• Journal of Bio-Environment Control
• /
• v.8 no.2
• /
• pp.125-135
• /
• 1999

In this paper, the thermal characteristics in plastic greenhouses with heating systems of electric power, hot air, and non-heating are measured and analyzed by field tests. From these tests, we were able to estimate the heating efficiency and quantitatively evaluate the characteristics of indoor thermal distributions of the particular heating system in greenhouses. The heating system of electric power was ineffective to reduce the difference of thermal distribution in the vertical direction. The hot air heating system also does not properly reduce the serious temperature fluctuation by time. By removing the above problems, these data will be utilized effectively to design better thermal environment in greenhouses.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1050-1060
• /
• 2009

In this paper, a X-Band T/R-module for SAR(Synthetic Aperture Radar) systems based on active phased array antennas is designed and fabricated. The T/R modules have a and width of more than 800 MHz centered at X-Band and support dual, switched polarizations. The output power of the module is 7 watts over a wide bandwidth. The noise figure is as low as 3.9 dB. Phase and amplitude are controlled by a 6-bit phase shifter and a 6-bit digital attenuator, respectively. Further the fabricated T/R module has est and calibration port with directional coupler and power divider. Highly integrated T/R module is achieved by using LTCC(Low Temperature Co-fired Ceramic) multiple layer substrate. RMS gain error is less than 0.8 dB max. in Rx mode, and RMS phase error is less than $4^{\circ}$ max. in Rx/Tx phase under all operating frequency band, or the T/R module meet the required electrical performance m test. This structure an be applied to active phase array SAR Antennas.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.477-483
• /
• 2008

The paper introduces mobile handset multi-band chip antenna to be used on meander line PIFA structure and parasite patch. The proposed antenna uses an FR-4 substrate. The top layer is consist of meander lines PIFA structure to implement GSM900 and is connected with each rad and meander line on the via-hole for maximize space efficiency. The middle layer is designed with the signal line and gap to implement a DCS and PCS bands, the bottom layer which is added to a parasite patch on the ground can be show an adjust of frequency and impedance character by the connection of the radiators of middle layer and coupling. The fabricated antenna with the dimension of $28{\times}6{\times}4\;mm^3$. The ground plane a dimension of $45{\times}90\;mm$, designed by a commercial software CST simulator. The experimental results show that the bandwidth for(VSWR<3) is 90($875{\sim}965$) MHz in GSM900 band operation and 380($1,670{\sim}2,050$) MHz in DCS, PCS band operation. The maximum gains of antenna are 0.25 dBi, 3.65 dBi and 3.3 dBi at resonance frequencies and it has omni-directional pattern practically.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.83-92
• /
• 2005

Fluid conductivity logging has been applied in the boreholes to identify the permeable fi:actures and estimate the origin of saline groundwater in coast area. Fluid replacement technique measures the fluid electrical conductivity with depth at different times in a well after the borehole is first washed out with different water by passing a tube to the borehole bottom. Then formation water flows into the borehole through aquifer such as permeable fractures or porous formation during ambient or pumping condition. Measured conductivity profiles with times therefore indicate the locations of permeable zone or fractures within the open hole or the fully slotted casing hole. As a result of fluid conductivity logging for three boreholes in the study area, it is interpreted that saline groundwater is caused by seawater intrusion through fractured rock, although the effect by land reclamation partially remains. We are planning the quantitative analysis to estimate the hydraulic characteristics using fluid replacement technique, and this approach might be usefully utilized for assessing the characteristics of seawater intrusion, the design of optimal pumping, and estimating the hydraulic properties in coastal aquifer.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.5
• /
• pp.981-986
• /
• 2020

The Internet of Things refers to a space-of-things connection network configured to allow things with built-in sensors and communication functions to interact with people and other things, regardless of the restriction of place or time.IoT is a network developed for the purpose of services for human convenience, but the scope of its use is expanding across industries such as power transmission, energy management, and factory automation. However, the communication protocol of IoT, MQTT, is a lightweight message transmission protocol based on the push technology and has a security vulnerability, and this suggests that there are risks such as personal information infringement or industrial information leakage. To solve this problem, we designed a synchronous MQTT security channel that creates a secure channel by using the characteristic that different chaotic dynamical systems are synchronized with arbitrary values in the lightweight message transmission MQTT protocol. The communication channel we designed is a method of transmitting information to the noise channel by using characteristics such as random number similarity of chaotic signals, sensitivity to initial value, and reproducibility of signals. The encryption method synchronized with the proposed key value is a method optimized for the lightweight message transmission protocol, and if applied to the MQTT of IoT, it is believed to be effective in creating a secure channel.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.1 no.1
• /
• pp.6-25
• /
• 2002

In this paper, we have implemented UPnP Devices which emulate a Control Point, a Light Controller, and a Digital TV. The Control Point has been developed on Linux host system by using C language. The UPnP Devices emulating the Digital TV and Light Controller are running on embedded linux developer board. For the development of UPnP Devices, UPnP SDK API Vl.04 made by Intel Co. Ltd. has been ported on Assabet Linux Reference board to implement the UPnP protocol. After we analyze and design some services of Digital TV device, we have applied UPnP Device program to those devices. UPnP SDK vl .04 consists of APIs which support HTTP, SSDP, SOAP, GENA and XML DOM Level-1 that are cores of UPnP protocol. The C program written for the UPnP Control Point has been compiled and executed on Linux-based PC. The embedded system running on Embedded Linux OS has been connected all together through Ethernet which allows IP-based communications. Under this environment, the UPnP programs are being executed on each device. Control Point, when in operational mode, discovers UPnP Devices on the network and displays the device list on the consol. By selecting one of the functionalities of the device services that are displayed on the Control Point, the controllability has been accomplished. The experiment that we performed in this thesis have revealed that the Control Point and UPnP Devices have supported the protocols including SSDP, SOAP, GENA, and DHCP.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.726-734
• /
• 2015

Relational databases used by structuralizing data are the most widely used in data management at present. However, in relational databases, service becomes slower as the amount of data increases because of constraints in the reading and writing operations to save or query data. Furthermore, when a new task is added, the database grows and, consequently, requires additional infrastructure, such as parallel configuration of hardware, CPU, memory, and network, to support smooth operation. In this paper, in order to improve the web information services that are slowing down due to increase of data in the relational databases, we implemented a model to extract a large amount of data quickly and safely for users by processing Hadoop Distributed File System (HDFS) files after sending data to HDFSs and unifying and reconstructing the data. We implemented our model in a Web-based civil affairs system that stores image files, which is irregular data processing. Our proposed system's data processing was found to be 0.4 sec faster than that of a relational database system. Thus, we found that it is possible to support Web information services with a Hadoop-based big data processing technique in order to process a large amount of data, as in conventional relational databases. Furthermore, since Hadoop is open source, our model has the advantage of reducing software costs. The proposed system is expected to be used as a model for Web services that provide fast information processing for organizations that require efficient processing of big data because of the increase in the size of conventional relational databases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3626-3631
• /
• 2009

This study has provided some of the first experimental results of NMOSFET hot-carrier degradation for the analog circuit application. After hot-carrier stress under the whole range of gate voltage, the degradation of NMOSFET characteristics is measured in saturation region. In addition to interface states, the evidences of hole and electron traps are found near drain depending on the biased gate voltage, which is believed to the cause for the variation of the transconductance($g_m$) and the output conductance($g_{ds}$). And it is found that hole trap is a dominant mechanism of device degradation in a low-gate voltage saturation region, The parameter degradation is sensitive to the channel length of devices. As the channel length is shortened, the influence of hole trap on the channel conductance is increased. Because the magnitude of $g_m$ and $g_{ds}$ are increased or decreased depending on analog operation conditions and analog device structures, careful transistor design including the level of the biased gate voltage and the channel length is therefore required for optimal voltage gain ($A_V=g_m/g_{ds}$) in analog circuit.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.5
• /
• pp.451-457
• /
• 2016

To improve security in the data communication field, many studies on the application of chaotic signals to encryption have been conducted in recent years. In this study, a new security protocol where the initial value sensitivity and noise similarity of chaotic signals have been applied to an RFID communication channel was designed. In the case of chaotic systems, if the initial values become identical, the same signals are generated at the same time after that point even though the two systems have been calculated independently. Therefore, an unpredictable security channel can be produced based on such characteristics. However, a security channel can be produced only when an initial value is shared in advance, and thus there is a potential problem of infringement during the transmission of the initial value. To resolve this problem, a method in which a certain proportion of new chaotic signals are applied to two chaotic systems for communication and are then synchronized after some time was proposed. This new method can conceal the initial value, and thus can resolve the problem of the existing communication method using chaotic signals. The designed method was verified with the encryption and decryption of images. It is expected that a more secure RFID system could be established by applying the communication protocol proposed in this study to insecure RFID communication channels.

• 대한공업교육학회지
• /
• v.38 no.1
• /
• pp.239-258
• /
• 2013

The purpose of this study is to define what circuit repairing ability is and to check improvement in learner's circuit repairing abilities by verifying conformity of learner's achievement of target goals that have been derived from headlight assignment based on circuit repairing ability that has been categorized into six sub-factors, which are preparing ability, attaching/detaching ability, circuit analyzing ability, inspecting and measuring ability, repairing (problem solving) ability and organizing ability. In order to achieve the purpose of study, degree of improvement in circuit repairing ability of learner's group was measured through experiment design and verification by group of experts. SPSS statistics program was used for statistical analysis in which average value for descriptive statistics, Cronbach ${\alpha}$ coefficient and t-test were conducted. Level of significance for t-test was p<.05. The conclusions from conducting this study are as follows. Firstly, the usage of terminology 'circuit repairing ability' pertaining to ability to repair failure of electrical devices in automobiles was confirmed to be appropriate. Secondly, the categorization of circuit repairing ability into sub-factors of preparing ability, attaching/detaching ability, circuit analyzing ability, inspecting and measuring ability, repairing (problem solving) ability and organizing ability was confirmed to be appropriate. Thirdly, field instruction on headlight assignment that has been revised according to achievement of learner's goals was confirmed to be effective in improving learner's circuit repairing abilities compared to regular training. Fourthly, field instruction on headlight assignment that has been revised according to achievement of learner's goals was confirmed to be effective in improving sub-factors of circuit repairing abilities, which are preparing ability, attaching/detaching ability, circuit analyzing ability, inspecting and measuring ability, repairing (problem solving) ability and organizing ability.