improved as the mixing concentration of MWCNT and the applied voltage increased, and it further improved as the electrode spacing became narrower. However, even if the mixing concentration of MWCNT was added up to 1.0 wt%, the heat-generating performance was not significantly improved. As a result of the flexural strength test, the average flexural strength of all specimens except the PM specimen and the MWCNT mixed specimens was 4.5 MPa or more, showing high flexural strength due to the incorporation of micro steel fibers. Through FE-SEM image analysis, Through FE-SEM image analysis, it was confirmed that a conductive network was formed between micro steel fibers and MWCNT particles in the cement matrix.

• Journal of Hydrogen and New Energy
• /
• v.8 no.1
• /
• pp.11-21
• /
• 1997

$ZrV_{0.7}Mn_{0.5}Ni_{1.2}$ alloy is attractive for anode material in Ni/MH secondary battery because of its large hydrogen storage capacity in gas-solid reaction and long cycling durability in KOH electrolyte. In this work, in order to further improve the discharge performance of this alloy electrode, the alloy was annealed by optimal condition which is for 12 hours at $1000^{\circ}C$. The alloy annealed under optimal condition had higher rate capability and discharge capacity than as-cast one. The microstructure of the as-cast and annealed alloy was investigated by scanning electron microscopy and energy dispersive spectroscopy. Ni content in the matrix was increased, being this homogenized after annealing. Additionally, The measurement of the surface area by B.E.T. analysis showed that there was little difference as-cast and annealed alloy. Therefore, improvement in the rate capability of the annealed alloy is due to increase of Ni content in the matrix.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1100-1101
• /
• 2015

In this work, the effect of addition of acetylacetone on microstructure and quality of nanoporous $TiO_2$ photo-electrodes was studied in dye-sensitized solar cells (DSCs) and structure and electrical properties of fabricated cells were investigated. From the results, the DSCs fabricated with acetyl acetone showed highest photovoltaic performances. This behavior may be attributed to paste agglomeration decrease and interconnection and bonding improvement between $TiO_2$ particles. Furthermore, the most favorable dye absorption time results to be 10h: exceeding this time a decrease in efficiency is observed despite the increasing amount of dye absorption. The $TiO_2$ photo-electrode prepared under the conditions of acetylacetone ratio of 15% and dye absorption time of 10hr showed the better photovoltaic performance ($J_{sc}=12.48mA/cm^2$, $V_{oc}=0.69V$, ff=0.68, ${\eta}=5.86%$).

• Journal of Korean Vacuum Science & Technology
• /
• v.5 no.2
• /
• pp.47-51
• /
• 2001

To obtain high remnant polarization and good crystalinity of ferroelectric thin films in non-volatile memory devices, the high temperature treatment in oxygen ambient is inevitable. Severe problems that occur in this process are oxygen diffusion into substrate, oxidation of electrode and buffer layer, degradation of microstructure and so on. We made ruthenium dioxide thin film by reactive sputtering with oxygen and argon mixture atmosphere. Comparing quantitatively the core-level spectra of Ru and RuO$_2$ obtained by x-ray photoelectron spectroscopy(XPS), we found that chemical state of RuO$_2$ is very stable and of good resistance to oxygen diffusion and oxidation of adjacent layers. It opens the use of RuO$_2$ thin film as a multifunctional layer of good conducting electrode and resistive barrier for the diffusion and the oxidation. We also suggest a correct understanding of Ru 3d core-level spectrum for RuO$_2$ based on the scheme of final state screening and charge transfer satellites.

• Journal of Ceramic Processing Research
• /
• v.18 no.11
• /
• pp.810-814
• /
• 2017

Proton exchange membrane fuel cells (PEMFCs) are some of the most efficient electrochemical energy sources for transportation applications because of their clean, green, and high efficiency characteristics. The optimization of catalyst layer morphology is considered a feasible approach to achieve high performance of PEMFC membrane electrode assembly (MEA). In this work, we studied the effect of the solvent on the catalyst layer of PEMFC MEAs fabricated using the electrostatic spray deposition method. The catalyst ink comprised of Pt/C, a Nafion ionomer, and a solvent. Two types of solvent were used: isopropyl alcohol (IPA) and dimethylformamide (DMF). Compared with the catalyst layer prepared using IPA-based ink, the catalyst layer prepared with DMF-based ink had a dense structure because the DMF dispersed the Pt/C-Nafion agglomerates smaller and more homogeneously. The size distribution of the agglomerates in catalyst ink was confirmed through Dynamic Light Scattering (DLS) and the microstructure of the catalyst layer was compared using field emission scanning electron microscopy (FE-SEM). In addition, the electrochemical investigation was performed to evaluate the solvent effect on the fuel cell performance. The catalyst layer prepared with DMF-based ink significantly enhanced the cell performance (1.2 A cm-2 at 0.5 V) compared with that fabricated using IPA-based ink (0.5 A cm-2 at 0.5 V) due to the better dispersion and uniform agglomeration on the catalyst layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.4
• /
• pp.418-421
• /
• 2023

Multilayer Ceramic Capacitors (MLCCs) are essential passive components in the electronics industry, known for their high capacitance due to the multilayer structure comprising inner electrodes and dielectric layers. Nickel electrodes are commonly used in MLCCs as the inner electrodes, and to prevent oxidation during the co-firing of the dielectric layers with nickel electrodes, reducing atmosphere is required. However, reducing atmosphere sintering can also induce a reduction of the dielectric, necessitating precise control of oxygen partial pressure. To explore the possibility of using oxide electrodes that do not require reducing atmosphere sintering, we analyze the electrical properties of nickel oxide (NiO) as a potential candidate. As a preliminary study on its use as an alternative inner electrode, the correlation between microstructure and electrical properties of bulk NiO under different sintering conditions was investigated to gain insights into the conduction mechanisms of the material.