• Journal of Korean Society of Transportation
• /
• 제35권3호
• /
• pp.210-219
• /
• 2017

Electric vehicles, which are attracting attention as eco-friendly vehicles, have been increasing in number since 2011 in Korea. The purpose of this study is to analyze the efficient operation of existing charging stations and factors to consider when installing additional charging stations based on the case of Jeju Island where the electric vehicle penetration rate is high and the charging infrastructure is relatively well established. The characteristics of using electric car charging stations by region, type of facility, and time of day are analyzed. As a result of analyzing the frequency of using the charger installed in Jeju Island, the utilization of both the fast charger and the slow charger is found to be concentrated in a specific area. The usage rate of charger installed in a business facility and a public parking lot is high in both fast charger and slow charger. However, according to the usage rate by time of day, the fast charger has a high utilization rate throughout the afternoon, while the use of a slow charger is concentrated in the morning. In order to enable users to utilize the electric vehicle charging station efficiently, it is necessary to provide a publicity guide for the charging station having a low utilization rate, a notice for using the charger, and a notification of completion of charging. Considering the charging demand, the area where the charger is not yet installed should be considered as the area to install the charger, and in addition, the additional installation should be considered in the area and the facility where the amount of charge is large. Service improvement is expected to be possible by utilizing actual electric vehicle charging behavior analysis result.

• The Transactions of the Korean Institute of Power Electronics
• /
• 제20권5호
• /
• pp.479-490
• /
• 2015

The conventional phase-shifted full-bridge (PSFB) converter with an LC filter has been widely used for high-power applications of over 1.0 kW. However, the PSFB converter cannot obtain optimal power conversion efficiency during the battery charging in electric vehicle (EV) on-board battery charger applications because of its unique drawbacks, such as a large circulating current and very high voltage stress in the rectifier diodes. As a result, the converters with a capacitive filter, such as LLC resonant converters, replace the PSFB converter in the EV chargers. This study analyzes the problems of the PSFB converter for EV on-board charger applications in detail. Moreover, the newest converters based on the conventional PSFB converter are reviewed. On the basis of the reviews, new PSFB converter topologies are proposed for EV charger applications. The new topologies are formed by connecting the rectifier stage in the PSFB converter with the output of an LLC resonant converter in series. Many problems of the conventional PSFB converter for EV charger applications can be solved and the performance can be more improved because of this structure; this idea is confirmed by an experiment consisting of prototype battery chargers under the output voltage range of 250-450 Vdc at 3.3 kW.

• The Transactions of the Korean Institute of Power Electronics
• /
• 제18권5호
• /
• pp.443-447
• /
• 2013

This paper deals with LLC resonant converter of on-board charger for electric vehicle charging. Generally, the on-board charger must have a very widely charging voltage, higher efficiency, higher power factor, lower volume and lower weight. For reducing the switching losses, voltage and current stress of the device, the on-board charger is apply the half-bridge LLC resonant converter topology. To have a wide voltage range, it is design the hardware parameters and determine the switching frequency range of the LLC resonant converter. The experimental results show a wide charge voltage.

• Design & Manufacturing
• /
• 제16권2호
• /
• pp.13-19
• /
• 2022

Recently, electric vehicles are gaining popularity among many domestic and foreign users due to their eco-friendly advantages of reducing fine dust and environmental greenhouse gases. As the demand and supply of electric vehicles increase, the demand for electric vehicle charging infrastructure is also growing together. Many users are experiencing inconvenience due to poor charging infrastructure, which makes them hesitant to buy electric vehicles. Research on the user experience of chargers in apartment complexes, a common residential type in Korea, is being conducted somewhat, but research on the design of electric vehicle charging devices in public places is insufficient. The purpose of this research is to identify user requirements and complaints based on the product design of the electric vehicle charger in public places and propose a new electric vehicle product design concept that meets the requirements. The research method understood the charging base and status of electric vehicles in public places through literature research and examined and analyzed the characteristics and problems of product design cases that improved the charging problem of electric vehicles recently released in the market. It is intended to identify and analyze the problems of the charging device product design through user interviews, a qualitative research method, and based on this, it is intended to propose a user-centered product design concept that improves major complaints.

• The Journal of the Korea institute of electronic communication sciences
• /
• 제9권1호
• /
• pp.91-96
• /
• 2014

nowadays, many researches for plug-in hybrid electric vehicles have been actively carried out to improve the gas mileage in comparison with mass-produced hybrid electric vehicles. In this paper, the on-board charger for plug-in hybrid electric vehicles is studied for obtaining the high efficiency. The on-board charger consists of two phase interleaved PFC circuit and LLC resonant converter. The new design procedures of LLC resonant converter are proposed in this paper. These are very simple and powerful method. In order to verify the abovementioned contents, the LLC resonant converter is designed and tested by using PSIM tool.

• The Transactions of the Korean Institute of Power Electronics
• /
• 제27권1호
• /
• pp.74-79
• /
• 2022

This paper proposes a DC-DC converter that satisfies a wide output voltage of 150 V-1000 V for the battery voltage of various electric vehicles and can be controlled in both directions for the demand resource of electric vehicles. The proposed converter is a two-stage structure in which an insulated converter and a non-isolated converter are combined and operates as constant current or constant power depending on the voltage of the connected battery. Experimental results from a 20 kW prototype are provided to validate the proposed charger, and a maximum efficiency of 97% is obtained.

• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1158-1167
• /
• 2015

In this paper, a new hybrid DC-DC converter is proposed for electric vehicle 3.3 kW on-board battery charger applications, which can be modulated in a phase-shift manner under a fixed frequency or frequency variation. By integrating a half-bridge (HB) LLC series resonant converter (SRC) into the conventional phase-shift full-bridge (PSFB) converter with a full-bridge rectifier, the proposed converter has many advantages such as a full soft-switching range without duty-cycle loss, zero-current-switching operation of the rectifier diodes, minimized circulating current, reduced filter inductor size, and better utilization of transformers than other hybrid dc-dc converters. The feasibility of the proposed converter has been verified by experimental results under an output voltage range of 250-420V dc at 3.3 kW.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.268-276
• /
• 2016

A hybrid sinusoidal-pulse current (HSPC) charging method for the Li-ion batteries in electric vehicle applications is proposed in this paper. The HSPC charging method is based on the Li-ion battery ac-impedance spectrum analysis, while taking into account the high power requirement and system integration. The proposed HSPC method overcomes the power limitation in the sinusoidal ripple current (SRC) charging method. The charger shares the power devices in the motor inverter for hardware cost saving. Phase shifting in multiple pulse currents is employed to generate a high frequency multilevel charging current. Simulation and experimental results show that the proposed HSPC method improves the charger efficiency related to the hardware and the battery energy transfer efficiency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제22권4호
• /
• pp.150-159
• /
• 2021

This study aimed to prevent inconvenience to electric vehicle users caused by an interruption of charging by the earth leakage breaker trip that occurs during charging. As a field case study, it was confirmed that during the battery charger failure type, leakage current measurement experiment by vehicle type, and leakage current breaker operation experiment, the internal temperature of the charger rose to more than 60 ℃ in summer, and the earth leakage circuit breaker stopped charging by tripping at 80% of the rated sensitivity current. Through Joule heating modeling, 32A is energized at the reference temperature of 30 ℃ at the initial time t=0 (s). After t=3000 (s), the heat generated around the charging part of the earth leakage breaker increased to 32.4 ℃. The temperature and time factors correlated with the amount of heat generated according to the statistical verification tool with a correlation coefficient of 0.97. Overall, it is possible to prevent the leakage breaker sensitivity current trip due to an increase in temperature inside the charger in summer by performing a Joule heating simulation according to the material of the charging case, the arrangement of the internal wiring, and the dielectric medium when developing the charger device.

• Proceedings of the KIPE Conference
• /
• 전력전자학회 2015년도 추계학술대회 논문집
• /
• pp.25-26
• /
• 2015

Inductive Power Transfer (IPT) method becomes more and more popular for the Electric Vehicle (EV) battery charger due to its convenience and safety in comparison with plugged-in charger. In recent years, Lithium batteries are increasingly used in EVs and Constant Current/Constant Voltage (CC/CV) charge needs to be adopted for the high efficiency charge. However, it is not easy to design the IPT Battery Charger which can charge the battery with CC/CV charge under the wide range of load variation due to the wide range of variation in its operating frequency. This paper propose a new design and control method which makes it possible to implement the CC/CV mode charge with minimum frequency variation (less than 1kHz) during all over the charge process. A 6.6kW prototype charge has been implemented and 96.1% efficiency was achieved with 20cm air gap between the coils.