• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.64-71
• /
• 2015

This paper deals with analysis of armature reaction magnetic field of linear generator with three phases coreless/cored type concentrated winding. On the basis of a magnetic vector potential and Maxwell's equations, governing equations to predict armature reaction field are derived, and current density modeling is also performed analytically by using the Fourier series expansion. The analytical method used in this paper is confirmed by comparing with finite element analysis results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.137-141
• /
• 1996

This paper deals with the prebreakdown phenomena of $SF_{6}$ gap stressed by non-oscillating and oscillating impulse voltages in a strong inhomogeneous field disturbed by a fred needle shaped-protrusion on the earth-side electrode. The breakdown voltage-time characteristics were measured for both positive and negative polarities and over the gas pressure range of 0.1∼0.5 MPa, and the temporal developments of the 77breakdown were observed by a shunt of 50 n. The dependence of the leader stopping time on the gas pressure were obtained. The local field enhancement due to the space charges, which is produced by the streamer corona, has influence with the electrical breakdown of the test gap. The test streamer corona is oxy a necessary condition for the electrical breakdown and the subsequent ionization activities launch the leader at the local field region.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.196-199
• /
• 2009

The practical applications of piezoelectric ceramics are applied not only under low electric field environment. Therefore, an examination for characteristics of PZT ceramics under the high electric field condition can contribute to reducing the susceptibility of multifarious applications and to facilitating production of control circuits. These contributions can lead to the expansion of industrial applications. In this research, we fabricated disk-type PZT ceramic samples using conventional methods, measured the resonance characteristics of these samples under from low to high voltage conditions and calculated the PZT constants.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.3
• /
• pp.1114-1123
• /
• 2017

A linear permanent-magnet vernier (LPMV) motor has magnets and windings in the short mover, which is very suitable for long stroke applications. This paper proposed a new field oriented control with space vector pulse width modulation for the LPMV motor, which considers loss minimization. First, the topology of the LPMV motor is briefly presented. Then, the mathematical model is derived, and the mover field oriented control strategy is proposed. Also, the loss analysis is performed. Finally, the simulated and experimental results are given, verifying the feasibility and effectiveness of the proposed control strategy.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.149-155
• /
• 2002

This paper presents magnetic field analysis technology that uses a vector magnetic characteristic. Recently the magnetic material was found to be measurable using the vector quantity technique. Therefore considering the anisotropy of the magnetic material in the vector field analysis is necessary. The magnetic field analysis method, which is considered the anisotropy by combining the finite element method with the E&$S^2$ (Enokizono, Soda, and Shimoji) modeling, is applied to a permanent magnet motor model.

• Journal of Magnetics
• /
• v.18 no.1
• /
• pp.43-49
• /
• 2013

A pulsed ferrite magnetic field generator (FMFG) was designed for the use in the 1000 m long through-the-earth (TTE) communication system for mining disaster situations. To miniaturize the TTE system, a ferrite core having 10,000 of permeability was used for the FMFG. Attenuation of the magnetic field intensity from the FMFG (200-turn and 0.18 m diameter) was calculated to be 89.95 dB at 1000 m depth soil having 0.1 S/m of conductivity. This attenuation was lower than 151.13 dB attenuation of 1 kHz electromagnetic wave at the same conditions. Therefore, the magnetic-field was found to be desirable as a signal carrier source for TTE communications as compared to the electromagnetic wave. The designed FMFG generates the magnetic field intensity of $1{\times}10^{-10}$ Tesla at 1000 m depth. This magnetic field is detectable by compact magnetic sensors such as flux gate or magnetic tunneling junction sensor. Therefore, the miniature FMFG TTE communication system can replace the conventional electromagnetic wave carrier type TTE system and allow reliable signal transmission between rescuer and trapped miners.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.3
• /
• pp.13-19
• /
• 2020

This study presents the experiment and simulation results on the magnetic field response and electrical stability behaviors of no-insulation (NI) and metal insulation with stainless steel tape (MI-SS) which wound in form of racetrack type coils. First of all, the structural design of the racetrack type bobbin was shown along with its parameters. Then, the current-voltage tests were carried out to measure the critical current of both test coils. Also, the sudden discharging and charging tests were performed in the steady state to estimate the decay field time and magnetic field response, respectively. Finally, the overcurrent tests were conducted in the transient state to investigate the electrical stability of these test coils. Based on the experimental results, the contact surface resistances were calculated and applied to the field coils (FCs) of 10-MW-class second generation high temperature superconducting generator (2G HTSG) used in wind offshore environment. The charging delay time and electrical stability for NI and MI-SS HTS FCs of 10-MW-class 2G HTSG are analyzed by the equivalent circuit model and the key parameters which were obtained from the electromagnetic finite element analysis results.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.300-305
• /
• 2010

This paper presents a two Hall sensor method for rotor angle detection in permanent magnet synchronous motors (PMSM). To minimize the implementation complexity, the system is designed to measure the edge field of permanent magnet pieces. However, there are nonlinearities in the measured values of the edge field. In this work, an angle correction algorithm is proposed, and the improvements in accuracy are verified through experiments. Finally, a field orientation controller is constructed with the proposed angle detection algorithm.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.467-472
• /
• 2020

The superconducting synchronous generator is one of the breakthrough elements for direct-drive wind turbines because it is light and small. Normally the superconducting one has copper armature windings in the stator and superconducting field windings on the rotor. The high resistance of the armature can make large copper losses, comparing with the conventional generators with a gear box. One of the solutions for the large copper losses could be a fully superconducting generator. But the high magnetic fields from the superconducting field windings on the rotor also make high perpendicular magnetic fields on the superconducting tapes in the armature windings. We have proposed a fully superconducting synchronous generator with dual field windings. It could immensely decrease the circumferential component of the magnetic field from the field windings at the armature windings. In this paper, we conceptually designed 3 types of superconducting synchronous generators. The first one is the fully superconducting one with conventional structure, which has superconducting armature windings in the stator and superconducting field windings on the rotor. The second one is the one with dual superconducting field windings and superconducting armature windings between them. The last one is the same as the third one except the structure of the armature. If the concentrated armature windings are superconducting ones with cryostats, then they cannot be installed within the span of 2 poles. So, we adopted 3 phases windings within 4 poles system. It makes more AC losses but can be manufactured really.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.316-323
• /
• 2013

This paper deals with the near-field to far-field calculation for far-field characteristics of antenna and electromagnetic compatibility(EMC) testing. Since the conventional EMC testing process is inefficient such as measurements of the wide band signals and mega structures, Stratton-Chu formula is used to predict the far-field emission by simple and direct process. The usefulness of Stratton-Chu formula is verified by comparing to the analytic solution of the uniform distribution aperture in free-space. In order to inspect the far-fields and to get the near-field values, full-wave simulation solver is utilized. Through the full-wave simulation about the patch antenna, calculated far-field results from Stratton-Chu formula are proven. The predicted magnitudes of the far-field are in error by less than 6 %.